Teledyne Lecroy PP006D Manual de usuario

Operator’s Manual

PP006

Passive Probe

700 Chestnut Ridge Road

Chestnut Ridge, NY, 10977-6499

Tel: 845-425-2000, Fax: 845-578-5985

teledynelecroy.com

PP006D Passive Probe Operator’s Manual

Unauthorized duplication of Teledyne LeCroy documentation materials is strictly

prohibited. Customers are permitted to duplicate and distribute Teledyne LeCroy

documentation for internal educational purposes.

Teledyne LeCroy is a trademark of Teledyne LeCroy, Inc. Other product or brand

names are trademarks or requested trademarks of their respective holders.

Information in this publication supersedes all earlier versions. Specifications are

subject to change without notice.

Manufactured under an ISO 9000 Registered Quality Management System.

This electronic product is subject to disposal and recycling regulations

that vary by country and region. Many countries prohibit the disposal of

waste electronic equipment in standard waste receptacles. For more

information about proper disposal and recycling of your Teledyne LeCroy

product, visit teledynelecroy.com/recycle.

929702-00 Rev A

May, 2018

Operator’s Manual

Terms and Symbols

The following symbols appear on the product or in its documentation:

WARNING

High Voltage. Risk of electric shock or burn.

WARNING or

CAUTION

Condition or practice could result in injury or loss

of life, or damage to equipment.

DOUBLE INSULATION

PROTECTIVE (EARTH) TERMINAL

Introduction

The Teledyne LeCroy PP006D is a passive probe with a wide range of

probing accessories. It is designed to give high-impedance probing

capability to a circuit when attached to a Teledyne LeCroy oscilloscope.

To avoid electric shock, keep fingers behind the probe’s finger

guard during use.

The cable has an interior wear indicator that becomes visible when

the wire jacket is excessively worn. If the wear indicator is visible,

do not use the probe.

Rated for indoor use only. Do not operate where conductive

pollutants may be present.

PP006D Passive Probe

Specifications

System

Attenuation

Input

Impedance

B/W

Probe

Length

Compensation

Range

R (MΩ) C (pF) (MHz) (m) (pF)

10x 10 ±2% 12.5 ±10% 500

(-3 dB)

1.514 - 25

Attenuation Ratio ......... 10:1 ± 2% (excepting characteristics of oscilloscope)

Max. Input Voltage....... Circuits not directly connected to Mains: 350 Vrms,

.........................................1400 V transient overvoltage

.........................................Measurement Category II*: 300 Vrms

To reduce risk of fire or electric shock, do not exceed the voltage or

category ratings of the probe. See voltage derating curve on p.4.

Pollution Degree* ......... 2

Operating Altitude ........ Up to 3000 meters (9843 ft)

Max. Operating Temp.. 5 °C to 40 °C (41 °F to 104 °F)

Humidity......................... Up to 80% RH (5 °C to 31 °C)

.........................................Decreasing linearly to 50% RH at 40°C

*As defined in IEC/EN 61010-031. See definitions below.

Definitions:

Measurement Category II (CAT II) refers to measurements performed on circuits directly connected to

utilization points (socket outlets and similar) of the low-voltage mains installation.

Pollution Degree 2 refers to an operating environment where normally only dry, non-conductive

pollution occurs. Temporary conductivity caused by condensation is to be expected.

Operator’s Manual

Input Impedance Profile

PP006D Passive Probe

Voltage vs. Frequency Derating Curve

Not directly connected to Mains

CAT II

General Safety Information

Observe generally accepted safety procedures in addition to those

listed here to avoid personal injury or damage to equipment. The

overall safety of any system incorporating this accessory is the

responsibility of the assembler of the system.

Operator’s Manual

Connect only to grounded instruments. Use only with compatible Teledyne

LeCroy oscilloscopes that have their BNC input connected to an earth

ground. Do not connect the probe reference lead to any point which is at a

potential other than earth ground.

Connect and disconnect properly. Connect probe to the oscilloscope before

connecting it to the test circuit. Disconnect the probe input and reference

lead from the test circuit before disconnecting from the oscilloscope. Do

not connect/disconnect probes that are attached to a live voltage source.

Do not overload. Do not apply any potential to the probe leads that exceeds

the maximum rating of the probe.

Always comply with the Voltage vs. Frequency Derating Curve.

Observe all terminal ratings. Observe all markings on the oscilloscope

before connecting. Consult the oscilloscope product manual for further

ratings information.

Do not remove probe casing.

Do not excessively bend cables.

If the cable wear indicator is visible, do not use the probe.

Use indoors only within operational environment listed. Do not use in wet or

explosive atmospheres. Keep product surfaces clean and dry.

Handle with care. Probe tips are extremely sharp and may puncture skin or

cause other bodily injury if not handled properly.

Keep fingers behind the finger guard of probe body and accessories.

Do not operate with suspected failures. Before each use, inspect the probe

and accessories for damage such as tears or other defects in the probe

body, cable jacket, accessories, etc. If any part is damaged, cease operation

immediately and sequester the probe from inadvertent use.

PP006D Passive Probe

EC Declaration of Conformity

The probe conforms to the applicable European Union

requirements per Low Voltage Directive (LVD) 2014/35/EU.

Compliance was demonstrated to the following specification as listed in

the Official Journal of the European Communities:

IEC/EN 61010-031:2015 Safety requirements for electrical equipment for

measurement, control and laboratory use – Part 031: Safety requirements for

handheld probe assemblies for electrical measurement and test.

EU RoHS Compliance

The probe and accessories conform to the 2011/65/EU RoHS2 Directive.

Disposal

The probe complies with the applicable European Union

requirements to Directives 2012/19/EU and 2013/56/EU on Waste

Electrical and Electronic Equipment (WEEE) and Batteries.

Operator’s Manual

Probe Compensation

Proper compensation of the probe is required to assure amplitude accuracy

of the waveform being measured by matching the probe to the

oscilloscope’s input capacitance. Compensation should be adjusted

whenever the probe is connected to or transferred between oscilloscopes.

1. Connect the sprung hook to the oscilloscope’s CAL OUT terminal and

the ground lead to the GND terminal. Connect the cable to any input

channel.

2. Turn on the input channel and press AUTO SETUP.

3. Adjust the time base and channel Volts/div settings until the signal

contains two cycles as shown below.

4. Use the trimmer tool to adjust the low-frequency trimmer located on

the BNC Compensation Box until you achieve a flat-topped square

wave like the center illustration in the figure below.

CAUTION: Do not apply excessive pressure. The tip of the

trimmer is made of plastic and can break easily.

Over-compensated, correct, and under-compensated waveforms

PP006D Passive Probe

Cleaning

•Clean only the exterior of the probe, cables, and accessories. Use a

soft cotton cloth moistened with a mild detergent and water solution.

Do not allow any portion of the probe to be submerged at any time.

•Dry the probe and accessory thoroughly before attempting to make

any voltage measurement.

•Do not subject the probe to solvents or solvent fumes as these can

cause deterioration of the probe body, cables, and accessories.

Service

Refer all repairs to qualified service personnel. Contact Teledyne LeCroy at

the following address to arrange to return the probe for service:

Teledyne LeCroy, Inc.

700 Chestnut Ridge Road

Chestnut Ridge, NY, 10977-6499

Ph: 800-553-2769 or 845-425-2000

Fax: 845-578-5985

contact.cor[email protected]

For the most complete and up-to-date list of sales and service centers by

country, visit teledynelecroy.com/support/contact.

Otros manuales para PP006D

Tabla de contenidos

Otros manuales de Instrumento de medición de Teledyne Lecroy

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Manual de usuario

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Manual de usuario

Teledyne Lecroy

Teledyne Lecroy USB Advisor T3 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy DL03-ISO Manual de usuario

Teledyne Lecroy

Teledyne Lecroy HVFO108 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy HVFO103 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy PP008 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy HVD3102 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL05-HCM Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Summit T416 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Frontline 802.11 Instrucciones de montaje

Teledyne Lecroy

Teledyne Lecroy PCI Express 2.0 Mid-Bus Probe Guía de configuración

Teledyne Lecroy

Teledyne Lecroy AP015 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Frontline X240 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy CP150 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy ADP300 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy CP030 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Frontline BPA 600 Instrucciones de montaje

Teledyne Lecroy

Teledyne Lecroy PP011-2 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy Frontline BPA 500 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy ZD500 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy AP033 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy RP4030 Manual de usuario

Teledyne Lecroy

Teledyne Lecroy MDA810 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario