TRENDnet TEG-S2620is Manual de usuario

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following

measures:

zReorient or relocate the receiving antenna.

zIncrease the separation between the equipment and receiver.

zConnect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

zConsult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

The availability of some specific channels and/or operational frequency

bands are country dependent and are firmware programmed at the factory

to match the intended destination. The firmware setting is not accessible by

the end user.

European Union Notice:

Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC),

the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by

the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms:

zEN 60950 Product Safety

zEN 300 328 Technical requirement for radio equipment

zEN 301 489-1/-17 General EMC requirements for radio equipment

Trademark recognition

All product names used in this manual are the properties of their respective owners and are

acknowledged.

iii

Contents

1. INTRODUCTION 1

Features................................................................................................................ 2

Package Contents................................................................................................. 2

Ethernet Switching Technology ............................................................................3

2. HARDWARE DESCRIPTION 5

Physical Dimension............................................................................................... 5

Front Panel ........................................................................................................... 5

LED Indicators ...................................................................................................... 6

Rear Panel............................................................................................................7

Desktop Installation............................................................................................... 7

Rack-mounted Installation .................................................................................... 8

3. NETWORK APPLICATION 11

4. CONSOLE MANAGEMENT 14

Main Menu .......................................................................................................... 15

Function Description ........................................................................................... 17

Status and Counters 17

Port Status 17

Port Counters 18

System Information 19

Switch Static Configuration 21

Administration Configuration 21

Port Configuration 25

Trunk Configuration 26

Port Mirroring Configuration 27

VLAN Configuration 29

Priority Configuration 35

MAC Address Configuration 36

Misc Configuration 39

Protocol Related Configuration 42

STP 42

SNMP 45

LACP 50

IGMP/GVRP 54

802.1x Configuration 55

System Reset Configuration 59

Factory Default 59

System Reboot 60

TFTP Configuration 60

X-modem Upgrade 64

5. WEB-BASED MANAGEMENT 66

About Web-based Management ......................................................................... 66

Preparing for Web Management......................................................................... 66

Online Help ......................................................................................................... 67

System Login ...................................................................................................... 67

Port status........................................................................................................... 67

View the Port Information 69

Port Statistics...................................................................................................... 69

Administrator....................................................................................................... 70

IP Address 71

Switch Setting 72

Basic Switch Settings 72

Advanced Setting 73

Misc Config 74

Console Port Information 78

Port Controls 78

Trunking 80

Aggregator setting 80

Aggregator Information 81

State Activity 82

Forwarding and Filtering 84

IGMP Snooping 84

Static MAC Address 85

MAC filtering 86

VLAN configuration 87

Port-based VLAN 88

802.1Q VLAN 90

Spanning Tree 94

System Configuration 95

Per Port Configuration 95

Port Mirroring 96

SNMP Management 97

Security Manager 99

802.1X 100

System Configuration 100

Per port Configuration 101

Misc Configuration 102

TFTP Update Firmware .................................................................................... 102

Configuration Backup........................................................................................ 103

TFTP Restore Configuration 103

TFTP Backup Configuration 104

Factory Default ................................................................................................. 104

System Reboot ................................................................................................. 105

Panel List .......................................................................................................... 105

IP Stacking........................................................................................................ 106

6. TROUBLESHOOTING 109

7. TECHNICAL SPECIFICATION 111

APPENDIX 113

Console Port Pin Assignments ......................................................................... 113

Cables............................................................................................................... 114

100BASE-TX/10BASE-T Pin Assignments ....................................................... 114

LIMITED WARRANTY 116

1. Introduction

Welcome to the World of Network Switching. In the modern business society,

communication and information sharing are fundamental to our life. And computer

networks have proven to be one of the fastest ways of communication.

TEG-S2620is is a multi-port Switch that can be used to build high-performance

switched workgroup networks. This switch is a store-and-forward device that

offers low latency for high-speed networking. The Switch is targeted at workgroup,

department or backbone computing environment.

Figure 1-1. TEG-S2620is

TEG-S2620is features a “store-and-forward “switching scheme. This allows the

switch to auto-learn and store source address in an 8K-entry MAC address table.

MDI (Medium Dependent Interface) Port is also called an "uplink port". The MDI

port does not cross the transmit and receive lines, which is done by the regular

ports (MDI-X ports) that connect to end stations. In general, MDI means

connecting to another Hub or Switch while MDIX means connecting to a

workstation or PC. Therefore, Auto MDI/MDIX means that you can connect to

another Switch or workstation without changing non-crossover or crossover

cabling.

TEG-S2620is has 24 auto-sensing 10/100Base-TX RJ-45 ports and 2 auto detect

Gigabit ports for higher connection speed.

Features

Confirms to IEEE802.3 10BASE-T, 802.3u 100BASE-TX, 802.3ab

1000BASE-T, 802.3z Gigabit fiber

24 10/100 TX plus 2 Gigabit copper/Mini GBIC slot stackable intelligent

switch

High back-plane bandwidth 8.8Gbps

8K-entry MAC address table

Management via single IP address

IGMP support for Multi Media application

Port mirror supported

Support Port bandwidth control

Supports GVRP function

DHCP client supported

Support Port Based VLAN /802 .1Q VLAN

IEEE802.3x Flow control

¾Flow control for full duplex

¾Backpressure for half duplex

Support IEEE802.3ad Port trunk with LACP

Broadcast storm filter supported

Support IEEE 802.1p class of service

Support Port security

IEEE 802.1d Spanning tree protocol supported

Auto detect Gigabit copper and MINI GBIC

Support IEEE 802.1x user authentication

Package Contents

Unpack the contents of the TEG-S2620is and verify them against the

checklist below.

TEG-S2620is

Power Cord

Four Rubber Feet

RS-232 cable

Rack-mounted Kit

User Guide (CD-ROM)

24TX TEG-S2620is Four Rubber Feet RS-232 cable

Rack-mountedKit PowerCord UserGuide(CD-ROM)

Figure 1-2. Package Contents

Compare the contents of your TEG-S2620is package with the standard checklist

above. If any item is missing or damaged, please contact your local dealer for

service.

Ethernet Switching Technology

Ethernet Switching Technology dramatically boosted the total bandwidth of a

network, eliminated congestion problems inherent with CSMA/CD (Carrier Sense

multiple access with Collision Detection) protocol, and greatly reduced

unnecessary transmissions.

This revolutionized networking. First, by allowing two-way, simultaneous

transmissions over the same port (Full-duplex), which essentially doubled the

bandwidth. Second, by reducing the collision domain to a single switch-port,

which eliminated the need for carrier sensing. Third, by using the

store-and-forward technology’s approach of inspecting each packet to intercept

corrupt or redundant data, switching eliminated unnecessary transmission that

slow the network. By employing address learning, which replaced the inefficient

receiving port.

Auto-negotiation regulates the speed and duplex of each port, based on the

capability of both devices. Flow-control allows transmission from a 100Mbps node

to a 10Mbps node without loss of data. Auto-negotiation and flow-control may

require disablement for some networking operations involves legacy equipment.

Disabling the auto-negotiation is accomplished by fixing the speed or duplex of a

port.

Ethernet Switching Technology supplied higher performance at costs lower than

other solutions. Wider bandwidth, no congestion, and the reduction in traffic is

why switching is replacing expensive routers and inefficient hubs as the ultimate

networking solution. Switching brought a whole new way of thinking to networking.

Otros manuales para TEG-S2620is

Tabla de contenidos

Otros manuales de Cambiar de TRENDnet

TRENDnet

TRENDnet TK-205K - PS/2 KVM Switch Manual de usuario

TRENDnet

TRENDnet TE100 S5Pplus Manual de usuario

TRENDnet

TRENDnet TEG-424WS Manual de usuario

TRENDnet

TRENDnet TL2-G244 Manual de usuario

TRENDnet

TRENDnet TL2-G244 Manual de usuario

TRENDnet

TRENDnet TE100-S16g Manual de usuario

TRENDnet

TRENDnet TK-209K Manual de usuario

TRENDnet

TRENDnet TE100-S24plus Manual de usuario

TRENDnet

TRENDnet TPE-T160 Manual de usuario

TRENDnet

TRENDnet TEG-S5g - Gigabit GREENnet Switch Manual de usuario

TRENDnet

TRENDnet TE100-S32plus Manual de usuario

TRENDnet

TRENDnet TEG-240WS Manual de usuario

TRENDnet

TRENDnet TEG-S081FMi Manual de usuario

TRENDnet

TRENDnet TUC-H4E Manual de usuario

TRENDnet

TRENDnet TE100-DX8Eplus Manual de usuario

TRENDnet

TRENDnet TE100-S5 Manual de usuario

TRENDnet

TRENDnet TK-1602R Manual de usuario

TRENDnet

TRENDnet TEG-S224TXA - 26PORT Gigabit Copper Switch 24-10/100... Manual de usuario

TRENDnet

TRENDnet TK-210K Manual de usuario

TRENDnet

TRENDnet TEG-2248WS - Gigabit Web Smart Switch Manual de usuario

TRENDnet

TRENDnet TEG-S80TXE - Copper Gigabit Switch Manual de usuario

TRENDnet

TRENDnet TE100-S24WS Manual de usuario

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch Instrucciones de funcionamiento

TRENDnet

TRENDnet TE100-S800i Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario