Parker U Series Especificaciones técnicas
Maintenance
Instructions
MI-104 Revision -
Parker Hannifin Corporation
Instrumentation Valve Division
Jacksonville, Alabama
1
U Series Needle Valve
Table I: Maximum Working Pressure and Temperature
Valve Packing Maximum Pressure and Temperaure Maximum Temperature and Pressure
Grafoil ® 6000 psig at 70 °F 1545 psig at 1200 °F
41.4 MPa at 21 °C 10.7 MPa at 649 °C
PTFE 6000 psig at 70 °F 4280 psig at 450 °F
41.4 MPa at 21 °C 29.5 MPa at 204 °C
Al ays consult your authorized Parker representative if questions arise. The arro on the Valve Body indicates the
normal direction of flo .
Table II: Packing Nut
Hex Wrench Sizes and Tightening Re uirements
Valve Size Hex Wrench Size PTFE Stem Packing Graf il ® Stem Packing
U6 3/4 inch 125 in-lbs 10.4 ft-lbs
(14.1 N-m) (37.3 N-m)
U12 15/16 inch 150 in-lbs 33.3 ft-lbs
(16.8 N-m) (44.8 N-m)
U16 1-1/8 inch 50 ft-lbs 50 ft-lbs
(67.8 N-m) (67.8 N-m)
Parker Hannifin Corporation
Instrumentation Valve Division
Jacksonville, Alabama
MI-104
Figure 1: U Series Needle Valve
Cross Sectional Vie
Table III: Lock Nut
Hex Wrench Sizes and Tightening Re uirements
Valve Size Hex Wrench Size T rque Requirement
U6 model 3/4 inch 125 in-lbs (14.1 N-m)
U12 model 15/16 inch 150 in-lbs (16.8 N-m)
U16 model 1 1/4 inch 150 in-lbs (16.8 N-m)
Table IV: Bonnet Nut
Hex Wrench Sizes and Tightening Re uirements
Valve Size Hex Wrench T rque Requirements
U6 model 15/16 inch 65 ft-lbs. (88 N-m)
U12 model 1-1/4 inch 75 ft-lbs. (101 N-m)
U16 model 1-1/2 inch 100 ft-lbs. (135 N-m)
PANEL MOUNTED VALVES
The panel must have a through-hole diameter of correct diameter. The maximum panel thickness is 1/4 inch (6.4
mm).
U6 model 41/64 inch (16.2 mm)
U12 model 53/64 inch (21.0 mm)
U16 model 1-1/64 inch (25.8 mm)
1.Remove the Handle by unthreading the Set Scre in the side of the Handle ith the follo ing size allen rench:
U6 model 3/32 inch
U12 model 3/32 inch
U16 model 1/8 inch
2.Grip the Packing Nut ith a rench as listed in Table II. With another rench (as listed in Table III), loosen the
Lock Nut.
3.Remove both the Packing Nut and the Lock Nut by unthreading until completely removed.
4.Insert the Valve through the hole in the panel and assemble the Panel Nut onto the Bonnet finger-tight. For assembly,
grip the large Bonnet Nut ith a hex rench as listed in Table IV and tighten the Panel Nut securely.
CAUTION: Do not grip the Valve Body or loosen the Bonnet Nut.
5.Thread the Lock Nut onto the Bonnet. Thread the Packing Nut onto the Bonnet and tighten in accordance ith
Table II.
6.Tighten the Lock Nut against the Packing Nut in accordance ith Table III.
7.Re-install the Handle ith the Set Scre onto the Stem.
2
Parker Hannifin Corporation
Instrumentation Valve Division
Jacksonville, Alabama
MI-104
3
DISASSEMBLY
MAKE CERTAIN THE SYSTEM IN WHICH THE VALVE IS INSTALLED IS DRAINED AND/OR EXHAUSTED OF ALL
PRESSURES BEFORE VALVE DISASSEMBLE OR REMOVAL OCCURS.
1.Verify that the Union Bonnet Valve Maintenance Kit being used is appropriate for the Valves size, handle, stem
packing configuration and service requirements. Al ays contact your authorized Parker representative if any ques-
tions arise.
2.Remove the Handle by unthreading the Set Scre in the side of the Handle ith the follo ing size allen rench.
U6 model 3/32 inch
U12 model 3/32 inch
U16 model 1/8 inch
3.Loosen the Locknut, located directly under the Packing Nut, by turning clock ise ith the follo ing size hex
rench:
U6 model 3/4 inch
U12 model 15/16 inch
U16 model 1-1/4 inch
4.Remove and save the Packing Nut, located directly under the Handle, by turning counter-clock ise ith the follo -
ing size hex rench:
U6 model 3/4 inch
U12 model 15/16 inch
U16 model 1-1/8 inch
5.Remove and save the Locknut from the Bonnet
6.Remove and discard the Lube Seal from ithin the Packing Nut.
7.If applicable, remove the Valve Body from its panel mounting hole by turning the Panel Nut counter-clock ise and
removing it from the Bonnet.
8. Remove and save the Bonnet Nut, located directly above the Body, by turning counter-clock ise ith the follo ing
size hex rench:
U6 model 15/16 inch
U12 model 1-1/4 inch
U16 model 1-1/2 inch
9. Remove the Bonnet/Stem Assembly from the Valve Body.
10. Press the Stem UP to disengage the Stem Guide hex from the Bonnet.
11. While carefully securing the Valve Stem, remove the Stem Guide from the Bonnet using the follo ing size hex
rench:
U6 model 3/8 inch
U12 model 9/16 inch
U16 model 11/16 inch
12. Slide the Valve Stem from the Bonnet by applying a minimal amount of force (i.e. hand pressure) on the Handle
end of the Valve Stem and pushing to ards the seat end.
