Stratasys Eden260VS Instrucciones de funcionamiento

DOC-09669 Rev. H

3D Printing System

Site Preparation Guide

Eden260VS

This documentation contains proprietary information of Stratasys Ltd. This information is

supplied solely to assist authorized users of this Stratasys 3D printing system. No part of

this document may be used for other purposes, and it may not be disclosed to other parties.

The specifications on which this document is based are subject to change without notice.

No part of this book may be reproduced in any form or by any means, nor stored in a database

or retrieval system, without prior permission in writing from Stratasys Ltd.

If this document is distributed as a PDF file, you may print it for internal use.

April 2018

DOC-09669 Rev. H

Trademarks

The following are registered trademarks of Stratasys Ltd.: Stratasys®, Objet®, FullCure®.

All names of products and services cited in this book are trademarks or registered

trademarks of their respective companies.

Feedback

If you have any questions or comments about the way information is presented in this

document, or if you have any suggestions for future editions, please send a message to

c-support@stratasys.com.

DOC-09669 Rev. H

Contents

Introduction 5

About this Guide 5

Installation and Training Schedule 5

Physical Description 6

Size and Weight 6

Shipment and Delivery 7

Shipping Information and Customer Responsibility 7

Shipping Pallet 7

Lifting Equipment 7

Unloading 8

Installation Area 9

Floor Plan (Printer Area) 10

Workstation Requirements 11

Electrical Requirements 12

Power 12

Grounding 12

Circuit Breaker 13

Residual Current Device (RCD) 13

Power Connection 13

UPS (Uninterrupted Power Supply) 13

Communication Lines 15

Local Area Network 15

Telephone 15

Environmental Conditions 16

Temperature and Humidity 16

Air Quality 16

Noise Level 16

Accessories and Utilities 17

Start-Up Kit 17

Exhaust Adapter 17

Eyewash Station 17

Compressed Air 18

Fire Safety Equipment 18

DOC-09669 Rev. H 3

Materials Handling and Storage 19

Printing Materials 19

Cleaning Solvent 19

Site Preparation Checklist 20

DOC-09669 Rev. H 4

Introduction

About this Guide

The information and requirements provided in this document ensure proper installation and operation of

the Eden260VS 3D printing system. The customer is responsible for preparing the site as described in

this document, and according to any applicable local regulations.

If you have any questions about the information in this document, contact your Stratasys

representative.

All site requirements must be met before the installation date. The Site Preparation Checklist should

be submitted to your Stratasys representative. Shipping will be arranged after the checklist is received

by Stratasys.

Non-compliance with requirements specified in this document may result in additional installation

charges.

Installation and Training Schedule

• Basic installation and adjustment: 1 work day

• Operator training (operation and maintenance): 1 work day

• Product designer training: ½ work day

• Practice under supervision —1 work day

Eden260VS Introduction

Physical Description

The Eden260VS 3D printing system consists of the following main components:

• printer

• printer computer (built into the printer)

• printer-server workstation (provided by the customer)

Figure 1 Eden260V printers

Size and Weight

Unit W × H × D (cm) W × H × D (inch) Weight (kg/lb)

Eden260V 87 × 120 × 73.5 34.2 × 47.2 × 29 254 kg / 559 lb

Table 1 Size and weight

The following table shows the size and weight information for Eden260V printers.

• W = Width; H = Height; D = Depth

• The depth measurement does not include the fan adapter assembly. If the fan

adapter is ordered, the depth measurement increases to 80 cm/31.5 inches (see

"Exhaust Adapter" on page 17).

Eden260VS Physical Description

Shipment and Delivery

Shipping Information and Customer Responsibility

Shipment to the customer will be arranged by a Stratasys distributor as indicated in the “ship to” part of

the invoice.The customer is responsible for providing detailed delivery information, including, whether

or not there is loading dock at the delivery site.

The customer is responsible for transporting the printer to a suitable installation site. Upon request,

your Stratasys service provider will advise regarding these matters.

Note:

Only Stratasys-certified Customer Support Engineers are authorized to unpack and

install equipment supplied.

Shipping Pallet

The following table shows the approximate size and weight of the printing system mounted on a pallet.

Unit W × H × D (cm) W × H × D (inch) Weight (kg/lb)

Eden260V 112 × 143 × 89 44.1 × 56.3 × 35 300 kg / 660 lb

Table 2 Size and weight of printer on shipping pallet

W = Width; H = Height; D = Depth

Lifting Equipment

A forklift or hand-operated pallet truck with the following specifications is required:

• lifting capacity: 500 kg (1100 lb)

• extension: 150 cm (60 in.)

Eden260VS Shipment and Delivery

Unloading

The unloading area should be a level surface.

An area of 10 m2 (108 sq ft) is required for the forklift to remove the printer from the delivery truck.

A clearance of 120 cm (4 ft) around the back and sides of the packaging is required for unpacking the

printer.

A clearance of 180 cm (6 ft) from the front is required for unloading the printer from the pallet.

The installation location must be accessible from the unloading area. The customer is responsible for

unloading the printer from the truck and transferring it to the installation location.

Eden260VS Shipment and Delivery

Installation Area

The installation area should be free of sources of vibration and electromagnetic interference that could

affect the proper functioning of the printer.

The floor gradient should be less than 0.5% (5 mm per meter).

The floor should be stable and able to bear the load of the printer. The minimum floor load is 560 kg/m2

(115 lb/ft2).

The server workstation and the printer should be located in the same room.

The cable between the server workstation and the printer should not exceed 5 meters (16 feet). The

communication cable provided should not be extended or replaced with a longer cable.

Clearance around and above the printer should ensure convenient access and servicing.

The area around the printer should remain dry at all times. Do not place the cleaning station within

5 meters (16 feet) of the printer.

Shelves and cabinets are recommended near the printer for convenient storage of tools, parts,

accessories, manuals, and materials.

Eden260VS Installation Area

Floor Plan (Printer Area)

The following is a sample floor plan, showing the 3D printing system—the printer and the workstation.

The dimensions shown in the figure are the minimum clearance requirements.

Figure 2 Printer floor plan (sample, not to scale)

Eden260VS Installation Area

Tabla de contenidos

Otros manuales de Impresora 3D de Stratasys

Stratasys

Stratasys Fortus 360mc Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

Stratasys

Stratasys Objet24 Guía de configuración

Stratasys

Stratasys 180-00108 uPrint Manual de usuario

Stratasys

Stratasys Dimension BST 1200 Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

Stratasys

Stratasys J750 Manual de usuario

Stratasys

Stratasys Fortus 360mc Guía de referencia

Stratasys

Stratasys V650 Flex Manual de usuario

Stratasys

Stratasys K6 Series Manual de usuario

Stratasys

Stratasys F170 Manual de instrucciones

Stratasys

Stratasys Fortus 900mc Manual de instrucciones

Stratasys

Stratasys F123 Series Manual de usuario

Stratasys

Stratasys Fortus 900mc Instrucciones de funcionamiento

Stratasys

Stratasys J4100 Manual de usuario

Stratasys

Stratasys Objet350 Manual de usuario

Stratasys

Stratasys Objet500 Manual de usuario

Stratasys

Stratasys Connex500/350 Manual de usuario

Stratasys

Stratasys Fortus 360mc Instrucciones de funcionamiento

Stratasys

Stratasys F120 Instrucciones de funcionamiento

Stratasys

Stratasys Connex500 Manual de usuario

Stratasys

Stratasys Objet24 Manual de usuario

Stratasys

Stratasys V650 Flex Instrucciones de funcionamiento

Stratasys

Stratasys P750K Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

LONGER

LONGER LK4 Pro Manual de usuario

German RepRap

German RepRap X400 Pro V3 Manual de usuario