PureLink VIP-100 II Manual de usuario

VIP-100 II

H.264 HDMI Extender over IP Extender

With LED, Remote, POE, RS232

User Manual

VIP-100 II Series H.264 Encoder Decoder User Manual

Introduction

The VIP100 II series incorportates the advanced H.264 codec as the

compression type, which makes it occupy lower bandwidth and transmit

over the LAN more smoothly. It supports 120m over single cat5e/6 cable at

point to point, as well as point to many and many to many over Ethernet

switch. The over IP solution is widely used in various locations, like meeting

room, class room, metro, airport, home, mall advertisement...etc.

1. Features

1). Using H.264 compression encoding, support resolution up to

1080p@60hz

2). Transmit up to 120m over single Cat5e/6 cable, with 1x looping HDMI

output

3). With IR Remote to choose the source, with LED to show the Group ID

4). Comply with TCP/IP protocol, streaming bit rate is up to 15Mbps

5). Support LPCM audio format

6). Smart IP Address Setting: Dynamic Host Configuration Protocol (DHCP)

7). Wide-band IR pass through to control the source (38khz to 56khz)

8). By pass 2 way UART/RS232 (Up to 115200), use remote controller to

select 8 group Baud rate

9). Support one to one, one to many, many to one, many to many modes,

with large cascade

10). Dual power input: 802.3af compliant POE & DC 5V (No need power

supply when connecting with POE Switch)

11). HDCP Compliant

12). Support PC tool control

13). DC 5V 1A power supply

2. 1 Specifications

Performance

Protocol H.264 encoder over TCP/IP

Support Video format 480i/480p/576i/576p/720p/1080i/1080p@60HZ

Support Audio format LPCM, Audio sampling rate 48KHZ

Streaming Bit Rate 15Mbps

HDCP Compliant

IR Frequency 38 -56 KHZ

RS232 Baud rate Default 2400bps, total 8 kinds optional

IP setting &Group ID setting

Default IP TX: 192.168.1.11 ; RX: 192.168.1.12

Group ID Group00-Group 99 (use remote controller)

Request for Switch/Router Support IGMP, support DHCP

Connectors on Transmitter

Input 1xHDMI Female port

Output 1x RJ45 output , 1x HDMI looping output

RS232 Phoenix RS232 port

IR IR TX port (Support 38K-56KHz)

IR Ext port (Support 38KHz)

Connectors on Receiver

Input 1xRJ45 input

Output 1x HDMI Female port looping output

RS232 Phoenix RS232 port

IR IR RX port (Support 38K-56KHz)

IR Ext port (Support 38KHz)

Environmental & Power Requirements

Operating temperature -5 to +35 ℃（+23 to +95℉）

Operating Humidity Range 5 to 90%RH (No Condensation)

Power supply DC 5V 1A

Power consumption Max 3 watt

Physical

Dimension TX: 119x79.5x28mm ; RX: 119x79.5x28mm

Net Weight TX: 0.28KG ; RX:0.28KG

VIP-100 II Series H.264 Encoder Decoder User Manual

2. 1 Supported input resolution

Frequency Resolution

50Hz

576i

576P

720P

1080P

1080i

60Hz/59.94Hz

480i

480P

720P

1080P

30Hz/29.97Hz 1080P

24Hz 1080P

25Hz 1080P

VESA Resolution

Frequency Resolution

60Hz

640×480

800×600

1024×768

1280×768

1280×960

1280×1024

1680×1050

1920×1080

1280×720

1360×768

1400×1050

VIP-100 II Series H.264 Encoder Decoder User Manual

3. Packing content

)

. 1x Transmitte

)

.1xReceiver

)

.1xIR-TXcable

)

. 1x IR-RX cable

5). 2X IR Ext Cable

)

. 1x Manual

)

.8xscrews

8). 4x detachable mounting ears

)

. 2x Phoenix plu

sfo

RS232 cable termination

)

. 2x Remote controlle

)

. 2x Power adapter 5V 1A

4. Panel description

1). TX

1) DC 5V 1A input 2) Green indicator of data status

3) Red indicator of power input 4) HDMI output for local display

5) HDMI input 6) CAT5e/6 output

7) IR-TX 8) RS232 port

9) IR-Ext 10) LED to show the Group ID

11) Press the button for the previous Group ID

12) Press the button for the next Group ID 13) Reset button

①The green LED will blink once the unit is working.

②The LED indicator will glow bright red once the power supply is

connected.

VIP-100 II Series H.264 Encoder Decoder User Manual

2). RX

1) DC 5V 1A input 2) Green indicator of data status

3) Red indicator of power input 4) HDMI output

5) CAT5e/6 input 6) IR-RX

7) RS232 port 8) IR-Ext

9) LED to show the Group ID

10) Press the button for the previous Group ID

11) Press the button for the next Group ID 12) Reset button

①The green LED will blink once the unit is working.

②The LED indicator will glow bright red once the power supply is

connected.

3). How to connect the IR Cable

Remote of the source

Remote of the HDMI extender

VIP-100 II Series H.264 Encoder Decoder User Manual

4.1. Panel Drawing

Transmitter

Receiver

VIP-100 II Series H.264 Encoder Decoder User Manual

5. Installation and Configuration

5.1 Setup HDMI TX and RX

When connecting point to point, no need to configure TX and RX,

When connecting point to many, many to point and many to many, please

make sure every TX and RX has unique IP and MAC address, every TX has

unique group ID.

Our this over IP Extender has been assigned unique default MAC address for

every TX and RX, so you don’t have to set the MAC for the units.

You just need to set the IP address and Group ID following bellowing steps.

5.1.1 Setting the IP address

A). DHCP (Dynamic host configuration protocol)

If you are using a Switch that supports DHCP, please enable DHCP so that

the Switch will assign an unique IP for TX and RX, and you don’t need to

change the IP fo

the units manually.

B). Set the IP via web browser

If you are using a Switch that doesn’t support DHCP, please change the

default IP for TX (192.168.1.11) and RX (192.168.1.12) manually.

HTTP server is embedded in each TX and RX. You can set up IP address

for HDMI Extende

via web browse

The default IP address of the TX is 192.168.1.11, use

name: admin,

password: admin

The default IP address of the RX is 192.168.1.12

VIP-100 II Series H.264 Encoder Decoder User Manual

Step 1: Make sure the Transmitter and PC are in the same domain.

ccess the Network Setting Control Panel in Windows and locate your

Lan connection. Under Windows 7, this can be done by clicking Start >

Control Panel >Network Sharing center>Change adapter settings >

Properties >Internet Protocol Version4 (TCP/IPv4). Change the IP address fi

eld to 192.168.1.1

(0-255).

fter that press "OK" to save the configuration.

※The PC and TX/RX should be in the same domain.

※The IP address of PC should be different from the IP address of

TX and RX.

Step 2: Use an Ethernet Cable to connect the PC (or laptop) and the

extender. the power LED for the extender is red and the green status is

blinking.

Step 3: Login in IE: 192.168.1.11 (default IP fo

TX) o

192.168.1.12(default

IP fo

RX), You can setup IP address fo

the TX and RX. TX requires user

name: admin and password: admin

Please set IP address for each TX and each RX, IP: 192.168.1.XX (XX:1-255.

all IP address for TX and RX must be different and can’t be same as the PC’s

address.)

Step 4: After selecting “Use DHCP” or reset the IP Address, click “Submit”

(transmitter) or “update DHCP” (Receiver).

Step 5: Click “Reboot”.

Step 6: Restart the extender after resting the IPAddress.

VIP-100 II Series H.264 Encoder Decoder User Manual

5.1.2 Choose the Group ID and Baud Rate by Remote controller

(When the LED shows “00”, it’s ready to work)

①Press the button, switch to

choose the Group ID or Baud rate.

②Factory reset. Press the button for

3 seconds, the LED will flicker then

turn to “00”, you have successfully

finished the factory reset.

Choose Group ID 00-63

1). Press “+” or “–” to change to the previous or next Group ID.

2). Press the No to change Group ID. For example, if you need change to 01,

press “0”, then press“1”.

Choose the Baud Rate

Press the Button, switch to Baud Rate mode, press “+” or “–” to change the

Baud Rate.

F0 = 2400

(

default

)

F1 = 4800

F2 = 9600

F3 = 19200

F4 = 28800

F5 = 38400

F6 = 57600

F7 = 115200

3). How to choose the source:

For example, when the connection is:

Source (DVD1) - TX (TX1) - Gigabit Switch – RX (RX1) - TV1

Source (DVD2) - TX (TX2) - Gigabit Switch – RX (RX2) - TV2

Source (DVD3) - TX (TX3) - Gigabit Switch

–

RX (RX3) - TV3

The group ID of transmitters is:

TX1 (01)

TX2 (02)

TX3 (03)

If you need display Source on TV1, then just set Group ID of RX1 same as

TX1: 01(see below picture).

TX 1 RX 1

VIP-100 II Series H.264 Encoder Decoder User Manual

Otros manuales para VIP-100 II

Otros manuales de Extensor de PureLink

PureLink

PureLink FX1010 Manual de usuario

PureLink

PureLink PureTools PT-HDBT-200 Manual de usuario

PureLink

PureLink PureMedia PM-CT101-U Manual de usuario

PureLink

PureLink DTS-1000RV Manual de usuario

PureLink

PureLink HOF1 Manual de usuario

PureLink

PureLink DTE RX Manual de usuario

PureLink

PureLink PureLink DTS50R Manual de usuario

PureLink

PureLink WHD100-V2 Manual de usuario

PureLink

PureLink PT-E-HD60 Manual de usuario

PureLink

PureLink DCE II Manual de usuario

PureLink

PureLink HWCE-III Manual de usuario

PureLink

PureLink HEXA PRO Manual de usuario

PureLink

PureLink Fiber Optic Extenders Manual de usuario

PureLink

PureLink WHD030-V2 Manual de usuario

PureLink

PureLink VIP-101-E-WP Manual de usuario

PureLink

PureLink FIBERX FX-P350 Manual de usuario

PureLink

PureLink DVI Pure Fiber Optic Extender Dual LinkODC Manual de usuario

PureLink

PureLink CSW030 Manual de usuario

PureLink

PureLink DS2200-060 Manual de usuario

PureLink

PureLink Media Axis HDBaseT MAX-CT101 Manual de usuario

PureLink

PureLink HWCE TX Manual de usuario

PureLink

PureLink PT-E-DV30 Manual de usuario

PureLink

PureLink HOF2 Manual de usuario

PureLink

PureLink PM Series Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario