Robe SPOT 250 XT Manual de usuario

Table of contents

1. Safety instructions......................................................................................................... 3

2.Operating determinations .............................................................................................. 4

3. Description of the device .............................................................................................. 5

4.Installation ...................................................................................................................... 6

4.1Fitting the lamp........................................................................................................... 6

4.2 Lamp adjustment....................................................................................................... 7

4.3 Installation of an optional lens................................................................................... 7

4.4 Inserting/Exchanging gobos......................................................................................8

4.5 Rigging the fixture ..................................................................................................... 9

4.6 Changing the power supply settings ....................................................................... 11

4.7 Connection to the mains.......................................................................................... 12

4.8 DMX-512 connection/connection between fixtures ................................................. 12

5. DMX PROTOCOL.......................................................................................................... 13

6. Controller mode ........................................................................................................... 15

6.1 DMX addressing ..................................................................................................... 15

6.2 Remotely controllable functions .............................................................................. 15

7. Stand - alone mode...................................................................................................... 16

8. Functions of the control panel.................................................................................... 17

8.1 Addressing .............................................................................................................. 17

8.2 Slave control ........................................................................................................... 18

8.3 Fixture informations................................................................................................. 18

8.4 Personality options.................................................................................................. 20

8.5 Switching On/Off the lamp....................................................................................... 24

8.6Test sequences........................................................................................................ 25

8.7 Stand-alone setting ................................................................................................. 25

8.8 Reset function ......................................................................................................... 27

8.9 Special functions..................................................................................................... 27

9. Error and information messages................................................................................ 29

10.Technical specifications ............................................................................................ 31

11. Maintenance and cleaning ........................................................................................ 34

12. Appendix .................................................................................................................... 34

SPOT 250 XT

CAUTION!

Keepthis deviceaway fromrain andmoisture!

Unplugmains leadbefore openingthe housing!

FORYOUROWNSAFETY,PLEASEREADTHISUSERMANUALCAREFULLY

BEFOREYOUINITIALSTART-UP!

1. Safety instructions

Every person involved with installation and maintenance of this device have to:

-be qualilfied

- follow the instructions of this manual

CAUTION!

Be carefulwith youroperations.

Witha high voltage you can suffer

adangerous electricshock whentouchingthewires!

Thisdevice has leftour premises in absolutely perfect condition. Inorder to maintainthis condition and toensure

asafe operation, itis absolutely necessary for the user tofollow the safetyinstructions and warning noteswritten

in this manual.

Important:

Themanufacturer willnot acceptliability for anyresulting damagescaused by thenon-observance ofthis manual

or any unauthorized modification to the device.

Please consider that damages caused by manual modifications to the device are not subject to warranty.

Neverlet thepower-cord comeinto contact withother cables!Handle thepower-cord and allconnections withthe

mains with particular caution!

Make sure that the available voltage is not higher than stated on the rear panel.

Always plug in the power plug least. Make sure that the power-switch is set to OFF-position before you connect

the device to the mains.The power-plug has to be accessable after installing the device.

Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-

cord from time to time.

Alwaysdisconnect fromthe mains,when thedevice isnot inuse orbefore cleaningit. Onlyhandle thepower-cord

by the plug. Never pull out the plug by tugging the power-cord.

This device falls under protection class I.Therefore it is essential to connect the yellow/green conductor to earth.

The electric connection, repairs and servicing must be carried out by a qualified employee.

Do not connect this device to a dimmer pack.

Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.

During the initial start-up some smoke or smell may arise.This is a normal process and does not necessarily

mean that the device is defective.

Donot touch the device’s housing barehands duringits operation (housingbecomes hot)!

For replacement use lamps and fuses of same type and rating only.

CAUTION! EYEDAMAGES!

Avoidlooking directlyinto thelight source

(meantespecially forepileptics) !

2.Operating determinations

This device is a moving-head spot for creating decorative effects and was designed for indoor use only.

If the device has been exposed to drastic temperature fluctuation (e.g.after transportation), do not switch it on

immediately.Thearising condensationwater might damage yourdevice.Leavethe deviceswitched offuntilithas

reachedroomtemperature.

Never run the device without lamp!

Do not shake the device.Avoid brute force when installing or operating the device.

Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the

fixture at the transport handles.

Whenchoosing the installation-spot, pleasemake sure that the deviceis not exposed to extreme heat, moisture

or dust.There should not be any cables lying around.You endanger your own and the safety of others!

The minimum distance between light-output and the illuminated surface must be more than 1 meter.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.

Always fix the fixture with an appropriate safety-rope.Fix the safety-rope at the correct holes only.

Onlyoperate the fixtureafter having checked that the housing isfirmly closed andall screws are tightlyfastened.

The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may

explose and emit a high ultraviolet radiation, which may cause burns.

Themaximum ambient temperature

= 45° C mustnever be exceeded. Otherwise,the lamp is switchedoff and

the fixture is out of operation for 5 minutes.

CAUTION!

Thelens hasto bereplacedwhen itis obviouslydamaged,

sothat itsfunction is impaired,e. g.due to cracksor deepscratches!

Operate the device only after having familiarized with its functions. Do not permit operation by persons not

qualifiedfor operating the device.Most damages are theresult of unprofessional operation!

CAUTION!

Thelamp hasto be replacedwhen itis damaged

ordeformed due to theheat!

Please use the original packaging if the device is to be transported.

Please consider that unauthorized modifications on the device are forbidden due to safety reasons!

If this device will be operated in any way different to the one described in this manual, the product may suffer

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-

circuit, burns, electric shock, burns due to ultraviolet radiation, lamp explosion, crash etc.

1-Moving Head

2 -Yoke

3 - Base

4-Carrying handles

Rearpanel:

5-Power-switch

6- DMX output

7- DMX input

8 - Powercord

9 - Fuseholder

Front panel:

10 -Mode-button

11 -Enter-button

12 -Up-button

13-Down-button

14 - Display

3. Description of the device

4. Installation

4.1Fitting the lamp

DANGER!

Installthe lampswith the deviceswitchedoff only.

Unplugfrom mainsbefore !

To insert the lamp MSD 250 or MSD 250/2 open the top cover of the head (see the drawings to identify which

cover is top) by loosening the 4 Phillips screws on the front and rear sides of the top cover.Then open the

small lamp cover by loosening 3 fastening screws (see the drawing).If changing the lamp, remove the old lamp

from the socket.Insert the lamp to the socket.Do not install a lamp with a higher wattage! A lamp like this

generates temperatures the device is not designed for.Damages caused by non-observance are not subject to

warranty.Pleasefollow the lamp manufacturer‘s notes!Do not touch the glass-bulb bare hand during the

installation! Make sure that the lamp is installed tightly into the lampholder system.

Adjusttheoptimaldistance1-1.5 mmfromthelensby turning

thescrew"A"(seethedrawings"Lampadjustment"below).

Then close the small lamp cover by tighten 3 fastening

screwsagain.

Reclose the top cover of the head and tighten the 4 Phillips

screws

Beforestrikingthelamp, resetthe"LAti"and"LASt" counter

s in the menu of the Control Board, by pressing the "Up"

and "Down" buttons in one time and then confirming with

theEnter-button.

Donot operatethis fixturewith openedhousing-cover!

2 Phillips screws 2 Phillips screws

Top cover

Bottom cover Bottomcover

Lamp

Lamp cover 3fastening

screws

4.2 Lamp adjustment

Correct Incorrect

The SPOT 250 XT lampholder is aligned at the factory.Due to differences between lamps, fine adjustment may

improvelight performance.

Strike the lamp and focus the light on a flat surface (wall). As the optimum distance of lamp from lens was

adjusted during the installing or changing the lamp (by turning the screw "A"), it is necessary to adjust only the

second position by turning the screw "B", in order to center the hot-spot (the brightest part of the beam).

If the hot- spot seems to be too bright, you can lower its intensity by moving the lamp closer to the reflector. Do

so by turning srew "A" until the light is evenly distributed.

Ifthe light onthe edge seemsto be brighter as inthe center, the lamp istoo close atthe reflector.In thiscase, you

need to move the lamp away from the reflector until the light is evenly distributed and the beam appears bright

enough.

4.3 Installation of an optional lens

The device is delivered with a 15°-standard lens. If you wish to insert an optional 12° or 18°-lens (it is not the

standard part of delivery), please follow the instructions below:

Optional 12°-lens:

Remove the fixation-ring of the 15°-lens with an appropriate tool. Remove the lens. Install the optional 12°-lens

and fix it with the fixation-ring.

Keep optimum distance to lens

Optimum distance 1 - 1,5mm

Screw "A"

Screw "B"

15°- lens optional 12°- lens

Optional 18°-lens:

Unscrew the knurled-head screw on the plate of the light-output. Install the optional 18°-lens and fix it with the

knurled-headscrew.

4.4 Inserting/Exchanging gobos

DANGER!

Installthe goboswith the deviceswitchedoff only.

Unplugfrommainsbefore!

To insert the gobos open the top cover of the head by loosening the 4 Phillips screws on the front and rear sides

of the top cover.

Ifyou wishto use otherforms and patternsas the standard-gobos,or ifgobos are tobe exchanged, pleasefollow

theinstructions below:

Rotating gobo-wheel:

CAUTION!

Neverunscrew thescrews ofthe rotatinggobo

asthe ballbearing willotherwise beopened!

Remove the fixation-ring with an appropriate tool.Remove the gobo and insert the new gobo.Press the fixation-

ring together and insert it in the front of the gobo.

4.5 Rigging the fixture

Dangerof fire !

Wheninstalling thedevice, makesure thereis nohighly inflammable

material(decoration articles,etc.) inbetween a distanceof min. 0,5m.

Warning ! Use 2 clampsto rig thefixture on the truss.

Followthe instructionsmentionedat thebottom ofthebase.

Makesure that thedevice isfixedproperly! Ensurethat

thestructure (truss) towhich you areattaching the fixturesis secure.

The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1

hourwithout anyharming deformation.

The installation must always be secured with a secondary safety attachment, e.g.an appropriate catch net.This

secondary safety attachment must be constructed in a way that no part of the installation can fall down if the

main attachment fails.

Whenrigging, derigging orservicing the fixture stayingin the areabelow the installation place,on bridges, under

highworking placesand other endangeredareas isforbidden.

Themoving-head can be placed directlyon the stage floor orrigged in any orientation on a truss without altering

itsoperation characteristics (see thedrawing).

You canfix the Spot250 XT ona truss via 2Omega holders orusing the mountingplate(it is notthe standard part

of delivery) or screw the clamps directly to the 2 holes (5) in the base.

For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture.You must

only use safety-ropes with screw-on carabines.Pull the safety-rope through the two apertures on the bottom of

the base and over the trussing system etc.Insert the end in the carabine and tighten the fixation screw.

Fixation via Omega holders

1.Bolt each clamp (1) to the omega holder (4) with M12 bolt and lock nut through the hole in the holder.

2.Fasten the omegaholders on the bottomof the base byinsertingboth quick-lockfasteners(3) into theholes of

the base and tighten fully clockwise.

3.Fasten the safety-rope (2) through the two apertures on the bottom of the base and over the trussing system.

1-Clamp

2-Safety-rope

3-Quick-lockfastener

4-Omegaholder

5-Mountingholes 2x M10

Fixation via a mounting plate

1. Screw 2 clamps (1) to the mounting plate (4) with M12 bolts and lock nuts through the holes in the

mounting plate (4).

2.Insert the 4 quick-lock fasteners (3) into the holes on the bottom of the base and tighten fully clockwise.

3.Fasten the safety-rope (2) through the two apertures on the bottom of the base and over the trussing system.

1-Clamp

2-Safety-rope

3-Quick-lockfasteners

4-Mountingplate

Tabla de contenidos

Otros manuales de Equipo de iluminación de Robe

Robe

Robe Tarrnatula Manual de usuario

Robe

Robe ColorSpot 250 AT Manual de usuario

Robe

Robe Anolis Divine 160 RGBW/RGBA/PW/TW Manual de usuario

Robe

Robe Stage Faze 1500AT Manual de usuario

Robe

Robe Robin T2 Manual de usuario

Robe

Robe Anolis Calumma XS MC Manual de usuario

Robe

Robe Anolis ArcSource Outdoor 48 MC Integral RGBW Manual de usuario

Robe

Robe Anolis Calumma XS MC Manual de usuario

Robe

Robe ROBIN LEDBeam 350 RGBA Manual de usuario

Robe

Robe DT Series Manual de usuario

Robe

Robe Anolis ArcDot-US Manual de usuario

Robe

Robe ROBIN Pointe Manual de usuario

Robe

Robe DigitalSpot 7100 DT Manual de usuario

Robe

Robe Robin MMX Blade Manual de usuario

Robe

Robe COLORSPOT 170 AT Manual de usuario

Robe

Robe Led Blinder 196 LT Manual de usuario

Robe

Robe ClubWash 250CT Manual de usuario

Robe

Robe Robin DLX SPOT Manual de usuario

Robe

Robe ColorWash 575E AT Manual de usuario

Robe

Robe Robin BMFL FollowSpot Manual de usuario

Robe

Robe Color Wasf 1200E Manual de usuario

Robe

Robe LightDome 575 Manual de usuario

Robe

Robe Flare CB Series Manual de usuario

Robe

Robe ANOLIS Eminere Side 1 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario