Siemens FDCIO181-2 Manual de usuario

BuildingTechnologies

Firesafetyandsecurityproducts

FDCIO181-2 Input/OutputModule

ProductManual

Characteristic

lMicroprocessor-controlled signalevaluation

lAutomaticaddresssetting, without encoder settingsor DIPswitch

l2monitored input, 2monitored output

lLEDdisplayofinput andoutputstatus

lInputlinesmonitored for openlineor short circuit

lPreventionofnoiseinterferencethroughintelligent analysisofinput signals

lOutputlinesmonitored for openlineorshort circuit (whenpotentialoutput andnot activated)

lOutput monitoringconfigurable(on/off)

lControloutput for equipment 24 VDC,max. 2A

lPower supplyviaFD18-BUS

lCommunicationwithcontroller viaFD18-BUS(detector line)

lDirectlyused indryareas. Applicableindustyand humidareaswheninstalled inhousing

lSticker Method”easyfor commissioning

BuildingTechnologies A6V10214492_a_en_--

Firesafetyandsecurityproducts 03.2010

Application

Input

Withtheinput astatuscanbe monitored, theinput canbe configured bycontroller or

configurationtoolsasfollows:

lStatus input or Alarm input

lLead monitoring for open line or open line and short circuit

lWhen inputting status, according todifferent statusof contact, can be set asfallows:

–Normalmode: normallyopenNO input

–Inverted mode: normallyclosed NO input

Fig. 1connectiondiagramofdrycontactinput

Status inputs and alarm inputs

Alarm inputstrigger analarmassoonastheinput isactivated. Status inputstrigger a

monitoringstatuschange assoonastheyare activated.

Linemonitoringandcircuitry

Theinputlinesare monitored for openlineor openlineand short circuit. Tomakethese

possible, resistorsmust be properlyconnected totheendoflinesoftheinput (Fig. 1).When

anopenlineor ashort circuit occursononeoftheinput lines, afault message istransmitted

tothecontrolpanel. Theinput must be potential-free.

Output

External poweroutput(Default)

Normaloperation (outputlinesmonitored)

-Beused for controlling(e.g. operatingahorn/strobe).

-Themoduleswitchestheexternallysupplied 24 VDC voltage inactivestatusonthe

output.

-Ininactivestatustheoutputlineismonitored for openlineandshort circuit(Fig. 3).

-Thejumper ontheinput/output modulemust be plugged ontoJ2/J4(Fig. 2)

Fig.2Input/output modulejumper positionJ2, J4

Fig.3Connectionfor normaloperationwithoutput linemonitored for short circuit and openline

1N5404

BuildingTechnologies A6V10214492_a_en_--

Firesafetyandsecurityproducts 03.2010

Configuration

Thefollowingconfigurationsare possiblethroughcontrolleror configurationtool:

lAfter activating the output remains:

Steadyoutput

Pulseoutput: Howlong the contact remainsactivecan be configured bycontroller or

configuration tools(pulseduration).

lFailsafebehavior when the FD18-BUSdetector line iscurrent-free or indegraded mode.

The error behavior definesthe position of the output incaseof an error:

Off: Output remainsinthe same position asbefore the error

Activation:Output isactivated incaseof an error

Deactivation: Outputisdeactivated incaseof an error

Thecontroller doesnot monitor externalequipmentstatus(activated/inactivated).

Invertedoperation (outputlinesnotmonitored)

-Beused for controlling(e.g. closingadoor).

-Themoduleswitchestheexternallysupplied 24 VDC voltage inactivestatusonthe

output.

-Innormalstatusthere isnomonitoringfor openlineandshort circuit.

-Thejumper ontheinput/output modulemust be plugged ontoJ2/J4(Fig. 4).

Fig. 4Input/output modulejumper positionJ2, J4

Fig. 5Connectiondiagramfor inverted operation, e.g. whenused asdoor retainer.

Ininactivestatusthe24 VDC are permanentlyapplied totheoutput andmaykeep adoor

open, for example.Whentheoutputisswitched toactive,theoutput goesinto"open"status

(= no24 VDC voltage)andthedoor isclosed.

Comment:

Inthisexample, thedoor wouldalsocloseifthe 24 VDC supplywere tofail, e.g. duetoaline

problem(short circuit, openline).

Configuration

Under inverted mode, thefollowingconfigurationsare possiblethroughcontroller or

configurationtools:

lAfter activatingtheoutput remains:

Steadyoutput

Pulseoutput: Howlongthecontact remainsactivecanbeconfigured bycontroller or

configurationtools(pulseduration).

lFailsafebehavior whentheFD18-BUSdetector lineiscurrent-free or indegraded mode.

Theerror behaviordefinesthepositionoftheoutput throughcontroller or configuration

toolsincaseofanerror:

Off: Output remainsinthesamepositionasbefore theerror

Activation: Outputisactivated incaseofanerror

Deactivation: Output isdeactivated incaseofanerror

Thecontroller doesnot monitor externalequipmentstatus(activated/inactivated).

BuildingTechnologies A6V10214492_a_en_--

Firesafetyandsecurityproducts 03.2010

Drycontactoutput

Potential-free contact(Outputnotmonitored)

-Beused for controlling(e.g. closingadoor).

-Output controlisnot monitored.

-Anexternallysupplied 24 VDC voltage isnotneeded.

-Thejumper ontheinput/output modulemust be plugged ontoJ1/J3(Fig. 6).

Fig.6Input/output modulejumper positionJ1

Fig.7Connectiondiagramforpotential-free contact output

Configuration

Thefollowingconfigurationsare possiblebycontroller orconfigurationtools:

lThecontactisactive, when:

Normalmode: normallyopenNO closes

Inverted mode: normallyclosed NC opens

lAfter activatingtheoutput remains:

Steadyoutput

Pulseoutput: Howlongthecontact remainsactivecanbeconfigured bycontroller or

configurationtools(pulseduration).

lFailsafebehavior whentheFD18-BUSdetector lineiscurrent-free or indegraded mode.

Theerror behaviordefinesthepositionoftheoutput throughcontroller or configuration

toolsincaseofanerror:

Off: Output remainsinthesamepositionasbefore theerror

Activation: Outputisactivated incaseofanerror

Deactivation: Output isdeactivated incaseofanerror

Thecontroller doesnot monitor externalequipmentstatus(activated/inactivated).

Structure

Themoduleconsistsofthemodulecarrier, theprinted circuit board andthecover. Theprinted

circuit board includestheLEDs. TheLEDsindicatethestatesoftheinputs/outputs. Thecover

oftheprinted circuit board istransparent, sothat thestateoftheLEDsisvisibleevenwhen

thehousingisclosed.

Toprotect themodulesfromenvironmentalinfluences,housingFDCH221 isoptional.

BuildingTechnologies A6V10214492_a_en_--

Firesafetyandsecurityproducts 03.2010

Fig.8Overview

No.

Signification

1 LEDsfor thestatusindicationofthein-/output

2 Jumper for thepolarityofthemonitoringfor output 1

3 Connectionoutput 1

4 Port for theconnectionofthe24Vsupplyfor output 1

5 Port for theconnectionofthe24Vsupplyfor output 2

6 Connectionoutput 2

7 Jumper for thepolarityofthemonitoringfor output 2

8 Port for theconnectionoftheFD18-BUSdetectionline

9 Connectioninput 1

10 Connectioninput 2

Jumper

Jumperposition Signification

Output1isnot monitored.

Output1ismonitored.(factorydefault)

Output2isnot monitored.

Output2ismonitored.(factorydefault)

Iftheconfigurationsonthecontrolpanelandjumper don'tmatch, thisisrecognized andan

error message istriggered.

Anyother jumper positionisnot allowed.

LEDindicator

For eachin-/output, onered LEDindicatethestatus.

LED Signification

Off Normaloperation, in/outputis

monitored.

Flashesevery1s, 250mson Input/output activated

Input 1LEDflashesevery1s, 2...5mson Localizationmode

BuildingTechnologies A6V10214492_a_en_--

Firesafetyandsecurityproducts 03.2010

Installation

Fig. 9

Fig. 10

Fig. 11

Fig. 12 Detectionlineconnection

Preparation

1. Determinetype ofinstallation:

–Installationoutside aswitchingcabinet or acontrolunit:

useFDCH221 housing(Fig. 10).

–Installationdirectlyinaswitchingcabinet or acontrolunit:

mount themoduleonanevensurface(Fig. 9).

Damagebywater!

InhumidorwetenvironmentsalwaysuseFDCH221housing!

MountingFDCH221 housing

1. Openthehousing.

2. Determinethepositionofthecableentriesinthehousing

andbreakthemout.

3. Mount thehousingonanevensurfacewithtwoscrews

(Fig. 10). Distancebetweenholes:182.0 1.0mm.

4. Insert thecablesandfixthecablesinthehousing.

5. Insert thesealandfixthelidadditionallywithfourscrews

(Fig. 11) (onlythiswayisIP65 protectionguaranteed).

The housinglidistransparent.Considerasuitable

installationpositiontomakesurethattheLEDsofthe

modulearevisibleatanytime.

Procedurewithinstallationinthehousing

CAUTION

Overheatingofthein/outputmodule!

1. Openthehousing.

2. Placethemoduleinthehousingandfixit withtwo

screws(Fig. 9/10).

3. Closethehousing.

Procedurewithinstallationonanevensurface

1. Placethemoduleonanevensurface.

2. Fixthemodulewithtwoscrews(M4 X15) (Fig. 9).

Distancebetweenholes: 63.5 1.0mm

Electricconnection

1. ReferringtoFig. 1,3,5,7,12 connect thecablestothe

correspondingterminals.

2. Connect resistor/ diode .Theresistorsmust be

connected at theendofthemonitored line.

3. Fixthecablestothemodule

CAUTION

Mind thepositiveandnegativepolarwhenconnectingthe

diodes.

BeijignSiemensCeberusElectronics Ltd.

No.18 XinxiRoadShangdi Information IndustryBase,

Haidian District,Beijing100085 China

Tel.: +1062962255

Fax:+1062987387

www.sbt.siemens.com

©Dataanddesignsubjecttochangewithoutnotice.

DocNo. A6V10214492_a_en_-- Version a ManualFD18

Edition 03.2010

Dimension

In:mm

203

110

Specification

Operatingvoltage 12 …32 VDC

Operatingcurrent (quiescent) 0.56 mA

Activationcurrent 0.85 mA

Output

Capacity

Resistor

Diode

2A@24 VDC

3.3k Ω

1N5404

Input

-Resistor

3.3k Ω/ 680 Ω

Operatingtemperature 0 ... +42 °C

Storage temperature –20 ... +75 °C

Humidity ≤95 %rel.

Communicationprotocol FD18-BUS

Connectionterminals 1.0... 1.5mm2

Color

–Housing

–Cover

white, RAL9010

transparent

ProtectioncategoryEN60529 / IEC529/GB4208-93

–WithFDCH221 housing

IP65

Detailsforordering

Type Material No. PartNo. Designation Weight

FDCIO181-2 S54322-F2-A1 100856218 Input/output module 0.07Kg

FDCH221 S54312-F3-A1 100686595 AuxiliaryHousing(IP65) 0.250 Kg

Tabla de contenidos

Otros manuales de Sistema de E/S de Siemens

Siemens

Siemens SIMATIC ET 200eco PN Manual de usuario

Siemens

Siemens FDCI181-2 Manual de usuario

Siemens

Siemens APACS+ Manual

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC RQ 4x120VDC-230VAC/5A CO HA Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens Simatic ET 200S 2/4AI RTD ST Manual de usuario

Siemens

Siemens SIMATIC ET 200SP HA Documento técnico

Siemens

Siemens Simatic S7-1500 Manual de lista de piezas

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP HA DQ 32x24VDC/0.5A HA Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200iSP Manual de usuario

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMADYN D EA12 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Documento técnico

Siemens

Siemens SIMATIC PROFINET Manual de lista de piezas

Siemens

Siemens SIMATIC TI505 Manual de usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario