Siemens SIMATIC PM-E Manual de usuario

Power module PM-E DC24V (6ES7138-

4CA01-0AA0)

___________________

SIMATIC

ET 200S distributed I/O

Power module PM-E DC24V

(6ES7138-4CA01-0AA0)

Manual

04/2007

A5E01119952

-02

Preface

Properties

Parameters

Diagnostics

Configuring

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E01119952-02

Ⓟ

04/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Manual, 04/2007, A5E01119952-02 3

Preface

Purpose of the manual

This manual supplements the

ET 200S Distributed I/O System

Operating Instructions.

General functions for the ET 200S are described in the ET 200S Distributed I/O System

Operating Instructions (http://support.automation.siemens.com/WW/view/en/1144348).

The information in this document along with the operating instructions enables you to

commission the ET 200S.

Basic knowledge requirements

To understand these operating instructions you should have general knowledge of

automation engineering.

Scope of the manual

This manual applies to this ET 200S module. It describes the components that are valid at

the time of publication.

Recycling and disposal

Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For

environmentally compliant recycling and disposal of your electronic waste, please contact a

company certified for the disposal of electronic waste.

Additional support

If you have any questions relating to the products described in this manual and do not find

the answers in this document, please contact your local Siemens representative

(http://www.siemens.com/automation/partners).

A guide to the technical documentation for the various SIMATIC products and systems is

available on the Internet. (http://www.siemens.com/simatic-docu).

The online catalog and ordering systems are available on the Internet

(http://www.siemens.com/automation/mall).

Training center

We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation

system. Please contact your regional training center or the central training center in

D -90327, Nuremberg, Germany (http://www.siemens.com/sitrain).

Preface

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

4Manual, 04/2007, A5E01119952-02

Technical Support

You can contact Technical Support for all Industry Automation products by means of the

Internet Web form for the Support Request

(http://www.siemens.com/automation/csi_en_WW/support_request).

Additional information about Siemens Technical Support is available on the Internet

(http://www.siemens.com/automation/csi_en_WW/service).

Service & Support on the Internet

In addition to our documentation, we offer a comprehensive knowledge base on the Internet

(http://www.siemens.com/automation/csi_en_WW/support).

There you will find:

●Our Newsletter, which constantly provides you with the latest information about your

products.

●The right documentation for you using our Service & Support search engine.

●The bulletin board, a worldwide knowledge exchange for users and experts.

●Your local contact for Automation & Drives in our contact database.

●Information about on-site services, repairs, spare parts, and lots more.

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Manual, 04/2007, A5E01119952-02 5

Table of contents

Preface ................................................................................................................................................... 3

1 Properties ............................................................................................................................................... 7

1.1 Power module PM-E DC24V (6ES7138-4CA01-0AA0).................................................................7

2 Parameters ........................................................................................................................................... 11

3 Diagnostics ........................................................................................................................................... 13

3.1 Diagnostics using LED display.....................................................................................................13

3.2 Error types....................................................................................................................................14

4 Configuring ........................................................................................................................................... 15

4.1 Configuring the address space ....................................................................................................15

Index..................................................................................................................................................... 17

Table of contents

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

6Manual, 04/2007, A5E01119952-02

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Manual, 04/2007, A5E01119952-02 7

Properties

1.1

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Properties

●The PM-E DC24V power module monitors the supply voltage for all the electronic

modules in the voltage group. The supply voltage is fed in by means of the TM-P terminal

module.

●You can use all the electronic modules except the 2DI AC120V ST, 2DI AC230V ST, and

2DO AC24..230V/1A in the voltage group of the PM-E DC24V power module.

●The current status of the power module is stored in the status byte in the process input

image (PII). This is updated irrespective of whether the "No Load Voltage" diagnosis has

been enabled.

●The PM-E DC24V power module is suitable for fail-safe modules.

●Extended temperature range from 0 to 55°C with vertical installation.

CAUTION

Only connect the specified rated load voltage of 24 VDC to the TM-P terminal module of

the power module.

The connected rated load voltage must correspond to the supply voltage of the

electronic modules in the voltage group.

Maximum configuration per voltage group

The number of modules that can be connected depends on the total current of all modules in

a voltage group. This total must not exceed the maximum current carrying capacity.

Address space of inputs/outputs

Address space of inputs/outputs by selecting the following as an option:

Options

Address space of the inputs

Address space of the outputs

Status byte (S)

1 byte

Option handling (O)

8 bytes

Status byte and option handling

(SO)

9-byte inputs 9 bytes (9th byte not relevant)

Properties

1.1 Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

8Manual, 04/2007, A5E01119952-02

General terminal assignment

Note

Terminals

A4 and A8 are only available at specified terminal modules.

Terminal assignment for PM-E DC24V (6ES7138-4CA01-0AA0)

Terminal

Assignment

Terminal

Assignment

Notes

L+

•L+: Rated load voltage 24 VDC

•M: Chassis ground

•AUX1: Protective-conductor terminal or potential bus (freely usable

up to 230 VAC)

AUX1

Properties

1.1 Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Manual, 04/2007, A5E01119952-02 9

Usable terminal modules

Usable terminal modules for PM-E DC24V (6ES7138-4CA01-0AA0)

TM-P15C23-A1

(6ES7193-

4CC30-0AA0)

TM-P15C23-A0

(6ES7193-4CD30-

0AA0)

TM-P15C22-01

(6ES7193-4CE10-

0AA0)

Spring terminal

TM-P15S23-A1

(6ES7193-

4CC20-0AA0)

TM-P15S23-A0

(6ES7193-4CD20-

0AA0)

TM-P15S22-01

(6ES7193-4CE00-

0AA0)

Screw-type terminal

TM-P15N23-A1

(6ES7193-

4CC70-0AA0)

TM-P15N23-A0

(6ES7193-4CD70-

0AA0)

TM-P15N22-01

(6ES7193-4CE60-

0AA0)

Fast Connect

Block diagram

Figure 1-1 Block diagram of the PM-E DC24V power module

Properties

1.1 Power module PM-E DC24V (6ES7138-4CA01-0AA0)

Power module PM-E DC24V (6ES7138-4CA01-0AA0)

10 Manual, 04/2007, A5E01119952-02

Technical data PM-E DC24V (6ES7138-4CA01-0AA0)

Dimensions and weight

Dimension B (mm)

Weight

Approx. 35 g

Voltages, currents, potentials

Rated load voltage

24 VDC

•Overvoltage protection No

Protection with automatic circuit breakers

Yes, tripping characteristic B, C

Max. current-carrying capacity (up to 60°C)

10 A

•Short-circuit protection No

Electrical isolation

•Between rated load voltage and backplane

bus

Yes

•Between the power modules Yes

Insulation test voltage

500 VDC

Current consumption

•From the load voltage L+ (no load) Max. 4 mA

Power dissipation of the module

Typically 100 mW

Parameter length

3 bytes

Status, interrupts, diagnostics

Diagnostic function

Yes

•Group error Red "SF" LED

•Load voltage monitoring Green "PWR" LED

•Diagnostic information readable Yes

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de Siemens

Siemens

Siemens Simantic ET200SP Guía del usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens FDCIO181-2 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens Simatic CFU Guía de inicio rápido

Siemens

Siemens Simatic S7-1500 Manual de lista de piezas

Siemens

Siemens 6ES7547-1JF00-0AB0 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200eco Manual de usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens DI 8x24VAC/48VUC BA Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Documento técnico

Siemens

Siemens SIMATIC ET 200AL Guía del usuario

Siemens

Siemens SIM-16 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario