SolarEdge SE330K Manual de usuario

SE330K Inverter

Quick Installation Guide

PN: SExxx-xxxxxxxxx

For North America

Version 1.0

Full installation

guide

NOTE

This symbol denotes information intended to assist the user

in making optimum use of the product.

CAUTION!

Denotes a hazard. It calls attention to a procedure that, if

not correctly performed or adhered to, could result in

damage or destruction of the product. Do not proceed

beyond a caution sign until the indicated conditions are

fully understood and met.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if

not correctly performed or adhered to, could result in

injury or loss of life. Do not proceed beyond a warning

note until the indicated conditions are fully understood

and met.

Do not cut the cable connectors

Do not bend the cable. Bending radius: 4 x wire diameter.

This symbol appears at grounding points on the SolarEdge

manuals and equipment.

Legend

Turn ON/OFF the main circuit board AC switch.

When turning it off, wait 5 minutes for DC

Voltage to drop to a safe level before removing

the front panel.

Turn the DC Disconnect Switch on/off. (Switch is

available for some models)

When turning it off, wait 5 minutes for DC

Voltage to drop to a safe level before removing

the front panel.

Turn the ON/OFF/P Switch on/off. When turning

it off, wait 5 minutes for DC Voltage to drop to a

safe level before removing the front panel.

Before connecting aluminum wires to terminals:

1. Remove oxide from the exposed wires with emery paper or a

steel wire brush

2. Clean dust with a cloth and Isopropyl alcohol (IPA)

3. Coat wires with a designated antioxidant aluminum wire

grease immediately after cleaning

CAUTION! Connection of oxidized aluminum wires may result

in resistance and high temperatures at contact points.

Improper execution of the following procedure may cause

damage to the unit.

SAVE THESE INSTRUCTIONS –This manual contains important instructions for the SE330K Inverter that should be followed during

installation and maintenance. Using this equipment in a manner not specified in this guide by SolarEdge may impair the protection provided

by this equipment.

P 1 0

OFF (0)

P 1 0

ON (1)

OFF

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, you are encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

FCC Compliance

Use SolarEdge Designer

to create and design SE system

https://designer.solaredge.com

MAN-01-00XXX-1.0 1

Download SolarEdge Mapper

to map string Power Optimizers

Installing the Power Optimizers 1

Create a new site in Monitoring

Platform and import PV layout

from SolarEdge Designer

https://monitoring.solaredge.com

/solaredge-web/p/login

124563

Download

Scan QR code using Mapper

Complete site registration and

physical layout in the

Monitoring platform

2 MAN-01-00XXX-1.0

Installing the Power Optimizers

1123456

¼” / M6

Stainless steel 84 lb*in / 9.5 N*m

0.5” / 12.7 mm

0.4“ / 10 mm

OUT IN

0.4“ / 10 mm

Install the H1300 Power Optimizer

MAN-01-00XXX-1.0 3

Connecting the Power Optimizers 1

123456

CAUTION! Do not sharply bend the DC cables. Keep proper bending

radius to avoid cable break. Do not use stretched cabling. Using only

MC4 connectors compatible with the Power optimizer.

OUT IN

Combiner Box

4 MAN-01-00XXX-1.0

Connecting PV Strings

To minimize electromagnetic interference (EMI), make sure to

minimize the distance between the positive and negative DC cables

Max distance between a combiner

box and any string: 150m / 492ft

Max distance between inverter

and combiner box: 700m / 2297ft

Combiner Box

Turn off switches and check

string polarity. Verify 1±0.1V

per optimizer.

Example: 20 optimizers = ~20V

20V

When connecting three or

more H1300 strings to a

combiner box, it is

recommended to use a 30A

fuse for each individual

string. However, be sure to

check local electrical codes

and regulations to

determine the proper fuse

sizing for your specific

installation.

MAN-01-00XXX-1.0 5

Maintaining Clearance 3

CAUTION! Do not block Airflow

Min Indoor Clearance

903 mm

CAUTION! Install more than 50m from a saline environment

Back-to-back Clearance

Front Clearance

WARNING! The area in front

of the inverter must be kept

clear for at least 36” / 915 mm

19.7" /

500 mm

19.7" /

500 mm

39.4“ / 1000 mm

42.9” / 1090 mm

35.5” / 903 mm

16.38” / 416 mm 15.75” / 400 mm

19.7" / 500 mm to 39.4“ / 1000 mm

36" / 915 mm

Min Outdoor Clearance

7.87” / 20 cm where annual average high temperature equals or below 77˚F / 25˚C

It is recommended not

to install the inverter

directly under the sun

Mounting

6 MAN-01-00XXX-1.0

342 lb

155 KG

40.39“ / 1026 mm

36.46" / 926 mm

Ø 1/2“ /

13 mm

28.98" / 736 mm

7.28" /

185 mm

7.24" /

184 mm

7.24" /

184 mm

7.24" /

184 mm

3.93 /

105 mm

7.24" /

184 mm

WARNING

DISCONNECT POWER BEFORE REMOVING COVERS

MAN-01-00XXX-1.0 7

Removing Covers, Drilling Holes, and Grounding Conduits 5

OFF

P 1 0 OFF (0)

OFF

321

1.9 lb*ft

Use center drill guides on panels

CAUTION! Remove panels

from inverter before drilling holes

Otros manuales para SE330K

Tabla de contenidos

Otros manuales de Inversor de SolarEdge

SolarEdge

SolarEdge StorEdge SE5K-RWS Manual de usuario

SolarEdge

SolarEdge SE K Series Manual de usuario

SolarEdge

SolarEdge Solar Inverter Manual de usuario

SolarEdge

SolarEdge SE3000 Manual de usuario

SolarEdge

SolarEdge SE50K Manual de usuario

SolarEdge

SolarEdge StorEdge Interface SESTI-S4 Manual de usuario

SolarEdge

SolarEdge Power Harvesting System Manual de usuario

SolarEdge

SolarEdge StorEdge SE5000H-O4 Manual de usuario

SolarEdge

SolarEdge SE2200 Manual de usuario

SolarEdge

SolarEdge T568B Manual de usuario

SolarEdge

SolarEdge storedge Manual de usuario

SolarEdge

SolarEdge Home Battery 48V Manual de usuario

SolarEdge

SolarEdge SEK-AU I Series Manual de usuario

SolarEdge

SolarEdge SE15K Manual de usuario

SolarEdge

SolarEdge SE K Series Manual de usuario

SolarEdge

SolarEdge Energy Bank Manual de usuario

SolarEdge

SolarEdge SE K Series Manual de usuario

SolarEdge

SolarEdge SE3680H Manual de usuario

SolarEdge

SolarEdge 3000A-US Manual de usuario

SolarEdge

SolarEdge SE3K Manual de usuario

SolarEdge

SolarEdge SE15K-AU Manual de usuario

SolarEdge

SolarEdge SE3000 Manual de usuario

SolarEdge

SolarEdge SEK-I Series Manual de usuario

SolarEdge

SolarEdge SEXXXXH-RWMBNBF54 Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario