PureLink F1 Manual de usuario
Owner’s Manual
F1
Fiber Optic HDMI and USB Extension Modules
PureLinkTM
535 East Crescent Avenue
Ramsey, NJ 07446
USA
Tel: +1.201.488.3232
Fax: +1.201.621.6118
E-mail: sales@purelinkav.com
www.purelinkav.com
For order support, please contact your local dealer.
For technical support, please contact us at support@purelinkav.com
PureLink by Dtrovision
2
TABLE OF CONTENTS
Chapter 1. Product Overview
1.1 Safety Precautions --------------------------------------------------------------- 3
1.2 Product Description --------------------------------------------------------------- 4
1.3 Product Features --------------------------------------------------------------- 4
1.4 Common Application --------------------------------------------------------------- 4
1.5 What’s in the Box --------------------------------------------------------------- 5
1.6 Installation Guidelines --------------------------------------------------------------- 6
Chapter 2. Product Specifications
2.1 Electrical Specification --------------------------------------------------------------- 7
2.1-1 Transmitter Module ------------------------------------------------------------- 7
2.1-2 Receiver Module --------------------------------------------------------------- 8
2.1-3 HDMI Receptacle Pin Assignment ------------------------------------------ 8
2.2 Optical Specification --------------------------------------------------------------- 9
2.2-1 Transmitter Module --------------------------------------------------------------- 9
2.2-2 Receiver Module --------------------------------------------------------------- 9
2.3 Mechanical Specification ------------------------------------------------------------ 9
2.4 Environmental Specification ------------------------------------------------------- 10
2.5 System Requirements for Setup -------------------------------------------------- 10
2.6 Troubleshooting ----------------------------------------------------------------------- 10
2.7 Maintenance ------------------------------------------------------------------------- 11
2.8 UL/IEC Statement ----------------------------------------------------------------- 12
Chapter 3. Additional Information
3.1 Manufacturer’s Warranty (2-Year) ------------------------------------------------- 13
3.2 Customer Service ------------------------------------------------------------------- 13
PureLink by Dtrovision
3
Chapter 1. Product Overview
1.1 Safety Precautions
All safety instructions should be read and understood before the unit is operated.
The owner’s manual and safety instructions should be retained for future reference.
Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth only.
Keep away from wet, magnetic, and flammable surfaces or substances.
Always use the correct external power supply (indicated on the product label) when operating this unit.
This unit may be equipped with a 3 wire grounding-type plug - a plug having a third (grounding) pin.
This pin will only fit in to a grounding type power outlet. If you are unable to insert the plug in to the
outlet, contact your electrician to replace your obsolete outlet.
Air vents should be kept clean and unobstructed at all times.
Please refrain from using frayed power cords and damaged wall outlets.
Do not place any heavy objects or equipment on top of the unit.
If you experience any malfunctioning of product or have any question as to operation of the
product, please contact our customer service center.
PureLinkTM
Tel: 201.488.3232
Email: support@purelinkav.com
PureLink by Dtrovision
4
Welcome!
Congratulations on your purchase of the PureLink F1 Optical HDMI (High Definition Multimedia Interface) and
USB extension Modules. This manual contains information that will assist you in installing and operating the
product.
1.2 Product Description
The F1 fiber optical HDMI and USB extension module transmits Ultra-HD/4K HDMI v1.4b up to 300 meters
(1,000 ft), as well as USB up to 200 meters (650 ft), all over a single LC multi-mode fiber optic cable. The F1’s
compact size makes installation a snap, making it the most complete and reliable solution for long-distance
Ultra-HD/4K signal transmission.
1.3 Product Features
HDMI 1.4b compatibility: Ultra-HD/4K transport and extension
USB extension for full KVM operations
Single fiber provides 300 meters (1,000 ft) HDMI 4K distance
HDCP compliant
Support live EDID and HDCP handshake
Support USB 1.1
Styled casing with bottom mounting attachments
Maximum travel distance:
HDMI: 300 meters (1,000 ft)
HDMI + USB 1.1 Low speed: 200 meters (650 ft)
HDMI + USB 1.1 High speed 40 meters (135 ft)
*Common low speed device: Keyboard, mouse
*Common full speed device: External HDD, USB Hub, USB memory stick
1.4 Common Application
Self-service Ticketing Kiosks (airports, movie theaters, etc.)
Informational Kiosks (museums, galleries, exhibitions)
Bank ATMs
Digital Signage
Interactive White Boards
Conference System
Video Wall System
Medical, Broadcasting, Military
Factory Automation and Traffic Control System
PureLink by Dtrovision
5
1.5 What’s in the Box
F1 Optical HDMI Extension Module: One (1) pair (Tx, Rx)
5V AC-DC Adaptor [USB Type] : One (1) unit
USB cable : Two (2) units
0.5 meters (1.6ft) HDMI copper cable : Two (2) units
User’s Manual
Option Product: TWF1 (PureLink’s multi-mode 1 LC fiber optic cable with TotalWire Technology)
1.6 Product application notes
Figure 1 – Schematic Connection Diagram of F1 Extension Modules
Figure 2 – Schematic Connection Diagram of F1 Extension Modules
PureLink by Dtrovision
6
1.7 Installation
Important : Please use the installation procedure below. Improper or no operation may result if the
start up sequence is not correctly followed.
Step 1
Carefully unpack the contents of the shipping group
Step 2
Plug micro USB-B cable (labeled as TX) to the female micro USB receptacle of the transmitter and then
connect the other end of the USB type A cable to the video source’s USB port.
Step 3
Plug micro USB-B cable (labeled as RX) to the micro USB receptable of the receiver and then connect the
other end of the USB type A cable to the 5V power adopter.
Step 4
Connect female USB cable (labeled as RX) from the receiver to the USB peripheral device such as
keyboard, mouse, printer, USB hub etc.
Step 5
Connect LC optical fiber cable (multi-mode) between the transmitter and the receiver.
Step 6
Connect HDMI cable between the source and the transmitter.
Step 7
Connect HDMI cable between the display and the receiver.
Step 8
Turn power on the source and the display
PureLink by Dtrovision
7
Chapter 2. Product Specifications
2.1 Electrical Specification
Category
Detail spec
Electrical
Electrical Connector
HDMI Receptacle Type
Video band-width
2.97Gbps
Maximum Reach
HDMI : 300m
HDMI + Full Speed USB : 40m
HDMI + Low Speed USB : 200m
Graphic Resolution Support
4096x2160@30Hz
External Power Connector
Micro USB
Optical
Optical Connector
LC Connector
Recommended Fiber
50/125um Multi Mode Fiber [OM3]
TX Module
850nm VCSEL
1310 InGaAs/InP laser diode
1550 InGaAs/InP PIN type photo diode
RX Module
1550 InGaAs/InP laser diode
850 InGaAs/InP PIN type photo diode
1310 InGaAs/InP PIN type photo diode
2.1-1 Transmitter Module
PARAMETER
Min
Typ
Max
Unit
Supply Voltage
4.5
5
5.5
V
Supply Current
-
450
470
mA
Power consumption
-
0.85
1
W
TMDS Input Differential Voltage Level
150
1200
mV
TMDS Input Common Mode Voltage
2.9
3.26
V
TMDS Min Differential Sensitivity (Peak-to-Peak)
150
mV
TMDS Max Differential Input (Peak-to-Peak)
1560
mV
TMDS Max Allowable Intra-Pair Skew at Connector
0.15Tbit+112ps
TMDS Max Allowable Inter-Pair Skew at Connector
0.2 Tcharacter+1.78ns
TDR Rise Time
200
ps
PureLink by Dtrovision
8
2.1-2 Receiver Module
PARAMETER
Min
Typ
Max
Unit
Supply Voltage
4.5
5
5.5
V
Supply Current
-
400
420
mA
Power consumption
-
2
2.1
W
TMDS Single-ended output swing voltage
400
600
mV
TMDS Single-ended high level output voltage
3.3V-200mV
3.3V+10mV
TMDS Min Single-ended low level output voltage
3.3V-700mV
3.3V-400mV
TMDS Rise time/ fall time (20%-80%)
75
PS
TMDS Intra-Pair Skew at Source Connector
0.15Tbit
TMDS Inter-Pair Skew at Source Connector
0.2 Tcharacter
TDR Clock duty cycle
40%
50%
60%
TMDS Differential Clock Jitter
0.25Tbit
2.1-3 HDMI Receptacle Pin Assignment
HDMI Connector Pin Assignment
Pin No.
