Planet IGS-501T Manual de usuario
5-/8-Port 10/100/1000Mbps
Industrial Gigabit Ethernet Switch
IGS-501T/IGS-801T
User's Manual
Table of Contents
1. Package Contents...................................................................... 3
2. Hardware Introduction ............................................................... 4
2.1 Physical Dimensions ............................................................ 4
2.2 Switch Front Panel.............................................................. 6
2.3 LED Indicators.................................................................... 7
2.4 Switch Upper Panel............................................................. 8
2.5 Wiring the Power Inputs...................................................... 8
2.6 Wiring the Fault Alarm Contact ............................................ 9
2.7 ProductSpecications ........................................................10
3. Installation ..............................................................................12
3.1 DIN-rail Mounting Installation .............................................12
3.2 Wall-mount Plate Mounting .................................................13
4. Troubleshooting ........................................................................15
5. Customer Support ....................................................................16
APPENDIX A: Networking Connection...............................................17
A.1 Switch’s RJ45 Pin Assignments ............................................17
A.2 RJ45 Cable Pin Assignments................................................18
3
1. Package Contents
Thank you for purchasing PLANET 5-/8-Port 10/100/1000T industrial
Gigabit Ethernet Switch, IGS-501T and IGS-801T. In the following
section, the term “Industrial Gigabit Ethernet Switch” means the
IGT-501T/IGT-801T.
Open the box of the Industrial Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Industrial Gigabit Ethernet Switch x 1 User's Manual x 1
DIN Rail Kit x 1 Wall-mount Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
4
2. Hardware Introduction
2.1 Physical Dimensions
IGS-501T dimensions (W x D x H): 135 x 87 x 32mm
Dimensions ( unit = mm )
Side View
Bottom View
Front View
Top View
Rear View
32.00
135.00
87.80
97.10
48.8046.50 39.70
87.80
53.50 53.50
18.00
15.20
30.00
9.20
5
IGS-801T dimensions (W x D x H): 135 x 87 x 32mm
Dimensions ( unit = mm )
Side View
Bottom View
Front View
Top View
Rear View
P1 P2 FAULT
1
2
3
4
5
6
7
8
ACT
LNK
ACT
LNK
1000
100
IGS-801T
Input
DC12~48V, AC 24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
6
2.2 Switch Front Panel
The front panel of the Industrial Gigabit Ethernet Switch consists of
5 or 8 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED
Indicators are also located on the RJ45 ports of the Gigabit Ethernet
Switch.
Figures 2-1 and 2-2 show the front panels of Industrial Gigabit
Ethernet Switches.
P1 P2 FAULT
1
2
3
4
5
6
7
8
ACT
LNK
ACT
LNK
1000
100
IGS-801T
Figure 2-1: IGS-501T Front Panel Figure 2-2: IGS-801T Front Panel
7
2.3 LED Indicators
IGS-501T:
LED Color Function
P1 Green Lit: indicates power 1 has power.
P2 Green Lit: indicates power 2 has power.
FAULT Green Lit: indicates either power 1 or power 2 has no power.
1000 Green
Lit: indicates the port is successfully connecting to
the network at 1000Mbps.
Off: indicates that the port is successfully connecting
to the network at 10Mbps or 100Mbps.
Blinking: indicates that the port is actively sending
or receiving data.
100 Green
Lit: indicates the port is successfully connecting to
the network at 100Mbps or 10Mbps.
Off: indicates that the port is successfully connecting
to the network at 1000Mbps.
Blinking: indicates that the port is actively sending
or receiving data.
IGS-801T:
LED Color Function
P1 Green Lit: indicates power 1 has power.
P2 Green Lit: indicates power 2 has power.
FAULT Red Lit: indicates either power 1 or power 2 has no power.
1000 Green
Lit: indicates the port is successfully connecting to
the network at 1000Mbps.
Off: indicates that the port is successfully connecting
to the network at 10Mbp or 100Mbps.
Blinking: indicates that the port is actively sending
or receiving data.
100 Orange
Lit: indicates the port is successfully connecting to
the network at 100Mbps or 10Mbps.
Off: indicates that the port is successfully connecting
to the network at 1000Mbps.
Blinking: indicates that the port is actively sending
or receiving data.
8
2.4 Switch Upper Panel
The upper panel of the Industrial Gigabit Ethernet Switch consists of
one terminal block connector within two DC power inputs.
Figure 2-3 shows the upper panel of the Industrial Gigabit Ethernet
Switch.
Figure 2-3: Industrial Gigabit Ethernet Switch Upper Panel
2.5 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial
Gigabit Ethernet Switch is used for two DC redundant power inputs.
Please follow the steps below to insert the power wire.
1. Insert positive and negative DC power wires into contacts 1 and 2
for Power 1 or 5, and 6 for Power 2.
V1+ V1- V2+ V2-
9
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
123456
Power 1 Fault Power 2
+ - + -
Note
1 The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. The device must be grounded.
3. The DC power input range is 12V ~ 48V DC.
2.6 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the
Industrial Gigabit Ethernet Switch will detect the fault status of the
power failure and then forms an open circuit. The following illustration
shows an application example for wiring the fault alarm contacts.
Insert the wires into the fault alarm contacts
10
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 30V, max. 3A
currents.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
2.7 ProductSpecications
Model IGS-501T IGS-801T
HardwareSpecications
10/100/1000BASE-T
Ports 5 8
Dimensions
(W x D x H) 135 x 87 x 32 mm
Weight 498g 461g
Power Requirements
12~48V DC, redundant power with polarity
reverse protection function, 24V AC power
support
Power Consumption/
Dissipation 5.28 watts/18BTU 6.72 watts/23BTU
Installation DIN rail kit and wall-mount ear
SwitchSpecications
Switch Processing
Scheme Store-and-Forward
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet FSD-1604 Manual de usuario
Planet
Planet FSD-1600 Manual de usuario
Planet
Planet GSW-1402S Manual de usuario
Planet
Planet GSD-Series Manual de usuario
Planet
Planet WGSW-2840 Manual de usuario
Planet
Planet IGS-5225 Series Manual de usuario
Planet
Planet FNSW-1601 Manual de usuario
Planet
Planet GSW-2416SF Manual de usuario
Planet
Planet FGSW-2402S Manual de usuario
Planet
Planet XGS3-24042 Manual de usuario
Planet
Planet IGS-4215 Series Manual de usuario
Planet
Planet GS-5220-8P2T2S Manual de usuario
Planet
Planet IAP-2000PE Manual de usuario
Planet
Planet IGSW-2840 Manual de usuario
Planet
Planet NOVASwitch GSW-1200S Manual de usuario
Planet
Planet GSW-1601 Manual de usuario
Planet
Planet WGS-5225-8UP2SV Manual de usuario
Planet
Planet IGSW-24040T Manual de usuario
Planet
Planet IFGS-1022HPT Manual de usuario
Planet
Planet VC-810S Manual de usuario
