Planet IGS-5225-4T2S Manual de usuario
Industrial L2+ Multi-Port Full Gigabit
Managed Ethernet Switch
IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-4UP1T2S
IGS-5225-8P4S/IGS-5225-8P4S-12V/IGS-5225-8P2T2S
IGS-5225-8P2T4S
Quick Installation Guide
Table of Contents
1. Package Contents................................................................................. 3
2. Requirements....................................................................................... 5
3. Wiring the Power Inputs ....................................................................... 6
3.1 Grounding the Device..................................................................... 8
4. Terminal Setup..................................................................................... 9
4.1. Logging on to the Console............................................................ 10
4.2 ConguringIPAddress ................................................................. 11
5. Starting Web Management .................................................................. 13
5.1 Logging in to the Industrial Managed Switch .................................. 13
5.2 SavingCongurationviaWeb ....................................................... 15
6. RecoveringBacktoDefaultConguration ............................................. 16
7. Customer Support .............................................................................. 19
3
1. Package Contents
Thank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-5225
Series. The number of the ports of these models is as follows:
GbECopper
Ports
PoEPorts GbESFPPorts
at/af bt* 1G 2.5G*
IGS-5225-4T2S 4- - - 2
IGS-5225-4P2S 4 4 -2-
IGS-5225-4UP1T2S 5-4-2
IGS-5225-8P4S 8 8 -2 2
IGS-5225-8P4S-12V 8 8 -2 2
IGS-5225-8P2T2S 10 8- - 2
IGS-5225-8P2T4S 10 8-2 2
*bt:Compatiblewith802.3at/afPoE
*2.5G:Compatiblewith1000BASE-SX/LX/BXSFPtransceiver
“Industrial Managed Switch” mentioned in this Quick Installation Guide
refers to the above models.
4
Open the box of the Industrial Managed Switch and carefully unpack it.
The box should contain the following items for each model of the Industrial
Managed Switches:
The
Industrial
Managed
Switch
Quick
Installation
Guide
Sheet
Wall
Mounting
Kit
DB9 to
RJ45,
RS232
Console
Cable
RJ45
Dust
Cap
SFP
Dust
Cap
IGS-5225-
4T2S 5 2
IGS-5225-
4P2S 5 2
IGS-5225-
4UP1T2S 6 2
IGS-5225-
8P4S 9 4
IGS-5225-
8P4S-12V 9 4
IGS-5225-
8P2T2S 11 2
IGS-5225-
8P2T4S 11 4
If any of these are missing or damaged, please contact your dealer
immediately. If possible, retain the carton including the original packing
materials to enable you to repack the product in case there is a need to return
it to us for repair.
5
2. Requirements
The Industrial Managed Switch provides remote login interface for
management purposes. The following equipment is necessary for further
management:
zWorkstations running Windows 10/11, MAC OS 10.15 or later, Linux, UNIX,
or other platforms are compatible with TCP/IP protocols.
zWorkstationsareinstalled withEthernetNIC(NetworkInterfaceCard)
zSerialPortConnection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such
as putty or tera term.
Serial cable -- one end is attached to the RS232 serial port, while the
other end to the console port of the Industrial Managed Switch.
zEthernetPortConnection
Network cables -- Use standard network (UTP) cables with RJ45 connec-
tors.
The above PC is installed with Web browser.
It is recommended to use Chrome 98.0.xxx or above to access
the Industrial Managed Switch.
6
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch comes with one
6-contact terminal block. Please follow the steps below to insert the power
wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1,
or Contacts 5 and 6 for Power 2.
IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S:DC48~54V
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S Upper Panel
IGS-5225-4UP1T2S:DC48~54V
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 8.3A max.
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
PWR1 Alarm PWR2
V1+ V2+
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Earth Ground
Figure 3-2: IGS-5225-4UP1T2S Upper Panel
IGS-5225-4T2S:DC12~48V,AC24V
Max. Fault Alarm Loading: 24V, 1A
DC Input: 12-48V
, 1.7A max.
AC Input: 24V
, 1A max.
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3-3: IGS-5225-4T2S Upper Panel
7
IGS-5225-4P2S:DC48~56V
FaultPWR1
V1+ V2+
PWR2
Max. fault loading: 24V, 1A
DC Input: 48-56V
,
3.5A max.
1 2 3 4 5 6
Figure 3-4: IGS-5225-4P2S Upper Panel
IGS-5225-8P4S-12V:DC12~54V
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
12-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-5: IGS-5225-8P4S-12V Upper Panel
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
123456
V+ V- V+ V-
Power 1 Power 2
Positive(+)Pin Negative(-)Pin
IGS-5225Series Pin 1/5 Pin 2/6
8
1. The wire gauge for the terminal block should be in the range
from 12 to 24 AWG.
2.Please check the wire AWG Ampere specification before
connectingPLANETIndustrialManagedSwitch.
PWR1 and PWR2 must provide the same DC voltage for pow-
er load balance while operating with dual power input.
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
EMD(Lightning)damageisnotcoveredunderwarranty.
9
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type serial (console) port of the Industrial
Managed Switch. The console port of the Industrial Managed Switch is DCE
already, so that you can connect the console port directly through PC without
the need of null modem.
PC/Workstation with
Terminal Emulation Software
RJ45 to DB9 RS232 Cable
Serial Port
Console Port
115200,N,8,1
IGS Industrial Managed Switch
11
Console
115200,N,8,1
P1 P2 Fault
DIDO
Ring
11
R.O.
12
12
PoE Usage
ACT1000 LNK
ACT100 LNK
A terminal program is required to make the software connected to the
IGS-5225seriesIndustrialManagedSwitch.
1. Run terminal program on the OS.
2.When the followingscreenappears,makesurethatthe COM port should be
conguredas:
Baud: 115200
Parity:None
Data bits: 8
Stop bits: 1
Flowcontrol:None
10
4.1. Logging on to the Console
Once the terminal has been connected to the device, power on the Industrial
Managed Switch and the terminal will display “running testing procedures”.
The following console screen is based on the IGS-
5225-4UP1T2S. The display of the other IGS-5225 series is the
sameasthatoftheIGS-5225-4UP1T2S.
Then, the following message asks to log in user name and password. The
default user name and password are shown as follows and the login screen in
Figure4-1appears
Username:admin
Password: admin
Figure 4-1: Console Login Screen
The user can now enter commands to manage the Industrial Managed Switch.
For a detailed description of the commands, please refer to the following
chapters.
1.For security reason, please change and memorize the
new password after this first setup.
2. Only accept command in lowercase letter under console inter-
face.
Otros manuales para IGS-5225-4T2S
2
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet DH-1600 Manual de usuario
Planet
Planet POE-1200 Manual de usuario
Planet
Planet MGSD-10080F Manual de usuario
Planet
Planet IPM-4220 Manual de usuario
Planet
Planet GSW-1600HP Manual de usuario
Planet
Planet GS-5220-8UP2T2X Manual de usuario
Planet
Planet WGSD-8020P Manual de usuario
Planet
Planet IGS-824UPT Manual de usuario
Planet
Planet WS-1032P Manual de usuario
Planet
Planet NOVASwitch FNSW-8086F Manual de usuario
Planet
Planet IKVM-8020 Manual de usuario
Planet
Planet IAP-2000PE Manual de usuario
Planet
Planet XGS-6311 Series Manual de usuario
Planet
Planet GSD-800S Manual de usuario
Planet
Planet WGSW-52040 Manual de usuario
Planet
Planet UPOE-1600G Manual de usuario
Planet
Planet FSD-808HP Manual de usuario
Planet
Planet GSW-1820HP Manual de usuario
Planet
Planet IGS-4215 Series Manual de usuario
Planet
Planet WGSW-48040HP Manual de usuario