Signal Name
Pin No.
Signal Name
1
TMDS DATA 2+
11
TMDS Clock Shield
2
TMDS DATA Shield
12
TMDS Clock -
3
TMDS DATA 2-
13
CEC
4
TMDS DATA 1+
14
Reserved (HDMI 1.0–1.3c)
5
TMDS DATA Shield
15
SCL (I²C Serial Clock for DDC)
6
TMDS DATA 1-
16
SDA (I²C Serial Data Line for DDC)
7
TMDS DATA 01+
17
DDC/CEC/HEC Ground
8
TMDS DATA Shield
18
+5 V (max 50 mA)
9
TMDS DATA 0-
19
Hot Plug detect (all versions)
10
TMDS Clock +
20
2.2 Optical Specification
PureLink by Dtrovision
9
2.2-1 Transmitter Module
PARAMETER
Min
Typ
Max
Unit
Output Power 10G
-2.5
2.5
dBm
Output Power 1G
-5
2.5
dBm
Output Power 10G Extinction Ratio
3
dB
Output Power 1G Extinction Ratio
5.5
dB
Sensitivity
-20
dBm
2.2-2 Receiver Module
PARAMETER
Min
Typ
Max
Unit
Output Power 1G
-5
2.5
dBm
Extinction Ratio
5.5
dB
Output Power 10G Sensitivity
-20
dBm
Output Power 1G Sensitivity
-6
dBm
2.3 Mechanical Specification
Front : HDMI connector
Back : LC connector and Micro USB connector
2.4 Environmental Specification
PureLink by Dtrovision
10
Items
Status
Operating Temperature
32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity
10% ~ 80%, non-condensing
Storage Temperature
-4˚F ~ 158˚F (-20˚C ~ 70˚C)
Storage Humidity
5% ~ 95%, non-condensing
Dimension (WxDxH)
2.20’ x 2.20’ x 0.56’ (56mm x 56mm x 14mm)
Weight w/o Packaging
90g
Weight
400g
2.5 System Requirements for Setup
Hardware requirements
You have to have a HDMI graphic controller or card having a HDMI port in your PC, SUN or Mac
systems. It should support the maximum graphic resolution feature of displays to be connected.
No special requirements for memory size, CPU speed and chipsets, if you’ve already properly
installed your HDMI graphic controllers or cards.
Software requirements
No special restrictions, if you’ve already properly installed your HDMI graphic controller in your
OS.
AC/DC Power Adapter Technical Advisory
The transmitter (Tx) module of F1 is designed for power protection circuit from conflict of power
supply between the external DC power adapter and your graphic card through the HDMI pin. It
offers an option of whether to use an AC/DC power adapter depending on power supply capability
of the graphic card through the +5V pin, you are using.
However, the receiver (Rx) module should be supplied by an AC/DC power adapter.
Note : In general, most of laptops or desktop PCs with PCI Express graphic card supply
enough power to operate Transmitter (Tx) module.
Tabla de contenidos
Otros manuales de Extensor de PureLink
PureLink
PureLink Pure Stream VIP-200 Manual de usuario
PureLink
PureLink HW-100 Manual de usuario
PureLink
PureLink DTS-1000RV Manual de usuario
PureLink
PureLink PT-E-HD50 Manual de usuario
PureLink
PureLink RF6 Manual de usuario
PureLink
PureLink PM Series Manual de usuario
PureLink
PureLink PT-E-HD60 Manual de usuario
PureLink
PureLink FX1010 Manual de usuario
PureLink
PureLink PT-E-HD50 Manual de usuario
PureLink
PureLink WHD100-V2 Manual de usuario
PureLink
PureLink HOF1 Manual de usuario
PureLink
PureLink HOF2 Manual de usuario
PureLink
PureLink FIBERX FX-P350 Manual de usuario
PureLink
PureLink HCE III Manual de usuario
PureLink
PureLink HTE Tx Manual de usuario
PureLink
PureLink CSW030 Manual de usuario
PureLink
PureLink PureLink DTS50R Manual de usuario
PureLink
PureLink DS2200-060 Manual de usuario
PureLink
PureLink PM Series Manual de usuario
PureLink
PureLink DTE RX Manual de usuario
