StarTech.com SDOCK2U33EB Manual de usuario
Manual Revision: 08/31/2016
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SDOCK2U33EB
USB 3.0/eSATA Dual 2.5/3.5” SATA HDD
Dock with UASP
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Overview ..................................................................................1
Front View .................................................................................................................................................... 1
Rear View...................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Installation ..............................................................................................3
Docking Station Installation.................................................................................................................. 3
Drive Installation ....................................................................................................................................... 3
Drive Removal.........................................................................................4
Docking Station Operation...................................................................5
Drive Initialization .................................................................................................................................... 5
LED Indicator .............................................................................................................................................. 6
Disconnecting the Hard Drive.............................................................................................................. 6
Specications..........................................................................................7
Technical Support ..................................................................................8
Warranty Information............................................................................8
Instruction Manual
1
Product Overview
Front View
Rear View
USB 3.0 port
eSATA port
Power adapter port
Power button
Power /Activity LEDs
HDD/SSD Slot #1
HDD/SSD Slot #2
HDD1 Eject Button
HDD2 Eject Button
Instruction Manual
2
Introduction
Packaging Contents
• 1 x USB 3.0/eSATA to Dual 2.5/3.5in SATA hard drive docking station
• 1 x USB 3.0 Cable
• 1 x eSATA cable
• 1 x universal power adapter (NA/JP, EU, UK, ANZ)
• 1 x instruction manual
System Requirements
• Computer system with available USB or eSATA port
• Up to two 2.5” or 3.5” SATA Hard Drives (HDD) or Solid State Drives (SSD)
• Microsoft® Windows® 2000/XP/Server 2003/Vista/Server 2008 R2/7/8/8.1 (32/64-bit),
Apple® Mac® OS 9.x/10, Chrome OS or Linux®
Instruction Manual
3
Installation
WARNING! Hard drives and docking stations require careful handling. If you are not
careful with your hard disk, lost data may result. Always handle your hard drive and
docking station with caution. Be sure that you are properly grounded by wearing an
anti-static strap when handling computer components or discharge yourself of any
static electricity build-up by touching a large grounded metal surface (such as the
computer case) for several seconds.
Docking Station Installation
1. Connect the Dock to an available power outlet, using the provided power adapter.
2. Connect the Dock to your computer system, using the provided USB/eSATA cable.
Drive Installation
1. Carefully align and insert the 2.5” or 3.5” SATA drive(s) you wish to dock in the
desired hard drive slot on the docking station, such that the SATA power and data
connectors on the drive are properly aligned with the corresponding connectors
inside the hard drive slot.
2. Press the power button so the docking station is turned on.
Note: The single power button operates both drive slots.
Instruction Manual
4
3. Once the drives have been installed and the docking station has been powered on,
the computer Operating System will automatically recognize the drive(s) and it will
be accessible as though it were installed in the system internally.
Note: If your computer fails to automatically recognize your drive it is likely your
drive has not been initialized or formatted correctly. (See Drive Initialization in
Software operation for further instructions.)
Drive Removal
WARNING! Ensure your hard drive(s) has been disconnected from your computer
operating system prior to attempting drive removal. Failure to properly disconnect
your drive may result in lost data or drive damage. (See Disconnecting the Hard Drive
in Docking Station Operation for further instructions.)
1. Turn o the docking station by pressing the power button.
2. Press the eject button that corresponds with the drive you wish to remove.
3. Carefully grasp the ejected drive and lift it upwards until the bottom of the drive has
completely risen above the hard drive slot.
4. Safely and carefully store your drive in a secure location. (See your hard drive
manual for proper storage instructions.)
Note: We recommend ensuring the docking station is powered o before any drive
is physically inserted or removed from the docking station. If two drives are docked
simultaneously, and one drive is removed while the docking station is still powered
on the other drive will momentarily disconnect from your computer which could
cause drive damage or loss of data if other drive is still mounted.
Instruction Manual
5
Docking Station Operation
Drive Initialization
Prior to using your installed drive, it will need to be initialized and formatted to the
operating system requirements in order for your computer system to recognize it.
1. From the main Windows desktop, right-click on “My Computer”(“Computer” in Vista/
7 / 8/ 8.1), then select Manage. In the new Computer Management window, select
Disk Management from the left window panel.
2. A dialog window will automatically appear, asking you to initialize the drive.
Depending on the version of Windows, it will give you the option of either creating
an “MBR” or “GPT” disk.
Note: GPT (GUID partition) is required for drives larger that 2TB but is not
compatible with some older operating systems, while MBR is supported by newer
and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard
drive capacity to conrm it’s the correct hard drive) and then right-click in the
section that says “Unallocated” and select“New Partition”.
Instruction Manual
6
4. Follow the on screen prompts to initialize the drive in the format of your choice.
LED Indicator
The docking station oers an LED indicator for each drive, to enable you to monitor
drive activity. When the docking station is powered on, the LED will illuminate. While
the hard drive is being accessed, the LED will blink. Do not remove your drive from the
docking station while the LED is ashing, as it could damage to your drive, resulting in
data loss.
Disconnecting the Hard Drive
Windows
1. Select the “Safely remove Hardware and Eject Media”icon, located in the task bar.
2. Select the storage device from the list that appears.
3. Wait for the message indicating that it is now safe to remove the device.
Note: Removing the connected drive prior to receiving notication that it is safe to
do so, could result in losing or corrupting data stored on the drive. Once the Safe
to Remove Hardware message appears, please remove the drive from the docking
station. (See Drive Removal.)
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows
listing the contents of the removable drive. Once all windows are closed, click on the
USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop.
Allow 5 seconds before physically removing the drive from the docking station.
Instruction Manual
7
Specications
Host Interface USB 3.0
eSATA
External Connectors 1 x USB 3.0 B female
1 x eSATA female
Internal Connectors 2 x SATA DATA (7 pin) + Power (15 pin)
reciprocal
Maximum Data Transfer Rate USB 3.0: 5Gbit/s
eSATA: 6Gbit/s
Compatible Operating Systems
Windows 2000/XP/Server 2003/Vista/Server
2008 R2/7/8/8.1 (32/64-bit), Mac OS 9/10,
Linux, Chrome OS
Tabla de contenidos
Otros manuales de Estación de acoplamiento de StarTech.com
StarTech.com
StarTech.com DK30C2DPPD Manual de usuario
StarTech.com
StarTech.com USB5N1DOCK Manual de usuario
StarTech.com
StarTech.com SDOCK2U313R Manual de usuario
StarTech.com
StarTech.com ST4300U3C1 Manual de usuario
StarTech.com
StarTech.com 8STUSB3DDOCKFT Manual de usuario
StarTech.com
StarTech.com SDOCK1EU3P Manual de usuario
StarTech.com
StarTech.com InfoSafe SATDOCKU2GB Manual de usuario
StarTech.com
StarTech.com USB3SMDOCKV Manual de usuario
StarTech.com
StarTech.com 129N-USBC-KVM-DOCK Manual de usuario
StarTech.com
StarTech.com SATDOCK22U3S Manual de usuario
StarTech.com
StarTech.com DKWG30DPHPD Manual de usuario
StarTech.com
StarTech.com USB3SMDOCKV Manual de usuario
StarTech.com
StarTech.com SATADOCK22UE Manual de usuario
StarTech.com
StarTech.com DK30BACDD Manual de usuario
StarTech.com
StarTech.com TB3DK2DPW Manual de usuario
StarTech.com
StarTech.com USB3SDOCKHDV Manual del sistema
StarTech.com
StarTech.com DK31C4DPPD Manual de usuario
StarTech.com
StarTech.com SDOCK2U33V Manual de usuario
StarTech.com
StarTech.com USB3SDOCKDD Manual de usuario
StarTech.com
StarTech.com TBDOCKHDPBC Manual de usuario
