Quantum DAT 320 CD320UE Manual de usuario

www.quantum.com

DAT 320

DAT 320 Tape Drive Quick

Start Guide

Quantum DAT 320, models CD320UH (Internal) and CD320UE (Tabletop),

are the most reliable DAT drives on the market, delivering reliability features

to extend media life.

Figure 1 Internal Drive

Contents

Before Installing the DAT 320 Tape Drive

in Your System........................................2

Avoiding Electrostatic Damage..........2

Preinstallation Requirements .............2

Unpacking and Inspecting the Drive..2

Required Tools ....................................3

Installing the Internal DAT 320 Tape Drive

in Your Server .........................................3

Preparing Mounting Bay ....................3

Attaching Mounting Hardware ..........3

Installing the Tape Drive.....................5

Attaching the USB Cable ....................6

Connecting the USB Cable from the

Tape Drive to the Server .....................6

Attaching the Power and USB Cables to

the Tape Drive.....................................7

Securing the Drive..............................8

Completing Your Installation .............9

Installing the Tabletop DAT 320 Tape Drive

to Your System .....................................10

Connecting the Power and USB Cables

to Your Tabletop Drive......................10

Completing Your Installation ...........10

Safety Compliances ..............................11

Electromagnetic Compatibility (EMC)

Compliances .........................................12

2Before Installing the DAT 320 Tape Drive in Your System

DAT 320 Quick Start Guide

Before Installing the DAT 320 Tape Drive in Your System

Avoiding Electrostatic

Damage

Your internal tape drive has very sensitive components that are prone to damage from

electrostatic discharge (ESD). Use extreme care when handling the drive, as it can be

damaged by ESD.

Before handling the drive, read the ESD instructions that follow to prevent damage to

the drive.

• Wear an ESD-preventive grounding wrist strap or observe similar ESD precautions

when working with the drive. Be sure the wrist strap makes good skin contact. Do

not remove the wrist strap until you finish working with the drive.

• Before you remove the drive from the antistatic bag, touch a metal or grounded

surface to discharge any static electricity buildup from your body.

• Avoid contact between the drive, other equipment, and clothing. The wrist strap

only protects the equipment from ESD voltages on the body; ESD voltages on

clothing can still cause damage.

• When the drive is not being used, keep it in its antistatic bag.

• Hold the drive by its edges only. Avoid touching any exposed parts on the printed

circuit board.

• Always place the drive on top of or inside the antistatic bag to reduce the chance of

ESD damage

Preinstallation

Requirements

In addition to the contents included with your internal tape drive, you need the

following items to install your internal tape drive.

•AUSB2.0port

• 5.25-inch half-height bay (for internal drive)

• Backup application software that supports the internal tape drive. For a list of the

latest backup software applications tested with the internal DAT 320 tape drives,

please visit our Web site at http://www.quantum.com/ServiceandSupport/

Index.aspx#

Unpacking and

Inspecting the Drive

Before you unpack the contents of your drive package, inspect the shipping containers

for damage. If you spot damage to the container, notify your carrier immediately.

When you unpack the package, compare the items received with those on the packing

list. If any item is missing or damaged, please contact your place of purchase

immediately.

Installing the Internal DAT 320 Tape Drive in Your Server 3

DAT 320

Required Tools The following is a list of the tools you will need. You may need additional items,

depending on your installation requirements.

• Flat blade, Phillips or TORX screwdriver, depending on the type of screws used by

your computer

Installing the Internal DAT 320 Tape Drive in Your Server

Installing the internal DAT 320 tape drive consists of the following major steps:

•Preparing Mounting Bay

•Attaching Mounting Hardware

•Installing the Tape Drive

•Attaching the USB Cable

•Connecting the USB Cable from the Tape Drive to the Server

•Attaching the Power and USB Cables to the Tape Drive

•Securing the Drive

Preparing Mounting

Bay

Caution: To avoid personal injury or damage to the server or tape drive, ensure that

the server is disconnected from the main power supply while you install the

drive.

1Assemble the necessary tools and materials:

• Phillips screwdriver

2Perform a normal system shutdown and turn off the server and any connected

peripherals.

3Remove the cover and front panel from the server, as detailed in your server’s

documentation.

As you work inside the server, you may have to disconnect other signal cables or

power cables from other devices to maneuver the new drive into place. If you have

to do this, make a note of their position and connections so you can put them back

correctly later.

4You are now ready to install your tape drive.

Attaching Mounting

Hardware

If your server requires special rails or other hardware to install the tape drive, mount

them on the tape drive now. If your server does not require special mounting hardware,

proceed to Installing the Tape Drive.

4Installing the Internal DAT 320 Tape Drive in Your Server

DAT 320 Quick Start Guide

Caution: Static electricity can damage electronic components. Always wear an

antistatic wrist strap if one is available. If not, after you have disconnected

power from the server and removed the cover, touch a bare metal part of

the chassis. Similarly, touch a bare metal part of the drive before installing

it.

Note: If mounting hardware is supplied with your tape drive, it may not be exactly the

same as shown in the illustrations.

Different models of server require different mounting methods. The server may also

incorporate a locking mechanism to hold the tape drive in place.

Please check your server documentation to ascertain the correct method of mounting

and to check whether mounting hardware is provided with the server.

Mounting Rails

Some servers require mounting rails. These may be metal or plastic rails attached to the

filler panel of the server's drive bay.

1Use a regular Phillips screwdriver to attach the appropriate rails. Use M3 screws 5

mm (0.2 in).

Ensure you have the M3 screws. The rails may be attached to the filler panel by

screws of a different thread/size type and these should not be used. If in doubt,

refer to your server documentation.

Mounting Screws

Other server models only require the use of special locating screws with no mounting

rail.

1Use a screwdriver to attach the appropriate screws. You may need to purchase the

M3 screws separately. Position the screws (see Figure 1).

Figure 1 Attaching Mounting

Screws

Installing the Internal DAT 320 Tape Drive in Your Server 5

DAT 320

2Attach the appropriate mounting hardware. Refer to the manufacturer’s

documentation for instructions.

• If you are installing on a server that requires a tray, place the tape drive in the

tray.

• If you are installing in a server that requires mounting rails, fasten the rails to

the tape drive.

• Some servers have snap-on mounting rails attached to the filler panel. These can

be removed and attached to the tape drive with screws.

Installing the Tape Drive To install the tape drive:

1Slide the tape drive into the open bay aligning the tray or rails with the slots in the

bay (see Figure 2).

Figure 2 Installing the Tape

Drive

If your server does not use mounting hardware, check that the holes in the chassis are

aligned with the holes in the side of the tape drive.

Do not secure the drive at this point because you may have to move the drive to get the

cables into place.

6Installing the Internal DAT 320 Tape Drive in Your Server

DAT 320 Quick Start Guide

Attaching the USB

Cable

Decide Which Cable to Use

There are several options for connecting the tape drive to your server:

Connecting the USB

Cable from the Tape

Drive to the Server

To an Internal USB 2.0 Port

1Use the schematic on the inside of the server panel to check whether your server has

an internal USB 2.0 port and locate its position.

2Use the appropriate cable to connect to the server.

• A standard 5-pin USB Type B cable is provided with the tape drive (see Figure 3).

Figure 3 Connecting to an

Internal USB Port

To an . . . Use . . . Notes

Internal standard

USB port

standard

USB cable

May be connected to the server’s system board or

an internal USB card.

External USB port standard

USB cable

Cable routing kit is required.

Installing the Internal DAT 320 Tape Drive in Your Server 7

DAT 320

To a n E x t e r n a l U S B 2 . 0 P o r t

Purchase a special USB cable and Cable Routing Kit. The Cable Routing Kit consists of a

bracket with attached cable on one side that connects to the server’s external port and a

Type A USB socket on the other side. Make sure you orientate the bracket correctly when

you fit it (see Figure 4).

1Remove a spare blanking plate from the rear panel of the server.

2Fit the bracket with attached the cable and fix it to the server. Make sure the cable is

outside of the server and connect it to the server’s external USB port (see Figure 4).

3Attach the standard USB cable to the bracket (type A connector) (see Figure 4).

Figure 4 Connecting the USB

Cable

Attaching the Power

and USB Cables to the

Ta p e D r i v e

Note: The drive is not powered from the USB bus. It must be connected to the server's

power supply.

1Attach the USB cable to the tape drive (Type B connector).

Type B connector

to tape drive

Type A connector on

inside of bracket

Type A connector to

server’s external

USB port

8Installing the Internal DAT 320 Tape Drive in Your Server

DAT 320 Quick Start Guide

2Attach a spare cable from the server’s internal power supply to the power connector

(see Figure 5).

Figure 5 Attaching the Power

Cable

Securing the Drive Note: The server latches and side views of your server model may not be exactly the

same as shown in the illustrations. Please refer also to your server

documentation.

USB cable to server’s

external USB Port

Power cable

Tape drive

Server’s power supply

Installing the Internal DAT 320 Tape Drive in Your Server 9

DAT 320

Mounting Hardware Used

1Use M3 screws. Check that the holes in the chassis are aligned with the holes in the

sides of the drive and use a regular Phillips screwdriver to secure the M3 screws (see

Figure 6).

Figure 6 Securing Drive, No

Mounting Hardware Used

2Ensure blanking plates are in place over empty bays and replace the cover on the

server.

Completing Your

Installation

To complete and test your internal tape drive installation:

1Use the screws you removed earlier to secure the drive in place.

2Replace the computer cover.

3Reconnect the power cord to the computer’s power connector.

4Turn on the computer.

5If necessary install the DAT320 O/S driver.

6Install your backup software program. The documentation that came with your

software should describe this procedure.

7Gently insert a tape cartridge into the internal tape drive’s slot. Slide the cartridge

into the slot until the drive accepts the cartridge and loads it. A brief delay occurs

while the drive identifies the cartridge type and state, and moves the tape to the

data area. Then the green Ready LED goes ON.

8Use your backup software application to perform a sample backup-and-verify

operation. The Ready green LED flashes as data is written to and/or read from the

tape.

9At the end of the operation, press the Eject button on the front of the internal tape

drive to eject the cartridge from the drive.

M3 screws, supplied

with tape drive

10 Installing the Tabletop DAT 320 Tape Drive to Your System

DAT 320 Quick Start Guide

Installing the Tabletop DAT 320 Tape Drive to Your System

Installing the tabletop DAT 320 tape drive consists of the following major steps:

•Connecting the Power and USB Cables to Your Tabletop Drive

•Completing Your Installation

Connecting the Power

and USB Cables to Your

Tabletop Drive

Note: The drive is not powered from the USB bus. It must be connected to the main

power supply.

A power cable is provided with your Quantum DAT 320 tape drive.

1Make sure that the drive is switched OFF (O side down). The power switch is on the

rear panel.

2Connect the USB cable to the USB connector on the back of the enclosure.

3Plug the power cable securely into the socket on the rear panel of the drive and plug

the other end of the power cable into the power outlet.

Figure 7 Connecting Power

and USB Cables

4Plug the USB cable into the USB connector on the server.

Note: It is important to ensure that you connect your drive to a USB 2.0 port. The

drive will work on a USB 1.1 port but performance will be severely degraded.

Completing Your

Installation

To complete and test your tabletop tape drive installation:

1Use the On/Off Switch on the back of the tabletop tape drive to turn on the drive

(see Figure 7). The Ready LED should be ON, the other three front-panel LEDs should

be OFF.

USB cable

On/off switch

Power cable

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Quantum

Quantum

Quantum DXi3500 Manual técnico

Quantum

Quantum Scalar 218FC Manual de usuario

Quantum

Quantum Internal Storage System Travan 40 GB Manual de usuario

Quantum

Quantum DLT-S4 Manual de usuario

Quantum

Quantum DLT-V4 Manual de usuario

Quantum

Quantum DLTtape SDLT 600 Manual de usuario

Quantum

Quantum ValueLoader LTO-1 Manual de usuario

Quantum

Quantum ATL M1500 Manual de usuario

Quantum

Quantum DXi6900 Guía de inicio rápido

Quantum

Quantum StorNext QD7000 Manual de usuario

Quantum

Quantum DXi6900 Manual de usuario

Quantum

Quantum DLTtape SDLT 220 Hoja de información del producto

Quantum

Quantum DPM 5500 Manual de usuario

Quantum

Quantum StorNext QS1200 Manual técnico

Quantum

Quantum DXi4701 Manual de usuario

Quantum

Quantum Superloader 3 Manual de instrucciones

Quantum

Quantum SNC 5100 Manual de instrucciones

Quantum

Quantum ATL M2500 Manual de usuario

Quantum

Quantum LTO-9 HH SAS Manual de usuario

Quantum

Quantum StorNext QD7000 Manual

Quantum

Quantum StorNext QS1200 Manual de usuario

Quantum

Quantum Scalar i40 Instrucciones de funcionamiento y seguridad

Quantum

Quantum Scalar LTFS Manual de uso y cuidado

Quantum

Quantum DAT 160 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario