StarTech.com S2510BPU33 Manual de usuario
Manual Revision: 05/28/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
S2510BPU33
2.5” Tool-less USB 3.0 to SATA III HDD
Enclosure with UASP Support
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Top View ....................................................................................................................................................... 1
Front View .................................................................................................................................................... 1
Introduction ............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements .............................................................................................................................. 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
How to Use ..............................................................................................5
Specications ..........................................................................................8
Technical Support ..................................................................................9
Warranty Information ............................................................................9
Instruction Manual
1
Product Diagram
Top View
Front View
USB 3.0 Micro-B
(10 pin; SuperSpeed)
Instruction Manual
2
Introduction
Packaging Contents
• 1x 2.5” USB 3.0 to SATA III HDD Enclosure
• 1x HDD Pad
• 1x USB 3.0 Cable
• 1x Product Manual
System Requirements
• Computer system with available USB 3.0 (5 Gbit/s) port or USB 2.0 port (480Mbps)
• 2.5” SATA hard drive or solid state drive (9.5mm height)
• Microsoft® Windows® 2000/XP/Server 2003/Vista/Server 2008 R2/7/8 (32/64-bit), or
Apple® Mac® OS 9.x/10, or Linux®
Instruction Manual
3
Installation
Hardware Installation
WARNING! Hard drives and storage enclosures require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
1. Open the enclosure by sliding the top panel away from the USB port, and lifting
from the enclosure base.
2. Attach the included “HDD Pad” to the back side of the 2.5” Hard Drive, oposite the
SATA connector.
Instruction Manual
4
3. Connect the the 2.5” SATA Hard Drive
4. Align the hooks on the top panel with the groves on the Base of the enclosure and
slide the top panel back into place.
Instruction Manual
5
5. With the enclosure fully assembled, connect the USB 3.0 cable from the enclosure to
a USB port on the host computer system using the included cable.
How to Use
Connecting the Hard Drive
Once the enclosure has been attached to a computer, and the necessary software has
been installed, the drive will be accessible as though it were installed within
the system.
Prior to using the drive, it will need to be formatted according to your operating
system requirements. To format your newly attached hard drive, or create partitions,
please consult the documentation that accompanied your operating system at the
time of purchase.
Powering the Drive Enclosure
The hard drive enclosure requires no external power supply, as it is capable of receiving
enough power from the USB Bus to which it is connected.
LED Indicator
The hard drive enclosure oers an LED indicator, to enable you to monitor drive
activity. When the enclosure is powered, the LED will illuminate. While the hard drive
is being accessed, the LED will blink. Do not remove the enclosure from the host
computer while the LED is ashing, as it could damage the drive or the enclosure,
resulting in data loss.
Instruction Manual
6
Disconnecting the Hard Drive
Windows
1. Select the “Safely remove Hardware and Eject Media” icon, located in the task bar.
2. Select “Eject USB Device” from the list that appears.
3. Wait for the message indicating that it is now safe to remove the device.
NOTE: Removing the connected drive prior to receiving notication that it is safe
to do so, could result in losing or corrupting data stored on the drive. Once the Safe
to Remove Hardware message appears, please disconnect the enclosure from the
computer by removing the USB connection.
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows
listing the contents of the removable drive. Once all windows are closed, click on the
USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop.
Allow 5 seconds before physically removing the enclosure/drive from the computer.
Initializing the Hard Drive
1. If the SATA Hard Drive is blank it may need to be initialized and formatted before
use. From the main Windows desktop, right-click on “My Computer” (“Computer” in
Vista/ 7 / 8), then select Manage. In the new Computer Management window, select
Disk Management from the left window panel.
Instruction Manual
7
2. A dialog window should automatically appear, asking you to initialize the drive.
Depending on the version of Windows, it will give you the option of either creating
an “MBR” or “GPT” disk. GPT (GUID partition) is not compatible with some older
operating systems, while MBR is supported by newer and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard
drive capacity to conrm it’s the correct hard drive) and then right-click in the
section that says “Unallocated” and select “New Partition”.
Tabla de contenidos
Otros manuales de Recinto de StarTech.com
StarTech.com
StarTech.com IDECASE35U2B Manual de usuario
StarTech.com
StarTech.com SAT3520UERGB Manual de usuario
StarTech.com
StarTech.com IEEE-1394b Manual
StarTech.com
StarTech.com S2510BMU33 Manual del sistema
StarTech.com
StarTech.com ESATCASE2 Manual de usuario
StarTech.com
StarTech.com 8STUNI251BMU33 Manual de usuario
StarTech.com
StarTech.com SAT3510U2F Manual de usuario
StarTech.com
StarTech.com ATXFULL635V Manual
StarTech.com
StarTech.com MADE EASY HSB110SATBK Manual de usuario
StarTech.com
StarTech.com SAT2MSAT25 Manual de usuario
StarTech.com
StarTech.com S354UFER Manual de usuario
StarTech.com
StarTech.com INFOSAFE IDE2510U2 Manual de usuario
StarTech.com
StarTech.com IDE3510U2GB Manual de usuario
StarTech.com
StarTech.com SAT2510BU3 Manual de usuario
StarTech.com
StarTech.com SW-3023 Manual de usuario
StarTech.com
StarTech.com SAT3520U2ER Manual de usuario
StarTech.com
StarTech.com S2510BU3PW Manual de usuario
StarTech.com
StarTech.com S2510BU3PW Manual de usuario
StarTech.com
StarTech.com SAT2510BU32 Manual de usuario
StarTech.com
StarTech.com IDECASE18U2B Manual de usuario
