Stratasys Objet Series Guía

Caution—

To avoid exposure to skin irritants,

wear protective gloves (provided)

throughout this procedure.

DOC-34032 Rev. A

B. Remove screws B.

C. Loosen screw C.

A. Put on protective gloves. Remove the print block cover.

A. Remove the Support print head card.

B. Loosen the print head thumb screws.

Removing the Support Print Head

Support Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 1

While holding the print head, press down

on the thumb screws and remove it.

DOC-34032 Rev. A

5Make sure you remove the two O-ring

seals along with the print head.

6Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Install the print block cover.

Push on the tab and then pull the jig

downwards to remove it.

DOC-34032 Page 2

Rev. A

Tighten the print head thumb screws.

Press down firmly on the Support print

head card to attach it to the print block.

Installing the Support Print Head

FRONT

PUSH

FIRST

With the print head in the positioning jig,

align it as shown.

Make sure the O-ring seals

are installed on the print head.

FRONT

Remove

Push tab

A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

A. Insert and tighten screws A.

B. Tighten screw B.

Make sure that the Model head is installed as described in Model Print Head Replacement.

Remove the Model print head card.

Removing the Model Print Head

Model Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 3

B. Loosen the print head thumb screws.

DOC-34032 Rev. A

Make sure you remove the two O-ring

seals along with the print head.

2While holding the print head, press down

on the thumb screws and remove it.

To replace the Model print head, you must first remove the Support print head

(see page 1).

Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Installing the Model Print Head

Page 4

DOC-34032 Rev. A

After you replace the Model print-head, re-install the Support head (see page 2).

Push on the tab and then pull the jig

downwards to remove it.

Tighten the print head thumb screws.

Press down firmly on the Model print

head card to attach it to the print block.

FRONT

PUSH

FIRST

Make sure the O-ring seals

are installed on the print head.

FRONT

With the print head in the positioning jig,

align it as shown.

3A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

FRONT

Remove

Push tab

Otros manuales de Impresora 3D de Stratasys

Stratasys

Stratasys Eden350V Manual de usuario

Stratasys

Stratasys F3300 Instrucciones de funcionamiento

Stratasys

Stratasys Objet24 Guía de configuración

Stratasys

Stratasys Objet260 Connex Manual de usuario

Stratasys

Stratasys uPrint Manual de usuario

Stratasys

Stratasys Objet30 Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

Stratasys

Stratasys J750 Manual de usuario

Stratasys

Stratasys Objet260 Connex Manual de usuario

Stratasys

Stratasys Eden260VS Instrucciones de funcionamiento

Stratasys

Stratasys F770 Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

Stratasys

Stratasys Fortus K5 Series Instrucciones de funcionamiento

Stratasys

Stratasys Eden260V Manual de usuario

Stratasys

Stratasys V650 Flex Manual de usuario

Stratasys

Stratasys Eden260V Manual de usuario

Stratasys

Stratasys Objet350 Manual de usuario

Stratasys

Stratasys Fortus 380mc Manual de instrucciones

Stratasys

Stratasys Objet24 Manual de usuario

Stratasys

Stratasys 180-00108 uPrint Manual de usuario

Stratasys

Stratasys F770 Instrucciones de funcionamiento

Stratasys

Stratasys J826 Manual de usuario

Stratasys

Stratasys H350 Manual de usuario

Stratasys

Stratasys uPrint SE Instrucciones de funcionamiento

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

LONGER

LONGER LK4 Pro Manual de usuario

German RepRap

German RepRap X400 Pro V3 Manual de usuario