Socket CHS 7Mi Manual de usuario

Model shown: CHS 7Mi

Bluetooth Barcode Scanner

CHS 7Mi/7Pi

www.socketmobile.com

SERIES 7

1D LASER QUICKSTART GUIDE

PACKAGE CONTENTS

SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The Bluetooth

word mark and logo are registered trademarks of the Bluetooth SIG, Inc. USA, and any

use by Socket Mobile, Inc. is under license. All other trademarks and trade names

contained herein may be those of their respective owners.

CHS Series 7

AC adapter* & USB

to DC plug cable

*Use the plug that is region-

ally appropriate

Lanyard

NiMH

rechargeable

batteries

Thank you for choosing Socket Mobile!

Let’s get started!

mobile

Rydbatt 201607

MH-AAA 1.2V 1000 mAh

Rydbatt 201607

MH-AAA 1.2V 1000 mAh

PRODUCT INFORMATION

*Also used for keyboard Pop-up feature (HID Mode only)

Twist-lock

(horizontal/unlocked)

Disc for magnet on

stand charger

Battery door

Twist-lock

(vertical/locked)

Lanyard

Blue/Green/Red

LED

Trigger button

Power button*

DC-in connector

Scanner head

Product label

Pins for

charging

cradle

SCANNER SETUP

Insert the Batteries

Unlock the Battery door by using

a thin coin to turn the lock under

the CHS to a horizontal position (turn 90

degrees).

Install the batteries in their correct position

as indicated by the +/- symbols.

Important: Only use NiMH Recharge-

able batteries. Do NOT use Alkaline

Batteries

Attach the Lanyard (optional)

Detach the string loop of the tether

from the lanyard. Then feed the

string loop through the slot in the Twist-lock

and then through the end of the loop. Pull

tight so the string loop is secure to the Twist-

lock, Reattach the string loop to the tether

from the Lanyard.

If desired, attach the tether to a

lanyard or belt.

Charge the CHS

The CHS must be fully charged before

rst use. Please allow 5 hours uninter-

rupted charging for the initial battery

charge.

For the 7Di or 7DiRx, lift the rubber ap to

access the power connector.

• Red LED = Charging

• Green LED = Fully charged

Charging from a computer USB port is

not reliable and not recommended.

Charging Cradles & Charging QX Stand

available separately.

BASIC FUNCTIONALITY

Powering On:

Press and hold down the small power button until the LED turns blue and the

CHS beeps twice (low-high).

Powering Off/ Disconnecting:

Press and hold down the small power button until the CHS beeps

twice (high-low).

Scanning Barcodes

After connecting the CHS to your device, open an application. Place the cursor

where you want to enter the scanned data.

1. Hold the CHS a few inches from the barcode.

2. Aim, press and hold the trigger button.

By default, the CHS will beep, vibrate, and the LED will ash green to conrm

successful scan.

Not recommended

scanning techniques

Aim the scan beam straight

across the entire barcode.

Power button

Connect your CHS using one of the following Bluetooth modes:

Bluetooth Connection Proles

Bluetooth Mode Description

HID (Default)*

Human Interface

Device Prole

• “NO” software installation needed.

• Connects to most devices.

• Good for barcodes containing small amounts of data.

• Scanner appears like a keyboard.

SPP

Serial Port

Prole

• Software installation required.

• More efcient data communications for barcodes con-

taining lots of data.

iOS

Apple Specic

Serial Prole

• Must use with an App developed to work with

iOS devices

• Apple MFI tested and certied.

• If you have an application that supports Socket Mobile

Scanners this is the mode you want to use.

*By default, the CHS is set to HID Mode.

Operating System Connection Options

Operating

Systems

(OS)

Devices

Bluetooth

HID

Support

Bluetooth

SPP

Support

Bluetooth

Apple Serial

Specic

(iOS Mode)

Android Android 2.1 &

later Yes Yes No

Apple iOS iPod, iTouch,

iPhone, &iPad Yes No Yes

Windows

Mobile

Windows Mobile

6.x Yes Yes No

Windows PC Windows 7, 8 Yes Yes No

Mac OS

Mac OS X 10.4 to

10.X

Mac Books, Mac

Mini, &iMac

Yes No No

Note: To switch from one mode to the other you must remove the

pairing information (see unpairing procedure on page 12) from both

devices - host computer and the CHS.

BLUETOOTH CONNECTION METHODS

HID MODE

Android: Connect Android Device in HID Mode

1. Power on the CHS. Make sure the CHS is discoverable (unpaired).

2. Touch Home | Menu | Settings | Wireless &Networks | Bluetooth

settings

3. Make sure the device has Bluetooth “On”. Scan for devices.

4. In the list of found devices, select Socket CHS [xxxxxx]. Tap Pair.

5. The CHS will connect to the Android device.

6. The CHS will beep once after it has connected and is ready to scan bar-

codes.

*Apple: Connect Apple iOS Device or Mac OS Device HID Mode

In this mode the scanner works and behaves just like a keyboard.

Therefore, CHS will work with Safari, Notes, and any other applications that

supports an active cursor.

1. Power on the CHS. Make sure the CHS is discoverable (unpaired).

2. Start a Bluetooth device search.

• iOS: Tap Settings | General | Bluetooth. Turn on Bluetooth. A

Bluetooth device search will begin.

• Mac OS: Click System Preferences | Internet &Wireless |

Bluetooth. In Bluetooth preferences, select the On checkbox. Click Set up

New Device... A Bluetooth device search will begin.

3. In the device list, tap on CHS [xxxxxx]. Tap Pair.

4. The CHS will connect to the Apple device.

5. The CHS will beep once after it has connected and is ready to scan

barcodes.

*For Apple iOS Keyboard (only for HID mode)

• To enable/disable keyboard pop-up feature, double tap (press) the power

button.

Windows: Connect Windows PC

Power on the CHS. Make sure the CHS is discoverable (unpaired).

1. Use your computer’s Bluetooth Settings to connect to the CHS.

2. Open Devices and Printers and select “Add a device”.

3. In the device list, select Socket CHS [xxxxxx]. Click Next.

4. If a passkey is requested, enter 0000 (four zeroes). Click OK.

Or Pair Now.

5. Follow the remaining screens to complete the wizard.

Note: On some computers the CHS will have to be congured as HID

Peripherals (see next page).

Windows: Connect Windows PC as a HID Peripheral

1. Power on the CHS and scan this barcode. The CHS will beep 3 times.

2. Turn on Bluetooth on your PDA or PC and start a device search.

3. Select Socket CHS. If prompted for a passkey, enter 0000 (four zeroes). If

prompted to select services, select Input Device.

4. After the CHS connects and is ready to scan barcodes, it will beep once.

Now you are ready to scan barcodes!

To connect to a new device, you must rst unpair the CHS See page 12.

WINDOWS HID (PERIPHERALS) MODE

SPP MODE

Connect Android device in SPP mode

Note: SocketScan 10 software installation required.

1. Power on the CHS and scan this barcode. The CHS will beep 3 times.

2. Turn Bluetooth on for your device. Go to Settings >

Bluetooth. A Bluetooth Devices search will begin.

3. Tap Socket CHS[xxxxxx] in the list of Devices found.

After a few seconds the “Not Paired” status will change

to “Connected” and the CHS Blue LED will blink every 3

seconds conrming the connection.

4. Go to Google Play Store, search for “SocketScan 10”.

5. Download &install. Follow the on screen instructions.

6. Open SocketScan 10 application.

7. When prompted to set SocketScan 10 as the keyboard

language, tap Back .

8. Go to phone Settings / Language and Input

9. Under Keyboard Settings, select SocketScan 10.

10.Open SocketScan 10 on your device.

11.Tap the Menu * icon, then select Input Method.

* icon may not be visible. Tap where the menu would normally appear.

12.On the next screen, select SocketScan 10 as input method.

13.Tap the “Set Up Input Method”.

14.In SocketScan 10, tap the Menu * icon then select Socket EZ Pair.

Note: Select SocketScan 10 to congure the keyboard language or congure

the button to a scan trigger button

15. Tap the option “Bluetooth”.

16.Tap Socket CHS[xxxxxx]* from the list of devices found.

17.The CHS will beep once to indicate connected state and is ready to scan

barcodes. Close/exit application.

Now you are ready to scan barcodes!

WINDOWS PC

Connect Windows PC in SPP Mode

Note: Make sure you have administrative privileges.

1. Download the latest SocketScan 10 software from Socket Mobile’s support

web page.

2. Follow the on-screen instructions to install the software.

3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM port.

4. Power on the CHS and scan this barcode. The CHS will beep 3 times.

5. Use the Bluetooth software on your computer to start a device search.

6. Tap Socket CHS[xxxxxx]* in the list of Devices found. If prompted for a

passkey enter 0000 (four zeroes).

*The characters in brackets are the last 6 characters of the Bluetooth address.

See label in the CHS battery compartment

Note: If prompted, please click Ports to create a new incoming COM port in

Bluetooth settings.

7. Follow the remaining screen instructions to complete the process.

8. Click on the SocketScan 10 icon in the system tray. In the

pop-up menu, click Socket EZ Pair.

If the icon does not appear, open SocketScan 10 by clicking on the desktop

shortcut.

9. Select 1D Scanner.

10. Select your CHS in the list and click Pair.

11. After they pair, the computer will connect to the CHS, indicated by a beep.

The CHS will then disconnect, indicated by two beeps. Click OK.

12. After several seconds, the CHS will reconnect to the computer, indicated

by a beep and the icon will also appear in the system tray.

13. Click X to close Socket EZ Pair. The CHS Registration screen will appear.

14. Make sure the CHS is connected to the computer, indicated by the CHS

icon in the system tray.

Now you are ready to scan barcodes!

Otros manuales para CHS 7Mi

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Socket

Socket

Socket 800 SERIES Manual de usuario

Socket

Socket Wand Scanner 2E Manual de usuario

Socket

Socket SocketScan 700 Series Manual de usuario

Socket

Socket CHS 7Mi Manual de usuario

Socket

Socket DuraSled DS800 Series Manual de usuario

Socket

Socket CHS 7Ci Manual de usuario

Socket

Socket DURASCAN D760 Instrucciones de funcionamiento

Socket

Socket Gun Scanner (GS) 2X (Xtreme Performance) Manual de usuario

Socket

Socket CHS Series 7 Manual de usuario

Socket

Socket SOCKETSCAN 800 Series Manual de usuario

Socket

Socket DURASCAN D740 Manual de usuario

Socket

Socket 9M Manual de usuario

Socket

Socket CHS 7M Manual de usuario

Socket

Socket CHS Series 7 Manual de usuario

Socket

Socket CompactFlash Scan Card Series 5 Manual de usuario

Socket

Socket DURASCAN D750 Manual de usuario

Socket

Socket CHS 7Mi Manual de usuario

Socket

Socket CHS 7M Manual de usuario

Socket

Socket SD Scan Card 3E Manual de usuario

Socket

Socket SocketScan 800 Series Manual de usuario

Socket

Socket CHS Series 7 Manual de usuario

Socket

Socket DURACASE 800 Series Manual de usuario

Socket

Socket CHS 7Mi Manual de usuario

Socket

Socket CX2895-1508 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario