StarTech.com SM21BMU31C3 Manual de usuario

Manual Revision: 06/20/2019

User Manual

For the latest information and specications visit

www.startech.com/SM21BMU31C3

M.2 NGFF SATA Enclosure | USB 3.1 (10Gbps)

Actual product may vary from photos

SKU#: SM21BMU31C3

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Compliance Statements

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit dierent from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du

Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other

Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and

other protected names and/or symbols of third-party companies not related in

any way to StarTech.com. Where they occur these references are for illustrative

purposes only and do not represent an endorsement of a product or service

by StarTech.com, or an endorsement of the product(s) to which this manual

applies by the third-party company in question. Regardless of any direct

acknowledgement elsewhere in the body of this document, StarTech.com

hereby acknowledges that all trademarks, registered trademarks, service marks,

and other protected names and/or symbols contained in this manual and

related documents are the property of their respective holders.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Safety Statements

Safety Measures

• Wiring terminations should not be made with the product and/or electric

lines under power.

• Cables (including power and charging cables) should be placed and routed

to avoid creating electric, tripping or safety hazards.

Mesures de sécurité

• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit

et/ou les câbles électriques sont sous tension.

• Les câbles (y compris les câbles d’alimentation et de chargement) doivent

être placés et acheminés de façon à éviter tout risque électrique, de chute ou

de sécurité

安全対策

• 電源が入っている状態の製品または電線の終端処理を行わないでくださ

い。

• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し

を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう

にしてください。

Misure di sicurezza

• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le

linee elettriche sotto tensione.

• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati

e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o

pericoli per la sicurezza.

Säkerhetsåtgärder

• Montering av kabelavslutningar får inte göras när produkten och/eller

elledningarna är strömförda.

• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så

sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Table of Contents

Compliance Statements........................................................................1

Safety Statements..................................................................................2

Product Diagram....................................................................................4

Front View.................................................................................................................................................... 4

Internal View ............................................................................................................................................... 5

Product Information..............................................................................6

Package Contents ..................................................................................................................................... 6

Requirements ............................................................................................................................................. 6

Installing a Hard Drive...........................................................................7

Connecting the Hard Drive Enclosure ................................................8

Formatting a Hard Drive .......................................................................9

Disconnecting a Hard Drive..................................................................10

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Product Diagram

Front View

1Drive Tray Screw

2USB 3.1 Micro-B Port

3Drive Tray Screw

123

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Internal View

1M.2 NGFF Key B Drive Connector

2Drive Length Adjustable Holes (x 4)

3Drive-Mount Hardware (Screw and

Stando)

123

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Product Information

Package Contents

• M.2 NGFF SATA Enclosure - USB 3.1 x 1

• USB C to Micro B Cable x 1

• Assembly Screws x 4

• Set of M.2 Drive-Mount Hardware x 1

• Screwdriver x 1

• User Manual x 1

Requirements

System requirements are subject to change. For the latest

requirements, please visit www.startech.com/SM21BMU31C3.

• An available USB connector

• An M.2 NGFF SATA Solid State Drive (SSD)

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Installing a Hard Drive

Warning! Hard Drives should be handled carefully, especially

when they’re transported. If you’re not careful with your

drives, you may lose data as a result. Make sure that you are

properly grounded by wearing an anti-static strap when you

install any computer component. If an anti-static strap isn’t

available, touch a large grounded metal surface for several

seconds to discharge any built-up static electricity.

1. Using the Screwdriver (included), remove the two Drive

Tray Screws from the Faceplate.

2. Slide the Drive Tray out of the Hard Drive Enclosure.

3. Place your Hard Drive next to the Drive Tray measuring the

length of the Hard Drive to determine the Drive Length

Hole that match the length of the Hard Drive (30, 42, 60 or

80 mm).

4. Place the Mounting Hardware (Stando) and Nut in the

Drive Length Hole that matches the length of the Hard

Drive and tighten them.

5. Gently slide the M.2 Connector on the Hard Drive into the

M.2 Connector on the Hard Drive Enclosure.

Note: The connector on your drive is keyed so that it only ts

one way.

6. Gently press the Hard Drive down aligning it with the

Stando.

7. Place the Screw into the Stando and tighten the screw to

secure the Hard Drive in place.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

8. Slide the Drive Tray back into the Hard Drive Enclosure so

that the USB 3.1 Micro-B Connector is facing outward.

9. Place the Faceplate over the Connector.

10. Secure the Faceplate in place by inserting two Drive Tray

Screws on either side of the USB 3.1 Micro-B Port on the

front of the Hard Drive Enclosure and use the Screwdriver

to tighten the Drive Tray Screws.

Connecting the Hard Drive Enclosure

Note: The Hard Drive Enclosure does not require an exter-

nal power supply, as it receives enough power through the

USB port on the Host Computer.

After you have installed a Hard Drive in the Hard Drive

Enclosure:

• Connect the USB C to Micro B Cable (included) to the USB

3.1 Micro-B Port on the Hard Drive Enclosure and to a USB

3.1 port on the Host Computer. The Host Computer’s OS

will automatically install the necessary drives.

Note: Before you use the Hard Drive, you need to format it

according to the requirements of your OS. For more informa-

tion about how to do so, see the Formatting a Hard Drive

section.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Formatting a Hard Drive

If you install a Hard Drive that already has data on it, after

you insert the Hard Drive, it appears under My Computer or

Computer with a drive letter assigned to it. If you install a

brand-new Hard Drive that doesn’t contain any data, you must

format the Hard Drive.

If you use a computer that is running a version of Windows®,

complete the following:

1. On the taskbar, click the Windows icon.

2. In the Search eld, type Disk Management.

3. In the search results, click Disk Management.

4. A dialog window appears that asks you to initialize the Hard

Drive. Depending on the version of Windows that you are

running, you have the option to create either an MBR or a

GPT disk.

Note: GPT (GUID partition) is required for drives that are

larger than 2 TB, but GPT isn’t compatible with some earlier

versions of operating systems. MBR is supported by both

earlier and later versions of operating systems.

5. Locate the disk that is labeled Unallocated. To conrm that

the drive is the correct one, check the drive capacity.

6. Right-click the section of the window that says Unallocated

and click New Partition.

7. To initialize the drive in the format of your choice, complete

the on-screen instructions.

Tabla de contenidos

Otros manuales de Recinto de StarTech.com

StarTech.com

StarTech.com InfoSafe IDECASE25OTG Manual de usuario

StarTech.com

StarTech.com SAT2510BU2E Manual de usuario

StarTech.com

StarTech.com SAT3550ESR Manual de usuario

StarTech.com

StarTech.com S251BU31C3CB Manual de usuario

StarTech.com

StarTech.com SATSAS225ODD Manual de usuario

StarTech.com

StarTech.com S2510BU33PW Manual de usuario

StarTech.com

StarTech.com IDECASE35U2B Manual de usuario

StarTech.com

StarTech.com S251BPU31C3 Manual de usuario

StarTech.com

StarTech.com SAT2510BU3 Manual de usuario

StarTech.com

StarTech.com SAT2510U2F Manual de usuario

StarTech.com

StarTech.com S251BRU31C3 Manual de usuario

StarTech.com

StarTech.com ESATCASE2 Manual de usuario

StarTech.com

StarTech.com 8STS25SLOTR Manual de usuario

StarTech.com

StarTech.com SATBP125VP Manual de usuario

StarTech.com

StarTech.com SAT3510U3VP Manual de usuario

StarTech.com

StarTech.com SAT3510BU3 Manual de usuario

StarTech.com

StarTech.com SAT3520U2R Manual de usuario

StarTech.com

StarTech.com RK1224WALHM Manual de usuario

StarTech.com

StarTech.com SAT2510U2REM Manual de usuario

StarTech.com

StarTech.com MONSTADJD Manual de usuario

StarTech.com

StarTech.com S351BMU33ETG Manual de usuario

StarTech.com

StarTech.com IDECASE18U2B Manual de usuario

StarTech.com

StarTech.com InfoSafe S252U2ERR Manual de usuario

StarTech.com

StarTech.com S2510SM12U33 Manual de usuario

Manuales populares de Recinto de otras marcas

SilentiumPC

SilentiumPC Armis AR5 Manual

Pulsar

Pulsar 17/TRP80/DSPR Manual de usuario

Thermaltake

Thermaltake V150 TG Manual de usuario

MSI

MSI MPG SEKIRA 500X Manual de usuario

Antec

Antec Dark fleet DF-10 Manual de usuario

Nexans

Nexans WTC05 Manual de usuario

Peavey

Peavey DS 1502 Manual de usuario

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manual de usuario

Rosewill

Rosewill RX82-U(JBOD) Manual de usuario

QNAP

QNAP SAS JBOD CLI 1.0 Manual de usuario

GAMDIAS

GAMDIAS Talos P1 Manual de usuario

Auvs

Auvs KR615 Manual de usuario

Digitus

Digitus DA-71114 Manual de usuario

CommScope

CommScope FDH 3000 Manual de usuario

FS FHD-FWME4 Manual de usuario

JBL

JBL CS1215T Manual de usuario

Pulsar

Pulsar ARAD-S4 Manual de usuario

Pulsar

Pulsar AWO454 Manual de usuario