Quantum StorNext QD6000 Manual de usuario
Replacing a Controller Battery
StorNext QD6000/QD7000 Base System
6-68477-01 Rev A *6-68477-01 Rev A
ii Replacing a Controller Battery
StorNext QD6000/QD7000 Base System, Replacing a Controller Battery, 6-68477-01 Rev A, July 2016, Product
of USA.
©2016 All rights reserved. Quantum, the Quantum logo, DXi, Scalar and StorNext are registered trademarks of
Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the
property of their respective owners.
About this guide iii
About this guide
NOTE: The Lancaster firmware is used on the E5600, Titan RAID controller, only. Refer to the NetApp
to Quantum Naming Decoder section for additional information.
This section provides the following information:
•Intended audience
•Prerequisites
•NetApp to Quantum Naming Decoder
Intended audience
This guide is intended for storage customers and technicians.
Prerequisites
Prerequisites for installing and using this product include knowledge of:
•Servers and computer networks
•Network administration
•Storage system installation and configuration
•Storage area network (SAN) management and direct attach storage (DAS)
•Fibre Channel (FC) and Ethernet protocols
iv Replacing a Controller Battery
NetApp to Quantum Naming Decoder
Use Ta b l e 1 to correlate the NetApp product nomenclature to the equivalent Quantum-storage
naming conventions.
Ta b l e 1 Product Nomenclature
E-Series NetApp Product Quantum-Storage Description
Controller-Drive Tray Base System Quantum uses Base System when referring to a
drive tray with the RAID controllers.
Drive Tray Expansion Unit Quantum uses Expansion Unit when referring
to a drive tray with the environmental services
modules (ESMs).
E5600 (Code Name: Titan) RAID controller Four 16Gb/s FC SFP+ host ports
E5500 (Code Name: Soyuz) RAID controller Four 16Gb/s FC SFP+ host ports
E5400 (Code Name: Pikes Peak) RAID controller Four 8Gb/s FC SFP+ host ports
DE6600 (Code Name: Wembley) 4U 60-drive enclosure 60 3.5 inch disk drives
E5560 or E5660
(DE6600 4U drive enclosure with
E5500 or E5600 RAID controllers)
Quantum StorNext
QD7000
E5460
(DE6600 4U drive enclosure with
E5400 RAID controllers)
Quantum StorNext
QD6000
E5424
(DE5600 24-drive 2U drive
enclosure (Code Name: Camden)
with E5400 RAID controllers)
Quantum StorNext
QS2400
E5412
(DE1600 12-drive 2U drive
enclosure (Code Name: Ebbets)
with E5400 RAID controllers)
Quantum StorNext
QS1200
Copyright 2014 NetApp Inc. All rights reserved.
Replacing a Failed Controller Battery in the E5660 Controller-
Drive Tray
To access this product, go to the NetApp® Support Site at mysupport.netapp.com.
You can determine whether you have a failed controller battery in two ways:
The Recovery Guru directs you to replace a failed controller battery.
The amber Battery Service Action Required LED indicates a failed controller battery.
Before you replace the controller battery, gather antistatic protection, a replacement controller battery, and a
controller air blocker.
ATTENTION Possible hardware damage – If you perform this procedure with the power turned on, the equipment
might overheat if the controller slot is left open for more than three minutes. To prevent the possibility of overheating,
you must insert the controller air blocker into the empty controller slot when you service the controller.
Figure 1. E5660 Controller-Drive Tray
1. Power Canister A
2. Controller Canister A
3. Controller Canister B
4. Power Canister B
2 - Replacing a Battery in the E5660
Removing a Controller Canister
ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper
antistatic protection when handling tray components.
1. Gather support data about your storage array by using one of these methods:
Use the storage management software to collect and save a support bundle of your storage array. From the
Array Management Window, select Monitor > Health > Collect Support Data Manually. Then name and
specify a location on your system where you want to store the support bundle.
Use the command line interface (CLI) to run the save storageArray supportData command to gather
comprehensive support data about the storage array. For more information about this command, refer to the
Command Line Interface and Script Commands Programming Guide.
NOTE Gathering support data can temporarily impact performance on your storage array.
2. Did the Recovery Guru direct you to replace a failed controller battery?
Yes – Go to step 3.
No – Run the Recovery Guru to identify the failed component.
3. Locate the failed controller battery by checking the Battery Service Action Required LED.
If a fault is detected, the amber Battery Service Action Required LED is on.
NOTE The figures in this document show a SAS configuration with four connectors. Your controller canister
might have a different number and type of host interface connectors.
Figure 2. SAS E5600 Controller Service Action LEDs
1. Controller Service Action Allowed LEDs (Blue)
2. Controller Service Action Required LEDs (Amber)
3. Seven-Segment Display
4. Battery Service Action Required LED (Amber)
4. Record the information from the seven-segment display on the controller-drive tray.
The display flashes a sequence of codes. To find information about the displayed diagnostic codes, refer to the
E5600 Controller-Drive Tray and Related Drive Trays Installation Guide.
5. Use either the GUI (first bullet) or the CLI (second bullet) to take the appropriate controller offline.
In the Hardware pane in the Array Management Window, right-click the picture of the controller you want to
take offline, and select Advanced > Place > Offline.
Run the following command:
smCLI <DNS-network-name-or-IP-address> -c "set controller [(a | b)]
Replacing a Battery in the E5660 - 3
availability=offline";
6. Wait for the blue Controller Service Action Allowed LED to come on. For a large configuration, this indication
might take several minutes.
7. Put on antistatic protection.
8. Label each cable that is attached to the controller canister with the failed battery so that you can reconnect each
cable correctly after the controller canister is reinstalled.
ATTENTION Potential degraded performance – To prevent degraded performance, do not twist, fold, pinch,
or step on the cables. Many cables have a minimum bending radius. Check the specifications for your cables,
and do not bend any cable tighter than the minimum specified radius.
9. Disconnect all interface cables (drive connections, host connections, and Ethernet connections) from the
controller canister that has the failed battery.
If the storage array is running while you perform the controller battery replacement, do not disturb the second
controller canister.
10.Prepare the controller air blocker by removing it from the packaging and folding it inward at right angles so it is
ready to insert into the open controller slot.
Figure 3. Controller Air Blocker
11.Remove the controller canister that has the failed controller battery.
NOTE The following figure shows the controller in the bottom position within the controller-drive tray. However,
you might be removing the controller and inserting the controller air blocker in the top position. The required
actions are similar.
4 - Replacing a Battery in the E5660
a. Unlock the controller canister release lever, and pull the release lever outward to release the controller
canister.
b. Using the release lever, pull the controller canister out of the controller-drive tray.
Figure 4. Removing and Replacing a Controller Canister
12.Invert the controller canister, and set it on a flat, static-free surface, with the release levers up.
ATTENTION Possible equipment damage – The controller slot cannot remain open for more than three
minutes because of the possibility of overheating the equipment. The controller air blocker fills the controller slot
so that the equipment does not overheat.
Replacing a Battery in the E5660 - 5
13.Insert the controller air blocker into the open controller slot to make sure that correct airflow is maintained.
Figure 5. Inserting the Controller Air Blocker into the Open Controller Slot
Replacing a Controller Battery
1. Unpack the new controller battery.
a. Set the new controller battery on a flat, static-free surface near the controller-drive tray.
b. Save all of the packing materials in case you need to return the controller battery.
2. Remove the top cover from the controller canister.
6 - Replacing a Battery in the E5660
Press down on both of the top cover latch buttons as you slide the top cover off the controller canister.
Figure 6. Battery and Locking Tab in the Controller
1. Top Cover Latch Buttons
2. Battery Circuit Board
3. Battery Locking Tab
3. Remove the failed battery.
a. Move the battery locking tab down to pull the failed controller battery out of the controller canister.
b. Remove the failed controller battery by sliding it towards the rear of the controller canister.
4. Install the new battery.
a. Insert the new battery at a slight downward angle into the controller canister.
b. Slide the battery towards the front of the controller canister making sure that the battery slides under the side
guide pins as you continue to slide the battery to correctly seat it against the back surface.
If the battery is not correctly seated, you will not be able to reinstall the top cover on the controller canister as
directed later. If you suspect that the new battery is not correctly seated, you might need to slide the new battery
out and insert it again.
5. Move the locking tab up to secure the new battery circuit board to the controller canister.
6. Reinstall the top cover on the controller canister by sliding it forward until the top cover latch buttons click.
Reinstalling the Controller Canister
1. Remove the controller air blocker.
Otros manuales para StorNext QD6000
5
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Almacenamiento de Quantum
Quantum
Quantum LTO-4 (Model B) Manual de usuario
Quantum
Quantum Scalar i2000 Manual de usuario
Quantum
Quantum Quantum Atlas 10K II 9.2/18.4/36.7/73.4 GB Manual de usuario
Quantum
Quantum Fireball Plus AS Manual de usuario
Quantum
Quantum DPM 5500 Manual de usuario
Quantum
Quantum StorNext QD6000 Manual de usuario
Quantum
Quantum Scalar 10K Manual de instrucciones
Quantum
Quantum P7000 Series Manual de usuario
Quantum
Quantum StorNext QD7000 Manual de usuario
Quantum
Quantum Scalar 50 Guía
Quantum
Quantum ATL M-Series Manual de usuario
Quantum
Quantum Q2000 Manual de usuario
Quantum
Quantum StorNext QM1200 Manual de usuario
Quantum
Quantum PX502 Manual de referencia
Quantum
Quantum Tape Drives A-Series Manual de usuario
Quantum
Quantum A-Series FTP Manual de usuario
Quantum
Quantum Scalar i6000 Manual de usuario
Quantum
Quantum ValueLoader DLT VS160 Manual de usuario
Quantum
Quantum ValueLoader DLT VS160 Manual de usuario
Quantum
Quantum Scalar i80 Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario