Siemens SIMATIC ET 200S Manual de usuario

Digital electronic module 8DO

DC24V/0.5 A (6ES7132-4BF00-0AA0)

___________________

SIMATIC

ET 200S distributed I/O

Digital electronic module 8DO DC24V/0.5 A

(6ES7132-4BF00-0AA0)

Manual

10/2015

A5E01077385

-AB

Preface

Properties

Diagnostics

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E01077385-AB

Ⓟ

10/2015 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Manual, 10/2015, A5E01077385-AB 3

Preface

Purpose of the manual

This manual supplements the

ET 200S Distributed I/O System

Operating Instructions.

General functions for the ET 200S are described in the ET 200S Distributed I/O System

Operating Instructions (http://support.automation.siemens.com/WW/view/en/1144348).

The information in this document along with the operating instructions enables you to

commission the ET 200S.

Basic knowledge requirements

To understand these operating instructions you should have general knowledge of

automation engineering.

Scope of the manual

This manual applies to this ET 200S module. It describes the components that are valid at

the time of publication.

Recycling and disposal

Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For

environmentally compliant recycling and disposal of your electronic waste, please contact a

company certified for the disposal of electronic waste.

Additional support

If you have any questions relating to the products described in this manual and do not find

the answers in this document, please contact your local Siemens representative

(http://www.siemens.com/automation/partners).

A guide to the technical documentation for the various SIMATIC products and systems is

available on the Internet. (http://www.siemens.com/simatic-docu).

The online catalog and ordering systems are available on the Internet

(http://www.siemens.com/automation/mall).

Preface

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

4Manual, 10/2015, A5E01077385-AB

Training center

We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation

system. Please contact your regional training center or the central training center in

D -90327, Nuremberg, Germany (http://www.siemens.com/sitrain).

Technical Support

You can contact Technical Support for all Industry Automation products by means of the

Internet Web form for the Support Request

(http://www.siemens.com/automation/csi_en_WW/support_request).

Additional information about Siemens Technical Support is available on the Internet

(http://www.siemens.com/automation/csi_en_WW/service).

Service & Support on the Internet

In addition to our documentation, we offer a comprehensive knowledge base on the Internet

(http://www.siemens.com/automation/csi_en_WW/support).

There you will find:

●Our Newsletter, which constantly provides you with the latest information about your

products.

●The right documentation for you using our Service & Support search engine.

●The bulletin board, a worldwide knowledge exchange for users and experts.

●Your local contact for Automation & Drives in our contact database.

●Information about on-site services, repairs, spare parts, and lots more.

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Manual, 10/2015, A5E01077385-AB 5

Table of contents

Preface ................................................................................................................................................... 3

1 Properties ............................................................................................................................................... 6

1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)....................................6

2 Diagnostics ........................................................................................................................................... 12

2.1 Diagnostics using LED display ...............................................................................................12

Index..................................................................................................................................................... 13

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

6Manual, 10/2015, A5E01077385-AB

Properties

1.1

Digital electronic module 8DO DC24V/0.5 A

(6ES7132-4BF00-0AA0)

Properties

●Digital electronic module with eight outputs

●Output current 0.5 A per output, total current 4 A

●Rated load voltage 24 V DC

●Short-circuit protection

●Suitable for solenoid valves, DC contactors, and indicator lights

●Supports isochronous operation

Special features

When the rated load voltage 24 V DC is applied to the power module via a mechanical

contact, the digital outputs carry a "1" signal for about 50 μs for switching reasons. You have

to take this into consideration if you use this module in connection with high-speed counters.

Requirements for operation

It is possible to operate the 8DO DC24V 0.5A digital electronic module using the following

interface modules with the order numbers specified (or higher). The interface modules listed

in the table are not subject to any constraints.

Interface module

Order number (or higher)

Firmware version (or

higher)

IM 151-1 STANDARD 6ES7151-1AA03-0AB0 ---

IM 151-1 FO STANDARD

6ES7151-1AB02-0AB0

---

IM 151-1 HIGH FEATURE

6ES7151-1BA01-0AB0

V2.1.3

IM 151-3 PN

IM 151-3 PN HIGH FEATURE

IM 151-3 PN FO

6ES7151-3AA20-0AB0

6ES7151-3BA20-0AB0

6ES7151-3BB21-0AB0

V4.0.1

Properties

1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Manual, 10/2015, A5E01077385-AB 7

General terminal assignment

Note

Terminals A4, A8, A3 and A7 are only available at specified terminal modules.

Terminal assignment for 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)

Terminal

Allocation

Terminal

Allocation

Notes

•DOn: Output signal, channel n

•AUX1: Mass M (from power module) or voltage bus (freely usable

up to 230 V AC)

DO2

DO3

DO6

DO7

AUX1

Usable terminal modules

Usable terminal modules for 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)

TM-E15C26-A1

(6ES7193-4CA50-0AA0)

TM-E15C24-01

(6ES7193-4CB30-0AA0)

Spring terminal

TM-E15S26-A1

(6ES7193-4CA40-0AA0)

TM-E15S24-01

(6ES7193-4CB20-0AA0)

Screw-type terminal

TM-E15N26-A1

(6ES7193-4CA80-0AA0)

TM-E15N24-01

(6ES7193-4CB70-0AA0)

Fast Connect

Properties

1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

8Manual, 10/2015, A5E01077385-AB

2-wire connection

The following configuration example shows a two-wire connection with the electronic

modules 8DO DC24V. You require further terminals so that sufficient terminals are available

for the mass M connection when the TM-E15S26-A1 terminal modules are used. In the

example this is implemented by the add-on terminal TE-U120S4x10, which you can mount

as of a width of 120 mm (8 EMs). You can naturally also use other terminals for this

configuration (for example, ET 200S potential distribution module 4POTDIS).

①

Terminal module TM-P15S23-A0

②

Power module PM-E 24 VDC

③

Electronic modules 8DI DC24V

④

Terminal modules TM-E15S26-A1

⑤

Actuator in 2-wire connection

⑥

Add-on terminal TE-U120S4x10

Properties

1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Manual, 10/2015, A5E01077385-AB 9

Block diagram

Figure 1-1 Block diagram of the 8DO DC24V 0.5A

Properties

1.1 Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0)

10 Manual, 10/2015, A5E01077385-AB

Technical specifications 8DO DC24V/0.5A (6ES7132-4BF00-0AA0)

Dimensions and weight

Width (mm)

Weight

Approx. 40 g

Module-specific data

Supports isochronous operation

Yes

Number of outputs

Cable length

•Unshielded Max. 600 m

•Shielded Max. 1000 m

Parameter length

3 bytes

Address space

1 byte

Voltages, currents, potentials

Rated Rated load voltage L+ (from power mod-

ule)

24 V DC

•Polarity reversal protection Yes 1

Total current of the outputs (per module)

4 A

Electrical isolation

•Between the channels No

•Between the channels and backplane bus Yes

Permissible potential difference

•Between different circuits 75 V DC / 60 V AC

Isolation tested

500 V DC

Current consumption

•From the rated load voltage L+ (no load) Max. 5 mA per channel

Power loss of the module

Typically 1.5 W

Status, interrupts, diagnostics

Status display

Green LED per channel

Diagnostics functions

Otros manuales para SIMATIC ET 200S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de Siemens

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens FDCIO181-2 Manual de usuario

Siemens

Siemens SICAM AI Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Documento técnico

Siemens

Siemens SIMATIC 505 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Documento técnico

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens Binary Input N 260 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIM-16 Manual de usuario

Siemens

Siemens SIMATIC ET 200eco PN Guía del usuario

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP HA Guía del usuario

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens Simatic ET200pro Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens FDCI221 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario