SolarEdge Energy Bank Manual de usuario
Installation Guide
SolarEdge Home Hub
Inverter Single Phase
For Australia
Version 1.5
Disclaimers
Important Notice
Copyright © SolarEdge Inc. All rights reserved.
No part of this document may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photographic,
magnetic or otherwise, without the prior written permission of SolarEdge Inc.
The material furnished in this document is believed to be accurate and reliable.
However, SolarEdge assumes no responsibility for the use of this material. SolarEdge
reserves the right to make changes to the material at any time and without notice. You
may refer to the SolarEdge web site (www.solaredge.com) for the most updated version.
All company and brand products and service names are trademarks or registered
trademarks of their respective holders.
Patent marking notice: see http://www.solaredge.com/patent
The general terms and conditions of delivery of SolarEdge shall apply.
The content of these documents is continually reviewed and amended, where
necessary. However, discrepancies cannot be excluded. No guarantee is made for the
completeness of these documents.
The images contained in this document are for illustrative purposes only and may vary
depending on product models.
This manual describes installation of theSolarEdge Home Hub Inverter. Read this
manual before you attempt to install the product, and follow the instructions
throughout the installation process. If you are uncertain about any of the requirements,
recommendations, or safety procedures described in this manual, contact SolarEdge
Support immediately for advice and clarification. The information included in this
manual is accurate at the time of publication. However, the product specifications are
subject to change without prior notice. In addition, the illustrations in this manual are
meant to help explain system configuration concepts and installation instructions. The
illustrated items may differ from the actual items at the installation location.
Disclaimers1
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
Revision History
Version 1.5 (April 2023)
LG Chem Prime Battery removed.
Version 1.4 (October 2022)
Updated name to SolarEdge Home Hub Inverter Single Phase
Version 1.3 (January 2021)
Added S-series Power Optimisers installation guidelines in
Installation Guidelines
on
page 14.
Added the option to use Opti Clamps in
Step 1: Mounting the Power Optimisers
on
page 17.
Version 1.2 (October 2021)
Editorial changes
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
2 Revision History
Contents
Disclaimers 1
Important Notice 1
Revision History 2
HANDLING AND SAFETY INSTRUCTIONS 5
Safety Symbols Information 5
IMPORTANTSAFETYINSTRUCTIONS 6
Chapter 1: Overview 9
SolarEdge Home Battery Solution Components 9
List of Installation Equipment 10
Inverter Transport and Storage 11
Chapter 2: Installing the Power Optimisers 12
Safety 12
Installation Guidelines 14
Step 1: Mounting the Power Optimisers 17
Step 2: Connecting a PV module to a Power Optimiser 18
Step 3: Connecting Power Optimizers in Strings 19
Step 4: Verifying Proper Power Optimiser Connection 20
Chapter 3: Installing the Inverter 21
Inverter Package Contents 21
Identifying the Inverter 21
Unpacking the inverter 21
Inverter Interfaces 22
Mounting the Inverter 26
Selecting a Residual Current Device (RCD) 29
Chapter 4: Installing the Battery (Optional) 31
Chapter 5: Connecting the Inverter 32
Installing Conduits 32
Connecting the Inverter to ACGrid 33
Connecting the DC Strings to the Inverter 33
Connecting the Battery (Optional) 35
Connecting the Backup Interface 36
Connecting an External CTto the Energy Meter (Optional) 37
Connecting an External RSDSwitch (Optional) 38
Installing the 9V Battery 40
Connecting Multiple Inverters through RS485 41
Chapter 6: Activating, Commissioning and Configuring the System 43
Step 3: Verifying Proper Activation and Commissioning 46
Revision History3
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
Configuring Communication with Other Devices 47
Running a Battery Self-test 47
Enabling Home Hub Applications 48
Enabling Demand Response Mode for Zero Export 49
Reporting and Monitoring Installation Data 50
Chapter 7: Setting Up Communication with the Monitoring Platform 53
Communication Options 53
Communication Connectors 55
Removing the Inverter Cover 56
Creating an Ethernet (LAN) Connection 57
Verifying the Connection 59
Appendix A: Errors and Troubleshooting 60
Identifying Errors 60
Energy Hub Inverter Troubleshooting 61
Troubleshooting Communication 62
Power Optimiser Troubleshooting 63
Appendix B: Mechanical Specifications 65
Appendix C: SafeDC™ 66
Support Contact Information 67
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
4 Revision History
HANDLING AND SAFETY INSTRUCTIONS
Safety Symbols Information
The following safety symbols are used in this document. Familiarize yourself with the
symbols and their meaning before installing or operating the system.
WARNING!
Denotes a hazard. It calls attention to a procedure that, if not correctly
performed or adhered to, could result in injury or loss of life. Do not proceed
beyond a warning note until the indicated conditions are fully understood and
met.
CAUTION!
Denotes a hazard. It calls attention to a procedure that, if not correctly
performed or adhered to, could result in damage or destruction of the
product. Do not proceed beyond a caution sign until the indicated conditions
are fully understood and met.
NOTE
Denotes additional information about the current subject.
IMPORTANTSAFETYFEATURE
Denotes information about safety issues.
Disposal requirements under the Waste Electrical and Electronic Equipment (WEEE)
regulations:
NOTE
Discard this product according to local regulations or send it back to SolarEdge.
HANDLING AND SAFETY INSTRUCTIONS5
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
IMPORTANTSAFETYINSTRUCTIONS
SAVETHESEINSTRUCTIONS
Warning!
To reduce the risk of injury, read all instructions in this document.
WARNING!
Before opening the inverter cover:
1. Turn off the inverter ON/OFF/P switch located at the bottom of the inverter.
2. Turn off the Connection Unit DCsafety switch (if applicable).
3. Turn off the inverter ACcircuit breaker on the main service panel.
4. Wait five minutes for the capacitors to discharge.
WARNING!
Before operating the inverter, ensure that the inverter AC power cable and wall
outlet are grounded properly. This product must be connected to a grounded,
metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment grounding
terminal or lead on the product.
WARNING!
Opening the inverter and repairing or testing under power must be performed
only by qualified service personnel familiar with this inverter.
WARNING!
Do not touch the PV panels or any rail system connected when the inverter
switch is ON, unless grounded.
WARNING!
SafeDC complies with IEC60947-3 when installing the system with a worst case
SafeDC voltage (under fault conditions) < 120V.
The worst case voltage is defined as: Voc,max+ (String Length-1)*1V, where:
Voc,max = Maximum Voc (at lowest temperature) of the PV modules in the
string (for a string with multiple modules, use the max value)
String Length = number of power optimisers in the string
CAUTION!
This unit must be operated according to the technical specification datasheet
provided with the unit.
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
6 IMPORTANTSAFETYINSTRUCTIONS
CAUTION!
HEAVY OBJECT. To avoid muscle strain or back injury, use proper lifting
techniques, and if required - a lifting aid.
NOTE
The Connection Unit is NEMAtype 3R rated . Unused glands should be sealed
with appropriate seals.
NOTE
Use PV modules rated according to IEC 61730 class A.
NOTE
The symbol appears at grounding points on the SolarEdge equipment. This
symbol is also used in this manual.
NOTE
The following warning symbols appear on the inverter warning label:
Risk of electric shock
Risk of electric shock from energy stored in the capacitor. Do
not remove cover until 5 minutes after disconnecting all
sources of supply.
Hot surface – To reduce the risk of burns, do not touch.
Caution, risk of danger
WARNING!
Before operating the system, ensure that the been grounded properly.
WARNING!
When handling the storage system battery, adhere to all manufacturer safety
instructions.
CAUTION!
This unit must be operated under the specified operating conditions as
described in the technical specifications supplied with the unit.
NOTE
The batteries must be certified according to local regulations and supported by
the SolarEdge inverter firmware.
IMPORTANTSAFETYINSTRUCTIONS 7
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
NOTE
For battery decommissioning and disposal, follow the manufacturer
requirements and instructions.
NOTE
Multiple inverter combination is not supported.
NOTE
The Home Hub Interface is IP65 rated. Unused connectors and glands should
be sealed with the provided seals.
NOTE
For inverters with a nameplate up to and including 10kW:
Maximum short circuit peak current: 78.1A
Maximum short circuit current duration (until current stops): 113msec
Maximum 3-cycle short circuit current RMS value: 60A
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
8 IMPORTANTSAFETYINSTRUCTIONS
Chapter 1: Overview
NOTE
Backing up high-consumption loads, such as whole home air conditioners and
well pumps, requires installation of a soft start device (not supplied by
SolarEdge) on the AC supply of these loads.
SolarEdge Home Battery Solution Components
SolarEdge Home Hub Inverter Single Phase - manages battery and system
energy, in addition to its traditional functionality as a DC-optimized PV inverter.
The Connection Unit, located at the bottom of the inverter, allows simple
installation and connectivity to other system components and includes an external
DC Safety Switch.
The Energy Meter is used by the inverter for export, import, and consumption
readings, and for Smart Energy Management applications, such as export limitation,
time-of-use profile programming and maximizing self-consumption.
One or multiple batteries (optional) - DC-coupled batteries designed to work with
the SolarEdge system. The batteries can be connected to the system optionally.
When installing a battery, connect the DC cables from the battery and from Power
Optimisers to an external combiner box, compliant with local regulation. Then,
connect the cables from the combiner box to the DCterminals inside the inverter's
Connection Unit.We recommend using the SolarEdge combiner box. For
installation and connection instructions see:
https://www.solaredge.com/sites/default/files/se-combiner-box-installation-guide-
aus.pdf
Chapter 1: Overview9
SolarEdge Home Hub Inverter Single Phase MAN-01-00812-1.5
Otros manuales para Energy Bank
1
Tabla de contenidos
Otros manuales de Inversor de SolarEdge
SolarEdge
SolarEdge BI-EU1P Manual de usuario
SolarEdge
SolarEdge SE K Series Manual de usuario
SolarEdge
SolarEdge SE8K-N4 Manual de usuario
SolarEdge
SolarEdge StorEdge SE5K-RWS Manual de usuario
SolarEdge
SolarEdge 2.2KW Manual de usuario
SolarEdge
SolarEdge Home Battery 48V Manual de usuario
SolarEdge
SolarEdge Energy Bank Manual de usuario
SolarEdge
SolarEdge storedge Manual de usuario
SolarEdge
SolarEdge SE K Series Manual de usuario
SolarEdge
SolarEdge SE8k Manual de usuario
SolarEdge
SolarEdge SE K Series Manual de usuario
SolarEdge
SolarEdge Inline Energy Meter Manual de usuario
SolarEdge
SolarEdge SE12.5k Manual de usuario
SolarEdge
SolarEdge SE3680H Manual de usuario
SolarEdge
SolarEdge EV Series Manual de usuario
SolarEdge
SolarEdge SE3500 Manual de usuario
SolarEdge
SolarEdge storedge Manual de usuario
SolarEdge
SolarEdge storedge Manual de usuario
SolarEdge
SolarEdge SE5000H-AU Manual de usuario
SolarEdge
SolarEdge SE2200 Manual de usuario
