PROAIM GP-FTGP-01 Manual de usuario
1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
2 x Small Sucon Cup
with Dust Cover (Black)
What’s In The Box
Fistgrip Car Mount with Shock Absorbing System
(GP-FTGP-01)
Assembly Manual
1 x Spanner (Size:13)
1 x L-Type Allen key (4mm)
4 x Dovetail Plates
8 x Counterweight
1 x Large Sucon Cup with
Dust Cover (Yellow)
4 x Shock-Absorbing
Adapter
Shock-Absorbing Arm Shock-Absorbing Head with
2 x V-Mount Baery Plate
2
Fistgrip Car Mount Setup
• Remove the blue dust cover of the Sucon
Car Mount.
NOTE: All sucon cups come with dust covers to
protect grippers from dust & provide maximum
surface adhesion.
• Mount a dovetail plate on the sucon cup
and properly aach it.
• Press down the sucon cup and keep pushing
the pump to rmly x it onto the car surface.
Repeat this process for all the sucon cups.
Cauon: Recheck the Pump every 90 minutes. If
the red line is visible, re-pump the cup without
losing the remaining vacuum ll the red line
disappears.
• Loosen the castle ring of a sucon cup and
remove it, as shown in the image.
• Similarly, follow the same process for the
other sucon cups.
2 x Safety Belt (Pair)
Flight Case
P-QRG
1 x DJI - QR Plate
3
• Tighten the assembly with the castle ring and
also, tighten and attach the other rings.
• Properly tighten the castle ring with the help
of the Allen key, as shown in the image.
• Loosen the center castle ring of the dovetail
plate, and then remove it.
• Loosen the knob of the adapter on the plate.
• Change the posion of the adapter
accordingly, and then re-ghten the knob.
• Mount the dovetail plate properly by aligning
it with the adapter.
NOTE: Multiple free holes have been provided
in the dovetail plate. The dovetail plates come
with mulple built-in expansion screws to
exibly link the plates together to achieve any
desired shoong angle possible.
4
• Secure it with the castle ring, and then
tighten it using the Allen key.
• Loosen the knob on the dovetail plate and
then push the push-pin button of the other
plate.
• Attach the dovetail plate by sliding it onto the
other plate.
• After attaching the plate, secure & tighten
the assembly via the knob on the plate.
• Loosen the knob present on the other end
and then slide the other plate to join both the
plates.
• Retighten the knob of the dovetail plate, as
shown in the image.
5
• Remove the yellow dust cover of Sucon Car
Mount.
• Loosen and remove the castle ring on the
sucon cup.
• Insert the suction cup into the end hole of the
dovetail plate, and then mount it on your
vehicle’s bonnet.
• Press down the sucon cup and keep pushing
the pump to rmly x it on the surface.
• Now secure the assembly using the castle
ring.
• Tighten the castle ring using the Allen key, as
shown in the image.
Larger Secon Cup Assembly
6
• Loosen and remove the castle ring of the
shock absorbing arm.
• Match the shock absorbing arm to the free
holes of the dovetail plate, and then insert it.
Secure it from the back end of the dovetail
plate using the castle ring.
• Loosen the spring tension knob of the shock
absorbing arm.
• Align & insert the shock absorbing head into
the arm.
• Tighten and secure the assembly using the
castle ring.
• Aach DJI-QR plate to the boom plate of the
shock absorbing head.
7
• Secure and lock the assembly with the help of
provided locking lever.
• Match the threads of the shock absorbing
head with DJI-QR plate to insert the bolts and
then tighten them using the Allen key.
• Insert the gimbal (Not Included) by sliding it
along the DJI-QR plate.
• Attach the battery (Not Included) by sliding it
onto the battery plate of the shock absorbing
head.
• One of the safety belts has a hook, while the
other has both a hook and a ratchet.
Lock lever
• Then aach the (P-QRG) plate with Ronin
Gimbal (Not Included) and ghten it properly
with the help of a screw driver.
8
• It lets you set up your camera in a multude
of posions onto the car through a smartly
featured modular dovetail mounng frame
and enhanced sucon system.
NOTE: Test all xtures before driving.
• Insert the safety belt into one of the holes of
the dovetail plate and then e it into a strong
knot.
• Insert the other end of the belt into the
ratchet, as shown in the image.
• Fasten the hook onto your vehicle.
• Tighten the belt using the ratchet, as shown
in the image.
NOTE: The System has a safety belt that secures
the components from slipping o.
• Follow the same procedure to aach second
safety belt (pair).
NOTE: Although the sucon cup holding force is
adequate for regular driving shots, you must
use safety belts/tension straps for addional
security. When mounted on cars, properly
secure the Fistgrip Car Mount aached to the
sucon cup (e.g. camera, gimbal, etc.) Tighten
safety straps carefully to prevent damages.
9
YOUR PROAIM FISTGRIP CAR MOUNT WITH SHOCK ABSORBING SYSTEM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon and
evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.
NOTE: It has two cable blocks to support the
gimbal and absorb ineral moon. And any of
them can be used in range of load capacity of
heavy & light ranged.
Otros manuales de Rack y soporte de PROAIM
PROAIM
PROAIM P-BMMT-01 Manual de usuario
PROAIM
PROAIM AP-PTP-SCSR Manual de usuario
PROAIM
PROAIM CM-ISGP-01 Manual de usuario
PROAIM
PROAIM SnapRig GP205 Manual de usuario
PROAIM
PROAIM VCTR-CM Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM P-GMBC-01 Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM CINEMA P-GH-30 Manual de usuario
PROAIM
PROAIM SS-CT Manual de usuario
