TRENDnet TL2-E284 Manual de usuario
TL2-E284
1.01
Quick Installation Guide
English 1
1. Before You Start
2. Hardware Installation 2
3. LEDs 3
4. Configure the Switch 5
1
Troubleshooting 9
Table of Contents
Version 11.05.2010
1. Before You Start
Ÿ
ŸA computer with a network adapter properly installed
ŸCAT-5e or CAT-6 Network Cable
ŸThe surface must support at least 2 Kg (4.4 lbs) for the Switch
ŸThe power outlet should be within 1.8 meters (5.9 feet) of the Switch
ŸMake sure that there is proper heat dissipation from and adequate ventilation around the
Switch
ŸDo not place heavy objects on the Switch
Web Browser: Internet Explorer (6.0 or higher)
Ÿ
ŸMini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40, TEG-MGBS80,
TEG-MGBS10D35, TEG-MGBS40D35) for Mini-GBIC slots
EIA standard 19” rack
Package Contents
Ÿ
ŸMulti-Language Quick Installation Guide
ŸCD-ROM (User's Guide)
ŸRS-232 cable (3 m / 9.8 ft.)
ŸPower Cord (1.8 m / 5.9 ft.)
ŸRack Mount Kit
TL2-E284
Installation Requirements
Optional Equipment
1
2
2. Hardware Installation
Note:
Note: The Mini-GBIC slots are shared with port 25 and 26 Gigabit Ethernet ports. When the
Mini-GBIC slots are in use, port 25 and 26 Gigabit Ethernet ports are disabled.
1. Connect the Power Cord to the TL2-E284 and
then to a power outlet.
2. Connect a Cat.5e or Cat.6 RJ-45 network
cable from the computer to an available
Ethernet port on the TL2-E284.
3. Verify that the following panel lights are on:
PWR(Power), SYS(System) and 10M LINK/
ACT, 100M LINK/ACT, 10/100M LINK/ACT or
1000 LINK/ACT.
3
3. LEDs
PWR (Power)
SYS (System)
1000M LINK/ACT
10/100M LINK/ACT
10/100M LINK/ACT
10M LINK/ACT
4
N/A
Green
N/A
Green
Amber
Green
Amber
Ethernet LED (RJ-45)
PWR (Power)
SYS (System)
1000M Link/ACT
100/200Mbps (Half/Full Duplex) Connected (per port)
100/200Mbps (Half/Full Duplex) Data
Transmitting/Receiving (per port)
2000Mbps (Full Duplex) Data Transmitting /
Receiving (per port)
10/20Mbps (Half/Full) or no connection to the port
100/200Mbps (Half/Full), 10/20Mbps (Half/Full),
or no connection to the port
10/20Mbps (Half/Full Duplex) Connected (per port)
10/20Mbps (Half/Full Duplex) or 100/200Mbps
(Half/Full Duplex) Connected (per port)
10/20Mbps (Half/Full Duplex)Data
Transmitting/Receiving (per port)
10/20Mbps (Half/Full Duplex) or 100/200Mbps
(Half/Full Duplex) Data Transmitting/Receiving
(per port)
100/200Mbps (Half/Full), or no connection to the port
2000Mbps (Full), or no connection to the port
Device powered On
Device is ready
Solid
Solid
Solid
Solid
Solid
Off
Solid
Off
Off
Off
Off
Off
Blinking
Blinking
Blinking
Blinking
Green
Device powered Off
Device is not ready
2000Mbps (Full Duplex) Connected (per port)
100M Link/ACT
10M Link/ACT
10/100M Link/ACT
Device Status LED Color
Color
Sequence
Sequence
Definition
Definition
Combo Gigabit Ethernet
(RJ-45) / Mini-GBIC LED Color Sequence Definition
5
4. Configure the Switch
Note:
1. Before the Switch can be configured, a Static IP address must be assigned to your computer's
network adapter in the subnet of 192.168.10.x. Since the Switch's default IP address is
192.168.10.200, make sure no other network devices are assigned an IP address of
192.168.10.200. (Refer to Troubleshooting section on how to configure TCP/IP settings on your
PC.)
2. There are three methods of configuring the TL2-E284: Web Browser, Console Port and Telnet.
1. Using Web Browser
1. Open your web browser, type
http://192.168.10.200 in the Address bar, and
then press Enter.
2. Enter the User name and Password, and then
click Login. By default:
User Name: admin
Password: admin
3. Select the desired options for configuring the
switch.
6
Note:
A terminal program such as HyperTerminal is required to configure the switch via the Console Port.
The instructions shown below demonstrates how to configure the Switch on a Windows PC using
HyperTerminal.
2. Using the Console Port
2. Go to Start Ž Programs Ž Accessories Ž
Communications Ž HyperTerminal
1. Connect the RS-232 cable from a serial port on
your PC to the console port on the switch.
4. Select the correct COM port
(e.g. COM1, COM2) and then click OK.
3. Enter a name, choose an icon and then click
OK.
7
6. Press the Enter Key.
7. Enter the User Name for login. Then press the
Enter. Then Enter the Password and then
press Enter.
By default
login: admin
Password: admin
If you do not see the login prompt, please
power cycle the switch by unplugging the
power cord, wait 15 seconds and then plug it
back in.
5. Enter the following, click Apply and then
click OK.
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
The Telnet function may or may not be included with your computer's operating system. For
instructions on how to enable Telnet in Windows 7/Vista, please refer to the Troubleshooting
section.
3. Using Telnet
1. Click the Windows / Start icon on the bottom
left hand corner and click All Programs.
8
2. Click Accessories and then click Command
Prompt.
3. Type in telnet 192.168.10.200. Then press the
Enter key.
4. Enter the User Name for login. Then press the
Enter. Then Enter the Password and then
press Enter. By default
login : admin
Password: admin
If you do not see the login prompt, please
power cycle the switch by unplugging the
power cord, wait 15 seconds and then plug it
back in.
Configuration is now complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
For detailed information regarding the TL2-E284 configuration and advanced settings, please
refer to User's Guide included on the Utility CD-ROM, or TRENDnet's website at
http://www.trendnet.com.
Otros manuales para TL2-E284
3
Tabla de contenidos
Otros manuales de Cambiar de TRENDnet
TRENDnet
TRENDnet TE-1710 Manual de usuario
TRENDnet
TRENDnet TPE-S88 - Web Smart PoE Switch Manual de usuario
TRENDnet
TRENDnet TE100-SK3 Manual del propietario
TRENDnet
TRENDnet TK-423K - USB/PS/2 KVM Switch Manual de usuario
TRENDnet
TRENDnet TEG-424WS Manual de usuario
TRENDnet
TRENDnet TE100-S24plus Manual de usuario
TRENDnet
TRENDnet TE100-S800i Manual de usuario
TRENDnet
TRENDnet TEG-160WS Manual de usuario
TRENDnet
TRENDnet TU3-H4 Manual de usuario
TRENDnet
TRENDnet TEG-S240TX - DATA SHEETS Manual de usuario
TRENDnet
TRENDnet TK-205K - PS/2 KVM Switch Manual de usuario
TRENDnet
TRENDnet TEG-30284 Manual de usuario
TRENDnet
TRENDnet TE100-S16g Manual de usuario
TRENDnet
TRENDnet TEG-448WS - Switch Manual de usuario
TRENDnet
TRENDnet TE100-SK1plus Manual del propietario
TRENDnet
TRENDnet TI-RP262i Manual de usuario
TRENDnet
TRENDnet TK-208K Manual de usuario
TRENDnet
TRENDnet TEG-240WS Manual de usuario
TRENDnet
TRENDnet TK-401R Manual de usuario
TRENDnet
TRENDnet TE100-S800i Manual de usuario
