Stratasys J826 Instrucciones de funcionamiento

DOC-18005 Rev. E

3D Printing System

Site Preparation Guide

Stratasys J826

No part of this document may be photocopied, reproduced, or translated into any human or computer language in any

form, nor stored in a database or retrieval system, without prior permission in writing from Stratasys. This document may

be printed for internal use only. All copies, shall contain a full copy of this copyright notice.

www.stratasys.com

Trademarks

Stratasys,and Stratasys J826 are trademarks of Stratasys and/or subsidiaries or affiliates and may be registered in

certain jurisdictions. All other product names and trademarks are the property of their respective owners.

Liability

Stratasys shall not be liable for errors contained herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material. Stratasys makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. It is the

responsibility of the system owner/material buyer to determine that Stratasys material is safe, lawful, and technically

suitable for the intended application as well as identify the proper disposal (or recycling) method consistent with local

environmental regulations. Except as provided in Stratasys' standard conditions of sale, Stratasys shall not be

responsible for any loss resulting from any use of its products described herein.

Disclaimers

Customer acknowledges the contents of this document and that Stratasys parts, materials, and supplier are subject to its

standard terms and conditions, available on http://www.stratasys.com/legal/terms-and-conditions-of-sale, which are

incorporated herein by reference.

The specifications and/or information on which this document is based are subject to change without notice.

Feedback

If you have any questions or comments about the way information is presented in this document, or if you have any

suggestions for future editions, please send a message to

c-support@stratasys.com.

DOC-18005 Rev. E

Contents

Introduction 5

About this Guide 5

Installation and Training Schedule 5

Physical Description 6

Size and Weight 6

Shipment and Delivery 7

Shipping Information and Customer Responsibility 7

Shipping Pallet 7

Lifting Equipment 7

Unloading 8

Installation Area 10

Floor Plan (Printer Area) 10

Workstation Requirements 11

Electrical Requirements 12

Power 12

Grounding 12

Circuit Breaker 13

Residual Current Device (RCD) 13

Power Connection 13

UPS (Uninterrupted Power Supply) 13

Communication Lines 15

Local Area Network 15

Telephone 15

Environmental Conditions 16

Temperature and Humidity 16

Air Quality 16

Noise Level 16

Accessories and Utilities 17

Start-Up Kit 17

Exhaust Adapter 17

Compressed Air 18

Fire Safety Equipment 18

Materials Handling and Storage 19

Printing Materials 19

Cleaning Solvent 19

Site Preparation Checklist 20

Introduction

About this Guide

The information and requirements provided in this document ensure proper installation and operation of

the Stratasys J826 printing system. The customer is responsible for preparing the site as described in this

document, and according to any applicable local regulations.

If you have any questions about the information in this document, contact your Stratasys representative.

All site requirements must be met before the installation date. The Site Preparation Checklist should be

submitted to your Stratasys representative. Shipping will be arranged after the checklist is received by

Stratasys.

Non-compliance with requirements specified in this document may result in additional installation

charges.

Installation and Training Schedule

• Basic installation and adjustment: 1 work day

• Operator training (operation and maintenance): 1 work day

• Product designer training (advanced features and work flow): ½ work day

• Practice under supervision: 1½ work days

Stratasys J826 Introduction

Physical Description

The Stratasys J826 printing systems consist of the following main components:

• printer

• material cabinet

• printer computer (built into the printer)

• client workstation provided by the customer

Figure 1 Stratasys J826 printer

Size and Weight

Unit W × H × D

(cm)

W × H × D (inch) Weight (kg/lb)

Printer 87 × 120 × 73.5 34.2 × 47.2 × 29 234 kg / 516 lbs

Materials cabinet 67 x 110 x 64 26.4 x 43.3 x 25.2 152 kg / 335 lbs

Table 1 Size and weight

• W = Width; H = Height; D = Depth

• The depth measurement does not include the fan adapter assembly. If the fan

adapter is ordered, the depth measurement increases to 80 cm/31.5 inches (see

"Exhaust Adapter" on page 17).

Stratasys J826 Physical Description

Shipment and Delivery

Shipping Information and Customer Responsibility

Shipment to the customer will be arranged by a Stratasys distributor as indicated in the “ship to” part of the

invoice.The customer is responsible for providing detailed delivery information, including, whether or not

there is loading dock at the delivery site.

The customer is responsible for transporting the printer to a suitable installation site. Upon request, your

Stratasys service provider will advise regarding these matters.

Note:

Only Stratasys-certified Customer Support Engineers are authorized to unpack and

install equipment supplied.

Shipping Pallet

The following table shows the approximate size and weight of the printing system mounted on a pallet.

Unit W × H × D (cm) W × H × D (inch) Weight (kg/lb)

Stratasys J826 149 × 159 × 138 58.7 × 62.6 × 54.3 425 kg / 936 lb

Materials cabinet 109 × 139 × 94 42.7 × 54.7 × 37 240 kg / 529 lbs

Table 2 Size and weight of printer on shipping pallet

W = Width; H = Height; D = Depth

Lifting Equipment

• lifting capacity: 500 kg (1100 lb)

• extension: 150 cm (60 in.)

Stratasys J826 Shipment and Delivery

Unloading

The unloading area should be a level surface.

An area of 10 m2 (108 sq ft) is required for the forklift to remove the printer from the delivery truck.

A clearance of 120 cm (4 ft) around the back and sides of the packaging is required for unpacking the

printer.

The installation location must be accessible from the unloading area. The customer is responsible for

unloading the printer from the truck and transferring it to the installation location. Minimum space

requirements for unloading the printer are shown in the figure below.

Figure 2 Unloading dimensions—top view

Note:

Dimensions are shown in centimeters.

Stratasys J826 Shipment and Delivery

Figure 3 Printer center of gravity

Stratasys J826 Shipment and Delivery

Installation Area

The installation area should be free of sources of vibration and electromagnetic interference that could

affect the proper functioning of the printer.

The floor gradient should be less than 0.5% (5 mm per meter).

The floor should be stable and able to bear the load of the printer. The minimum floor load is 630 kg/m2

(129 lb/ft2).

The server workstation and the printer should be located in the same room.

The cable between the server workstation and the printer should not exceed 5 meters (16 feet). The

communication cable provided should not be extended or replaced with a longer cable.

Clearance around and above the printer should ensure convenient access and servicing.

The area around the printer should remain dry at all times. Do not place the cleaning station within

5 meters (16 feet) of the printer.

Shelves and cabinets are recommended near the printer for convenient storage of tools, parts,

accessories, manuals, and materials.

Floor Plan (Printer Area)

The following is a sample floor plan, showing the 3D printing system—the printer, the materials cabinet,

and the workstation. The dimensions shown in the figure are the minimum clearance requirements.

Figure 4 Printer floor plan (sample, not to scale)

Stratasys J826 Installation Area

Otros manuales para J826

Tabla de contenidos

Otros manuales de Impresora 3D de Stratasys

Stratasys

Stratasys Fortus 900mc Instrucciones de funcionamiento

Stratasys

Stratasys F770 Instrucciones de funcionamiento

Stratasys

Stratasys Objet24 Guía de configuración

Stratasys

Stratasys F3300 Instrucciones de funcionamiento

Stratasys

Stratasys Fortus 360mc Manual de usuario

Stratasys

Stratasys J750 Manual de usuario

Stratasys

Stratasys Fortus 900mc Guía de referencia

Stratasys

Stratasys Fortus 900mc Manual de instrucciones

Stratasys

Stratasys J850 Manual de usuario

Stratasys

Stratasys UV800 Manual de usuario

Stratasys

Stratasys uPrint Manual de usuario

Stratasys

Stratasys F170 Manual de usuario

Stratasys

Stratasys P750K Manual de usuario

Stratasys

Stratasys F123 Series Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

Stratasys

Stratasys Connex500 Manual de usuario

Stratasys

Stratasys 180-00108 uPrint Manual de usuario

Stratasys

Stratasys Eden250 Manual de usuario

Stratasys

Stratasys Objet30 Manual de usuario

Stratasys

Stratasys J826 Manual de usuario

Stratasys

Stratasys Objet24 Manual de usuario

Stratasys

Stratasys Eden260VS Instrucciones de funcionamiento

Stratasys

Stratasys Eden260V Manual de usuario

Stratasys

Stratasys Fortus 250mc Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

LONGER

LONGER LK4 Pro Manual de usuario

German RepRap

German RepRap X400 Pro V3 Manual de usuario