ICP DAS USA TM-AD2 Manual de usuario

tM-AD2 Quick Start

Quick Start

for tM-AD2

Dec 2015, Version 1.0.0

Congratulations on purchasing the tM-AD2 the most popular automation solution for

remote monitoring and control applications. This Quick Start Guide will provide

information needed to get started with the tM-AD2. Please also consult the User Manual

for detailed information on the setup and use of the tM-AD2.

In addition to this guide, the shipping box includes the following items:

tM-AD2

ICP DAS Website

http://www.icpdas.com/

tM-AD2 Quick Start

----------------------------------------------------------------------------------

Understanding the Hardware Specifications

and Wiring Diagrams

Before installing the hardware, you should have a basic understanding of hardware

specification and the wiring diagrams.

System Specifications：

tM-AD2 Quick Start

I/O Specifications：

Wire Connection：

Pin Assignment：

tM-AD2 Quick Start

Make sure the switch placed in the

“Init” position.

--------------------------------------------

--------------------------------------

Connecting to the PC and the Power Supply

The tM-Series series is equipped with an RS-485 port

for connection to a 232/USB converter to PC

--------------------------------------------

Booting the tM-Series in

Init Mode

Connect to the PC

using an RS-485 Converter

Connect to PC

using a USB Converter

7520

Power Supply

232

485

Series

Power Supply

USB

485

7561

Series

tM-AD2 Quick Start

--------------------------

-------------------------------------------------------

Installing the DCON Utility

The DCON Utility is an easy-to-use tool designed to enable simple configuration of I/O

modules that use the DCON protocol.

Step 1: Locate the DCON Utility

The DCON Utility can be obtained from the companion CD or from the

ICPDAS FTP site:

ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/

CD:\Napdos\Driver\DCON_Utility

-----

-----------------------------------------------------------------------------

Using the DCON Utility to Initialize the

tM-Series Module

The tM-Series is an I/O module based on the DCON protocol, meaning that you can use

the DCON Utility to easily initialize it.

Step 1: Run the DCON Utility_Pro

Double-click the DCON Utility Pro

Step 2: Use the COM1 port to communicate with the

tM-Series

Click the “COM Port” option from the menu and a dialog box will be displayed that will

allow you to set the communication parameters as described in the table below.

tM-AD2 Quick Start

Start Search

Stop Search

Step 3: Search for the

tM-Series

module

Click “Start Search” button from the toolbox to search for the tM-Series module.

After the tM-Series module is displayed in the list, click “Stop Search” button.

Communication

parameter Factory

default Value

Address 00

Baud Rate 9600

Protocol DCON

Checksum Disabled

Parity N,8,1

tM-AD2 Quick Start

Step 4: Connect to the tM-Series

After clicking on the name of the module in the list, a dialog box will be displayed.

Step 5: Initialize the tM-Series module

Set the “Address” field in the dialog box to 1 and then click “Setting Module

Configurations ” button to save the settings.

Make sure the INIT switch is placed in the

“Normal” position.

----------------------------------------------------------------------------------

Starting the Module Operation

After rebooting the tM-Series module, search for the module to make sure the settings

have been changed. You can double click on the name of the module in the list to open

-----------------------------------

---------

Rebooting the tM-Series

Module in Normal Mode

tM-AD2 Quick Start

the configuration dialog box.

Address

Description

Attribute

30001 ~ 30002

40001 ~ 40002

Analog input value of channel 0 to 1

40257 ~ 40258

Analog input type code of channel 0 to 1

R/W

40481

Firmware version (low word)

40482

Firmware version (high word)

40483

Module name (low word) , 0x2001

40484

Module name (high word) , 0x0700

40485

Module address, valid range: 1 ~ 247

R/W

40486

Bits 5:0

Baud rate, 0x03 ~ 0x0A

Code

0x03

0x04

0x05

0x06

Baud

1200

2400

4800

9600

Code

0x07

0x08

0x09

0x0A

Baud

19200

38400

57600

115200

Bits 7:6

00: no parity, 1 stop bit

01: no parity, 2 stop bits

10: even parity, 1 stop bit

11: odd parity, 1 stop bit

R/W

40488

Modbus response delay time in ms, valid range: 0 ~ 30

R/W

40489

Host watchdog timeout value, 0 ~ 255, in 0.1s

R/W

40490

Channel enable/disable, 00h ~ 03h

R/W

40492

Host watchdog timeout count, write 0 to clear

R/W

40494

4mA under range threshold in 0.1mA, 0 ~ 40

R/W

Address

Description

Attribute

10129 ~ 10130

00129 ~ 00130

Over/under range status of channel 0 to 1 for 4 ~ 20mA or 0 ~ 20mAranges

00257

Protocol, 0: DCON, 1: Modbus RTU

R/W

00258

Protocol, 0: determined by 00257, 1: Modbus ASCII

R/W

00261

1: enable, 0: disable host watchdog

R/W

00269

Modbus data format, 0: hex, 1: engineering

R/W

00270

Host watch dog timeout status, write 1 to clear host watch dog timeout status

R/W

00271

1: enable, 0: disable fast mode

R/W

00273

Reset status, 1: first read after powered on, 0: not the first read after powered on

-----------------------------------------------------------

----------------------

Modbus Address Mapping

Tabla de contenidos

Otros manuales de Sistema de E/S de ICP DAS USA

ICP DAS USA

ICP DAS USA I-7021 Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2053 Manual de usuario

ICP DAS USA

ICP DAS USA I-7088 Manual de usuario

ICP DAS USA

ICP DAS USA 7188X Manual de usuario

ICP DAS USA

ICP DAS USA I-7000 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7046 Manual de usuario

ICP DAS USA

ICP DAS USA I-7043D Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD8 Manual de usuario

ICP DAS USA

ICP DAS USA DGW-521 Manual de usuario

ICP DAS USA

ICP DAS USA PET-7000 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7050 Manual de usuario

ICP DAS USA

ICP DAS USA I-9K Series Manual de usuario

ICP DAS USA

ICP DAS USA PIO-D64U Manual de usuario

ICP DAS USA

ICP DAS USA PET-7050 Manual de usuario

ICP DAS USA

ICP DAS USA ET-2217CI Manual de usuario

ICP DAS USA

ICP DAS USA tM-R5 Manual de usuario

ICP DAS USA

ICP DAS USA A-826 Series Manual de usuario

ICP DAS USA

ICP DAS USA DB-16R Manual de usuario

ICP DAS USA

ICP DAS USA WF-2055 Manual de usuario

ICP DAS USA

ICP DAS USA DN-8K32R Manual de usuario

ICP DAS USA

ICP DAS USA PISO-813 Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2054D Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2054C Manual de usuario

ICP DAS USA

ICP DAS USA I-7018 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario

ICP DAS USA tM-AD2 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas