StarTech.com IDECASE525U2 Manual de usuario
Drive Case
IDECASE525U2 Instruction Manual
Actual product may vary from photo
External USB 2.0 Drive Enclosure for 5.25” IDE Drives
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this
document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing a 5.25” Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing a 3.5” Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Locking and Unlocking Your Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Windows 2000/XP/2003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Windows 98SE/ME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Connecting Your External Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Using Your External Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Related Products from StarTech.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Instruction Manual
i
Introduction
Thank you for purchasing a StarTech.com 5.25” external storage device. Designed for
CD-ROM, CD-RW, DVD, or any other 5.25” IDE drive, this device makes data
transportation, backup, and sharing easier than ever before. The IDECASE525U2
features USB V2.0 capabilities, meaning you’ll experience super-fast data transfer
speeds of up to 480 Mbps. With full Plug and Play capabilities, the device is a snap to
install and use.
Features
•Transfers data at speeds up to 480 MBits/sec.
•Cooling side fan keeps drive running at optimal temperatures
•Also supports 3.5” hard drives when used with drive adapter bracket (StarTech.com
part number BRACKET, not included)
•Compatible with USB 2.0-enabled IBM compatible computers
•Complies with Plug and Play specifications
•Backed by StarTech.com’s one-year warranty
Before You Begin
System Requirements
•Any IBM compatible computer with an available USB 2.0 port and running Windows
98SE/ME/2000/XP/2003
Contents
This package should contain:
•1x IDECASE525U2 external storage case
•1x USB 2.0 cable
•1x power cord
•1x assorted screws
•1x plastic front bezel panel (for hard drives)
•1x driver CD
Instruction Manual
1
Installation
This section will guide you through the installation of your IDECASE525U2. Please read
through the instructions carefully and complete each step in the order listed.
In order to open your case, you may need to unlock it. Please see Locking and
Unlocking Your Case on page 3.
Installing a 5.25” Drive
NOTE: Before installing a drive in the case, consult your drive manufacturer’s installation
instructions for specific details or procedures for installing the drive.
1. Make sure that the external case is not plugged in and that you are grounded.
2. Simultaneously press the arrow buttons on either side of the case and lift the cover.
3. Gently slide your 5.25” disk into the case through the hole in the front panel after
removing the front bezel panel from the front of the drive case.
4. Connect the beige-gray IDE ribbon to your drive’s IDE port, making sure the red
stripe is on pin 1. If you are unsure of the location of pin 1, consult your drive
manufacturer.
5. Connect the power connector (red, black, and yellow wires) to your drive’s power
port. The connectors are formed so that it is difficult to connect them incorrectly.
6. Connect the sound wires (white, black, red) to the sound connectors on your drive,
if applicable.
7. Gently position your drive so that it is flush with the front of the case and the
screwholes on the drive line up with the screwholes in the case. Secure the drive in
place using the provided screws.
Installing a 3.5” Hard Drive
Consult your hard drive manufacturer for any specific instructions prior to installing the
hard drive. Make sure that you have properly configured your hard disk according to your
hard disk manufacturer’s specifications. In general, however, this device works best in
Master mode.
NOTE: In order to use a 3.5” hard drive in this device, you will need a 3.5” to 5.25”
adapter, like the StarTech.com BRACKET (not included).
1. Make sure that the external case is not plugged in and that you are grounded.
2. Secure your 3.5” hard drive to the bracket as outlined by the bracket manufacturer.
3. Simultaneously press the arrow buttons on either side of the case and lift the cover.
4. Connect the beige-gray IDE ribbon to your drive’s IDE port, making sure the red
stripe is on pin 1. If you are unsure of the location of pin 1, consult your drive
manufacturer.
5. Connect the power connector (red, black, and yellow wires) to your drive’s power
Instruction Manual
2
port. The connectors are formed so that it is difficult to connect them incorrectly.
6. Gently position your drive so that the screwholes on the bracket line up with the
screwholes in the case. Secure the drive in place using the provided screws and
attach the plastic front panel to the front of the case.
Locking and Unlocking Your Case
You can prevent the case from being unintentionally opened by moving the switch
underneath the arrow buttons at the front sides of the case to the LOCK position.
Driver Installation
The most up-to-date drivers for this device are available as a free download on our Web
site. Go to www.startech.com/support for more details.
Windows 2000/XP/2003
Windows 2000/XP/2003 includes native support for USB 2.0 and will install the drivers
automatically. Ensure you have the current Microsoft Service Pack installed.
Windows 98SE/ME
Follow this procedure before attempting to connect the drive case to your computer:
1. Insert the driver CD into your computer’s CD-ROM or other optical drive.
2. Double-click My Computer. Double-click the icon that represents your CD-ROM
drive.
3. Double click the folders in the following order: PC WINDOWS >CY-WIN-5.04.
4. Double-click the TPPINST_5_04.EXE file and follow the on-screen instructions.
Choose a Complete installation when prompted.
5. Restart the computer when prompted.
Connecting Your External Case
1. Make sure that your system is turned off.
2. Plug one end of the USB 2.0 cable into an open USB 2.0 port on your computer.
Plug the other end into an open USB 2.0 port on the case.
3. Plug the power cable into the power port on the back of the case and plug the other
end into an available power source.
4. When applicable, connect your speakers into the sound ports on the back of the
enclosure. Connect your left speaker to the white port and your right speaker to the
red port.
5. Power the device by switching the small button on the back to the ON (I) position.
Instruction Manual
3
The green power LED on the front of the case should now be lit.
6. Turn your computer on.
NOTE: For information on the partitioning and formatting of new hard disks, consult the
instruction manual that accompanies your operating system or consult your computer
manufacturer for the proper procedures.
Using Your External Case
When the new drive is connected, it will appear as an icon on the bottom right of your
screen. You can double-click the icon for information on the drive. The device will also
appear under your My Computer window. You can now use the drive as you would any
other drive on your system.
When you want to remove your external case, first make sure that there is no activity on
the hard drive contained in the case. Do not remove or shut down the case if the yellow
activity LED is on. When you are certain the hard drive has “spun down,” right-click the
drive icon and click on Safely remove device. When the icon is removed from your
screen, turn off the power to the external drive by turning the power button on the back
to the OFF (O) position and disconnect the USB 2.0 cable.
Instruction Manual
4
Related Products from StarTech.com
Contact your local StarTech.com dealer or visit www.startech.com for cables or other
accessories that will help you get the best performance out of your new product.
5.25 Inch External IEEE-1394 FireWire IDE Drive Case Enclosure
IDECASE525F
2 Port USB 2.0 PCI Card
PCI220USB
5 Port USB 2.0 PCI Card
PCI4USBV2
15 ft High Speed USB 2.0 Cable
USB2HAB15
10 ft High Speed Certified USB 2.0 Cable
USB2HAB10
6 ft High Speed Certified USB 2.0 Cable
USB2HAB6
3 Port USB 2.0 CardBus Laptop Adapter
CBUSB2
2 Port USB 2.0 CardBus Laptop Adapter
CBUSB220
Value 2 Port USB 2.0 PCI Card
PCI225USB
Value 4 Port USB 2.0 PCI Card
PCI425USB
Value 6 Port USB 2.0 PCI Card
PCI625USB2I
Instruction Manual
5
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit our Web site to
access our comprehensive selection of online tools, documentation, and downloads.
USA/Canada: www.startech.com/support
UK/Ireland/Europe: uk.startech.com/tech_support
Warranty Information
This product is backed by a one-year warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted, following
the initial date of purchase. During this period, the products may be returned for repair, or
replacement with equivalent products at our discretion. The warranty covers parts and
labor costs only. StarTech.com does not warrant its products from defects or damages
arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement
may not apply to you.
Instruction Manual
6
Revised: 19 November 2004 (Rev. C)
Tabla de contenidos
Otros manuales de Recinto de StarTech.com
StarTech.com
StarTech.com InfoSafe SAT3510U2B Manual de usuario
StarTech.com
StarTech.com 8STS25SLOTR Manual de usuario
StarTech.com
StarTech.com INFOSAFE SAT2510BU2 Manual de usuario
StarTech.com
StarTech.com SATSASBAY425 Manual de usuario
StarTech.com
StarTech.com S2510BU3PW Manual de usuario
StarTech.com
StarTech.com S2510BMU33CB Manual del sistema
StarTech.com
StarTech.com S3510BMU33B Manual de usuario
StarTech.com
StarTech.com S3510BMU33T Manual del sistema
StarTech.com
StarTech.com DRW110SAT Manual de usuario
StarTech.com
StarTech.com HSB320SATBK Manual de usuario
StarTech.com
StarTech.com S2510PESAT Manual de usuario
StarTech.com
StarTech.com S2510BPU337 Manual de usuario
StarTech.com
StarTech.com UNI2510U2V Manual de usuario
StarTech.com
StarTech.com SAT2510U2F Manual de usuario
StarTech.com
StarTech.com SAT3510U2REM Manual de usuario
StarTech.com
StarTech.com 2636CABINET Manual de usuario
StarTech.com
StarTech.com SAT3540ER2 Manual de usuario
StarTech.com
StarTech.com RK1219WALHM Manual de usuario
StarTech.com
StarTech.com RK1232WALHM Manual de usuario
StarTech.com
StarTech.com S351BMU33ETG Manual de usuario
