Quantum PX500 Series Guía de inicio rápido

81-81538-01 A01, December 2005 1

Quantum PX500 Series

TC2201 Upgrade Instructions

Introduction 3

TC2201 Bridge Operation ............................................................................ 3

Preparing for the TC2201 Installation 3

Required Upgrade Kits ................................................................................ 3

Required Equipment (Customer Supplied) .............................................. 3

Required Tools .............................................................................................. 3

TC2201 Upgrade Procedure 4

Preparing the Quantum PX500 Series Library ......................................... 4

Removing Tape Drive SCSI Cables ............................................................ 5

Installing the TC2201 Bridge ....................................................................... 8

Installing the Ethernet Cables ................................................................... 12

Installing SCSI Cables ................................................................................ 16

Configuring the TC2201 Bridge Software ............................................... 18

Saving the Configuration File ................................................................... 23

Zoning the Ethernet Switch 25

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

Made in the USA.

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to

the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to

time without notice.

Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of Quantum

Corporation is prohibited by law and constitutes a punishable violation of the law.

TRADEMARK STATEMENT

Capacity on Demand (CoD), Crosslink Mechanism, DLT, DLTSage, DLTtape, Super DLTtape, Performance on Demand, (PoD), PRISM,

PRISM Storage Architecture logo, SiteCare, StackLink, StorageCare, SuperLoader, and ValueLoader are all trademarks of Quantum

Corporation. Quantum, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation.

Other trademarks may be mentioned herein which belong to other companies.

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

Introduction 3

Introduction 0

The Quantum PX500 Series automated tape libraries are controlled by a host

computer via a SCSI LVD bus using the SCSI-3 medium changer command

set.

The Quantum PX500 Series allows for easy conversion from the SCSI host

interface to an iSCSI host interface. This document describes upgrading a

standard PX500 library equipped with a SCSI host interface to an iSCSI host

interface using a TC2201 Upgrade kit.

TC2201 Bridge

Operation 0Once a TC2201 bridge option is installed and tested, the library operates

exactly as a PX500 Series with a SCSI host interface. Operation of the library

via the operator control panel (OCP) is unchanged.

Preparing for the TC2201 Installation 0

Before beginning the installation procedure, make sure that you have the

required upgrade kit and tools.

Required Upgrade Kits 0The TC2201 installation requires the following upgrade kit for every two tape

drives in a PX500 Series library (see table 1):

Table 1 TC2201 Upgrade

Kit PN PR-UU9WG-YF

Required Equipment

(Customer Supplied) 0A zonable Ethernet switch is required if multiple TC2201 iSCSI bridges are

installed in either a PX506 or PX510 library. If a single TC2201 iSCSI bridge is

installed, an Ethernet switch is not required.

Required Tools 0The following tools are required to install the TC2201 bridge upgrade:

• #2 PHILLIPS® screwdriver

Note: All part numbers are subject to change without notice.

Qty Description

1 TC2201-LVD PWA

2 SCSI Cables

1Ethernetcable

1 Quantum PX500 Series TC2201 Upgrade Instructions

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

4 TC2201 Upgrade Procedure

TC2201 Upgrade Procedure 0

The upgrade procedure is identical regardless of the number of TC2201s

installed except where noted. The upgrade procedure consists of the

following major steps:

•Preparing the Quantum PX500 Series Library

•Removing Tape Drive SCSI Cables

•Installing the TC2201 Bridge

•Installing the Ethernet Cables

•Installing SCSI Cables

•Configuring the TC2201 Bridge Software

Preparing the

QuantumPX500Series

Library 0

To prepare the PX500 Series library:

1With the library turned on, press the Ops button on the OCP to access the

Operations screen (see figure 1).

Figure 1 Operations

Screen

2Select Library operations and press Enter.

3From the library operations menu, select Library on/offline and press Enter

to turn the library offline.

4Verify that the OCP display indicates “Offline” from the OCP screen.

5Turn off the power button located on the front of the library (see figure 2).

Caution: Use appropriate ESD procedures when assembling and

installing the TC2201 option.

Enter

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

TC2201 Upgrade Procedure 5

Figure 2 Turning On the

Library

Removing Tape Drive

SCSI Cables 0Each pair of tape drives within the library are connected via a SCSI cable.

These cables must be removed prior to cabling the TC2201.

1Locate the SCSI cables connecting each pair of tape drives in the library

and the host systems (see figure 3 for PX502, figure 4 for PX506, and

figure 5 for PX510). The tape drives are numbered 1 through 10

(depending on library model) starting in the top-right drive bay. Tape

drive 1 is in the upper right-hand drive bay, tape drive 2 is in the upper

left-hand drive bay, and so forth. Refer to the following illustrations for

exact tape drive numbering.

Power button

OCP

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

6 TC2201 Upgrade Procedure

Figure 3 PX502 Cabling

Configuration

Figure 4 PX506 Cabling

Configuration

Tape drive 2 Tape drive 1

SCSI

terminator

SCSI

cables

Host computer

SCSI

cable

SCSI cable

SCSI

terminators

SCSI cable

Tape drive 2 Tape drive 1

Tape drive 4

Tape drive 6 Tape drive 5

Tape drive 3

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

TC2201 Upgrade Procedure 7

Figure 5 PX510 Cabling

Configuration

2Remove all SCSI cables connecting each pair of tape drives and the host

systems and also all terminators.

Host computer

SCSI cable

SCSI

terminators

SCSI

cable

Host computer

SCSI

terminators

SCSI

cable

SCSI

cable

Tape drive 2 Tape drive 1

Tape drive 4

Tape drive 6 Tape drive 5

Tape drive 3

Tape drive 8 Tape drive 7

Tape drive 10 Tape drive 9

SCSI

cable

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

8 TC2201 Upgrade Procedure

Installing the TC2201

Bridge 0The number of TC2201 bridges required depends on the number of tape

drives installed in the library.

• 1 to 2 tape drives requires 1 TC2201

• 3 to 4 tape drives requires 2 TC2201 bridges (PX506 and PX510 only)

• 5 to 6 tape drives requires 3 TC2201 bridges (PX506 and PX510 only)

• 7 to 8 tape drives requires 4 TC2201 bridges (PX510 only)

• 9 to 10 tape drives requires 5 TC2201 bridges (PX510 only)

To install the TC2201 bridge:

1Loosen the two PHILLIPS screws securing the blank off plate(s) to the

CPCI card cage and expose the number of slots needed for the TC2201

installation (one blank off plate per TC2201).

2With the SCSI ports located to your right as you face the back of the

library, slide the first TC2201 into the slot of the card cage (see figure 6 for

PX502, figure 7 for PX506, and figure 8 for PX510).

Figure 6 Installing a

TC2201 Bridge (PX502)

Note: Start the TC2201 installation in slot 1 of the CPCI card cage

(PX506 and PX510 only).

Blank off plate

Screws

Card cage

TC2201

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

TC2201 Upgrade Procedure 9

Figure 7 Installing a

TC2201 Bridge (PX506) Blank off plate

Screws

Card cage

TC2201

Slot 1

Quantum PX500 Series TC2201 Upgrade Instructions

81-81538-01 A01

December 2005

10 TC2201 Upgrade Procedure

Figure 8 Installing a

TC2201 Bridge (PX510)

3Gently press down on the TC2201 until the board is seated in the card

cage and the ejector latches lock in place (see figure 9).

Blank off plate

Card cage

TC2201

Slot 1

Otros manuales para PX500 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Quantum

Quantum

Quantum DXi6902 Manual del operador

Quantum

Quantum SNC 4000 Manual de usuario

Quantum

Quantum StorNext QD6000 Manual de usuario

Quantum

Quantum Superloader 3 Manual de usuario

Quantum

Quantum P2000 Series Manual de usuario

Quantum

Quantum DLTtape DLT 4000 Manual de usuario

Quantum

Quantum RDX 8000 Manual de usuario

Quantum

Quantum Scalar i500 Manual de usuario

Quantum

Quantum DAT 160 Manual de usuario

Quantum

Quantum LTO3 A-Series Manual de usuario

Quantum

Quantum Atlas 10K III Manual de usuario

Quantum

Quantum DXi7500 Manual técnico

Quantum

Quantum DLTtape SDLT 220 Manual de usuario

Quantum

Quantum DXi4510 Manual del operador

Quantum

Quantum DXi4700 Manual de usuario

Quantum

Quantum Scalar i40 Instrucciones de funcionamiento y seguridad

Quantum

Quantum PowerStor L200 Manual de usuario

Quantum

Quantum QDFLD25-***MUH1I Series Manual de usuario

Quantum

Quantum DXi4701 Manual de usuario

Quantum

Quantum Scalar LTFS Manual de uso y cuidado

Quantum

Quantum P4000 Series Manual de usuario

Quantum

Quantum StorNext QD6000 Manual de usuario

Quantum

Quantum DXi4510 Manual del operador

Quantum

Quantum Scalar 50 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario