Planet IGS-824UPT Manual de usuario
Industrial 4-Port 10/100/1000BASE-T 802.3bt PoE + 2-Port
10/100/1000T + 2-Port 100/1000X SFP Ethernet Switch
IGS-824UPT
User's Manual
Table of Contents
1. Package Contents................................................................................. 3
2. ProductSpecications ........................................................................... 4
3. Hardware Introduction .......................................................................... 6
3.1 Switch Front Panel......................................................................... 6
3.2 LED Indicators............................................................................... 7
3.3 Switch Upper Panel........................................................................ 9
3.4 Wiring the Power Inputs................................................................. 9
3.5 Wiring the Fault Alarm Contact ..................................................... 11
3.6 Grounding the Device................................................................... 11
4. Installation ........................................................................................ 12
4.1 DIN-rail Mounting Installation ....................................................... 12
4.2 Wall-mount Plate Mounting ........................................................... 13
Customer Support.................................................................................... 14
3
1. Package Contents
Thank you for purchasing PLANET IGS-824UPT Industrial 8-Port Gigabit
Ethernet Switch with 4-Port PoE++. The interfaces of this model are shown
below:
Model Name 10/100/1000T RJ45 Port 100/1000X SFP Slot PoE Port
IGS-824UPT 6 2 4
In the following section, the term “Industrial PoE++ Switch” means the
IGS-824UPT.
Open the box of the Industrial PoE++ Switch and carefully unpack it. The box
should contain the following items:
Industrial PoE++ Switch x 1 User’s Manual x 1 DIN-rail Kit x 1
Wall-mount Kit x 1 RJ45 Dust Cap x 6 SFP Dust Cap x 2
If any of these are missing or damaged, please contact your dealer
immediately.
4
2.ProductSpecications
Model IGS-824UPT
HardwareSpecications
Copper Ports 6 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP Slots 2 1000BASE-SX/LX/BX SFP interfaces
Compatible with 100BASE-FX SFP
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1
Pin 3/4 for fault alarm
Pin 5/6 for Power 2
Alarm One relay output for power failure.
Alarm relay current carry ability: 1A@DC 24V
Power Requirements
48~54V DC, 5A (max.)
Redundant power with reverse polarity protection
function
Power Consumption Max. 3.24 watt/11.06 BTU (Idle)
Max. 250 watt/853.04 BTU (Full load)
Dimensions
(W x D x H) 55 x 85 x 135 mm
Weight 777g
Enclosure IP30 aluminum case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
SwitchSpecications
Switch Architecture Store-and-Forward
Switch Fabric 16Gbps
Throughput
(packet per second) 11.9Mpps@64bytes
Address Table 4K entries
BuerMemory 4Mbitson-chipbuermemory
Jumbo Frame 9K bytes
5
Flow Control Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Power over Ethernet
PoE Standard IEEE 802.3bt PoE++ type 4 PSE
Backward compatible with IEEE 802.3at PoE+ PSE
PoE Power Supply Type
802.3bt
Legacy/Force
End-span/Mid-span
PoE Power Output
Max. 95 watts to 802.3bt PoE++ PD
Max. 95 watts to Legacy/Force PD
Max. 36 watts to 802.3at PoE+ PD
Power Pin Assignment
End-span: 1/2(-), 3/6(+)
Mid-span: 4/5(+), 7/8(-)
802.3bt/PoH: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE Power Budget 240 watts maximum@52-54V DC input
160 watts maximum@48-51V DC input
Standard Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3az Gigabit SX/LX
IEEE 802.3x Full-Duplex Flow Control
IEEE802.3azEnergyEcientEthernet (EEE)
IEEE 802.3bt Power over Ethernet Plus Plus
IEEE 802.3at Power over Ethernet Plus PSE
IEEE 802.1p Class of Service
Environment
Temperature Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
6
3. Hardware Introduction
3.1 Switch Front Panel
4
2
3
65
1
IGS-824UPT
802.3bt PoE++
P1 P2 Alarm
80W 160W 240W
PoE
Usage
ACTLNK
PoE-in-Use
1000 LNK/ACT
10/100 LNK/ACT
78
7
8
Legacy
ON
Standard
OFF
PoE Mode
1
2
3
4
DIPON
2
3
4
1
1. PoE Mode Switch
Standard Mode: Fully conforms to the IEEE
802.3af/at/bt standard.
Legacy Mode: Identify and power non-
standard PD devices.
2. Gigabit Ethernet PoE++ Interfaces
802.3bt PoE++ 10/100/1000BASE-T
copper, RJ45 twisted-pair: Up to 100
meters.
3. Gigabit Ethernet TP Interfaces
10/100/1000BASE-T copper, RJ45 twisted-
pair: Up to 100 meters.
4. 100/1000BASE-X SFP Slot
The SFP slots built in the IGS-824UPT
supports SFP auto-detection and dual
speed as it features 1000BASE-SX/LX/
BX and 100BASE-FX SFP (small form-
factor pluggable) fiber-optic modules.
The distance can be extended from 550
meters to 2 kilometers (multi-mode fiber)
and 10/20/40/60/80/120 kilometers
(single-mode fiber or WDM fiber).
Figure 1: IGS-824UPT
Front View
Details of PoE Mode
PoE Mode Description
Standard
(Default)
The Standard mode is to provide power to the PD device that
follows the IEEE 802.3af/at/bt standard.
Legacy The Legacy mode supports Ultra PoE. It is to provide power to the
PD devices that do not fully follow the IEEE 802.3af/at/bt standard.
7
The IGS-824UPT also supports Force Power Mode in the Legacy
mode. If the output power of IGS-824UPT in the Legacy Mode is
less than 1 watt for 20 seconds, the Force Mode will be enabled
for 2 seconds. If the loading is still less than 1 watt, the Legacy
Mode will be enabled again.
The IGS-824UPT in the Force Mode will also provide a maximum
95-watt power to the PD. TO PREVENT THE DEVICES FROM
DAMAGE, please make sure the remote devices supports either
the Legacy or Force Mode before turning the DIP switch to the
Legacy Mode.
Only adjust the DIP switch to the desired mode before
powering on the IGS-824UPT. Power off first before changing
mode.
3.2 LED Indicators
System
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
Alarm Red Lights to indicate either power 1 or power 2 has no power.
PoE Power Usage (Unit: Watt)
LED Color Function
80W Amber
Blinks to indicate that the PoE usage is around 40W to
79W.
Lights to indicate the PoE usage is around/over 80W.
160W Amber
Blinks to indicate that the PoE usage is around 120W to
159W.
Lights to indicate the PoE usage is around/over 160W.
240W Amber
Blinks to indicate that the PoE usage is around 200W to
239W.
Lights to indicate the PoE usage is at the maximum.
8
Per 802.3bt PoE++ 10/100/1000BASE-T Interface (Port 1 to Port 4)
LED Color Function
LNK/ACT Green
Lights to indicate the link through that port is
successfully established at 10Mbps or 100Mbps or
1000Mbps.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.
PoE-in-Use Amber
Lights to indicate the port is providing DC in-line
power.
O to indicate the connected device is not a PoE
powered device (PD).
Per 10/100/1000BASE-T Interface (Port 5 and Port 6)
LED Color Function
1000
LNK/ACT Green
Lights to indicate the port is successfully established at
1000Mbps.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.
10/100
LNK/ACT Amber
Lights to indicate the port is successfully established at
100Mbps or 10Mbps.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.
Per 1000BASE-X SFP Slot (Port 7 and Port 8)
LED Color Function
1000
LNK/ACT Green
Lights to indicate the port is successfully established at
1000Mbps.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.
100
LNK/ACT Amber
Lights to indicate the port is successfully established at
100Mbps
Blinks to indicate that the Switch is actively sending or
receiving data over that port.
9
3.3 Switch Upper Panel
The upper panel of the Industrial PoE++ Switch consists of one terminal block
connector within two DC power inputs.
Figure 3-2 shows the upper panel of the Industrial PoE++ Switch.
DC Input:
48-54V , 5A max.
PWR1 PWR2
Alarm
Max. Fault Alarm loading: 24V, 1A
1 2 3 4 5 6
Figure 3-2: Industrial PoE++ Switch Upper Panel
3.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial PoE++
Switch is used for two DC redundant power inputs. Please follow the steps
below to insert the power wire.
Caution
When performing any of the procedures like inserting the wires
or tightening the wire-clamp screws, make sure the power is
OFF to prevent from getting an electric shock.
1. The DC power input range is 48V ~ 54V DC. Please insert positive and
negative DC power wires into contacts 1 and 2 for POWER 1, or 5 and 6 for
POWER 2.
DC Input:
48-54V , 5A max.
PWR1 PWR2
Alarm
Max. Fault Alarm loading: 24V, 1A
1 2 3 4 5 6
Figure 3-3: Industrial PoE++ Switch DC Input
10
DC Input Max. PoE Budget
48~51V 160W
52V~54V 240W
Note
1. To avoid damage, please use the Industrial PoE++ Switch
accordingtoitsspecications.
2. Please follow the table above for DC input in relation with
maximum PoE budget.
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
Power 1 Alarm Power 2
+ - + -
Note
The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
PWR1 and PWR2 must provide exactly the same DC voltage
for power load balance while operating with dual power input.
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet GSW-1601 Manual de usuario
Planet
Planet GSW-2416SF Manual de usuario
Planet
Planet TSN-6325-8T4S4X Manual de usuario
Planet
Planet IGS-10020M Manual de usuario
Planet
Planet IFGS-1022HPT Manual de usuario
Planet
Planet IGS-10020PT Manual de usuario
Planet
Planet FGSD-910P Manual de usuario
Planet
Planet WGSW-20160HP Manual de usuario
Planet
Planet GS-4210-8UP2S Manual de usuario
Planet
Planet FSD-1008HP Manual de usuario
Planet
Planet HPOE-1200G Manual de usuario
Planet
Planet EH-1600 Manual de usuario
Planet
Planet XGS-6320-8X8TR Manual de usuario
Planet
Planet EMQ-SGS-5240 Series Manual de usuario
Planet
Planet LRP-422CST Manual de usuario
Planet
Planet FSD-804P Manual de usuario
Planet
Planet UPOE-1600G Manual de usuario
Planet
Planet FNSW-1600 Manual de usuario
Planet
Planet POE-400 Manual de usuario
Planet
Planet IGS-10020HPT-U Manual de usuario