13. Remove the Packing Washers and the Packing from ithin the Bonnet. The Upper Packing Washer should fall out
easily. The Packing must be pushed out ith a thin probe or ire. After this is removed the lo er Packing Washer
should also fall out.
NOTE: If the valve is Grafoil® packed make certain the entire packing is removed since it may break-up during removal.
14. Discard the appropriate components from the valve consistent ith the ne components ithin the Valve Kit.
Additi nal Step (U16 nly)
15. Using a pick or thin flat headed scre driver remove the metal o-ring from ithin the Valve Body. Insure care not
to damage the o-ring groove.
Parker Hannifin Corporation
Instrumentation Valve Division
Jacksonville, Alabama
MI-104
4
REASSEMBLY
Make certain all parts are free f dirt r ther c ntaminati n bef re starting reassembly f the Valve.
1.Clamp the Body in a vise.
2.U16 nly: Install the Metal O-Ring into the o-ring groove in the Valve Body
3.Insert the three packing components into the Bonnet in the follo ing order ith the first item being placed at the
bottom of the Bonnet:
Packing Washer
Stem Packing
Packing Washer
4.Insert the Stem Guide into the Bonnet, use it to push the packing components to the bottom of the Bonnet. Insert
the Stem Guide hex into the hex-shaped slot at the top of the Bonnet.
5.Apply a liberal amount of lubricant, as consistent ith the Valves service requirements, to the Stem Sub-Assembly
threads. Al ays contact your authorized Parker representative is questions arise.
NOTE: Every thread must be covered ith lubricant.
6.Refer to Figures 2 and 3. Carefully install the Stem Sub-Assembly into the Bonnet from the lo er end until hand-
tight.
7.Apply a liberal amount of lubricant, as consistent ith the Valves service requirements, to the Body threads, as ell
as to the surface area here the Bonnet fits up against the interior of the Bonnet Nut. Al ays contact your
authorized Parker representative if questions arise.
8.Place the hand-tight Bonnet and Stem Sub-Assembly from Step 6 into the Body. Torque the Bonnet Nut onto the
Body using the hex rench size and torque specified in Table IV.
9.This Step only applies to Valves ith an optional Panel Nut, else proceed to Step 10.
Insert the Body into its panel mounting hole. Thread the Panel Nut clock ise onto the Bonnet until the Valve is
secure in the mounting panel.
10. Place the Lube Seal over the Stem to the top of the Stem Guide.
11. Apply a small amount of lubricant, as consistent ith the Valves service requirements, to the Bonnet upper threads
and the top of the Stem Guide.
NOTE: A minimum of the upper four (4) Bonnet threads must be covered ith lubricant !
12. Place the Locknut on the Bonnet and thread it do n near the Panel Nut. Place the Packing Nut over the Bonnet.
Tighten in accordance ith Table II.
13. Tighten the Locknut against the Packing Nut. Tighten in accordance ith Table III.
14. Re-install the Handle ith the Set Scre onto the Stem.
15. Install the Handle on the Stem Sub-Assembly. Secure the Handle ith the Set Scre , and tighten the Set Scre
to 15 In-lbs torque, using a 3/32 inch allen rench. Verify the Handle is tightly fastened.
16. Turn the Bar Handle through at least one (1) Open and Close cycle to verify proper operation of the Stems
threads.
17. Reject and rebuild any Union Bonnet Valve exhibiting rough or irregular Stem operation. Al ays contact your
authorized Parker representative if questions arise.
Parker Hannifin Corporation
Instrumentation Valve Division
Jacksonville, Alabama
MI-104
5
Figure 3: Size 16 Union Bonnet Valve Exploded View
Figure 2: Size 6 & Size 12 Union Bonnet Valve Exploded View
MI-104
Parker Hannifin Corporation
Instrumentation Valve Division
Jacksonville, Alabama
6
VALVE CONNECTOR MAKE-UP INSTRUCTIONS
MALE AND FEMALE PIPE PORTS
Wrench flats are provided on the Valve Body. It is recommended a smooth- jawed wrench or vise be used to grip the Valve Body.
1. On the male threaded part of the connection apply a high quality pipe joint compound or PTFE tape made for this purpose. When PTFE tape is
used it is recommended two full turns of tape be applied. PTFE tape should not be overhanging or covering the first thread
2. Engage the Valve and the other component part together until hand-tight.
3. With a proper wrench holding both the Valve and the component part continue to tighten to achieve a leak-tight joint.
ULTRASEAL CONNECTIONS
1. Insert the proper O-Ring into the UltraSeal fittings O-Ring groove. Position the UltraSeal gland sealing face against the O-Ring and then advance
the Nut to a finger-tight position.
2. A positive seal is obtained by advancing the Nut no less than 1/4 turn from the finger-tight position. Proper UltraSeal make-up is achieved when
a sharp rise in required application torque occurs which indicates proper seal face contact and O-Ring seal compression into the UltraSeal
groove.
VACUSEAL CONNECTIONS
1. A positive seal is obtained by advancing the Nut 1/8 turn from the finger-tight position.
2. A new gasket should be installed upon each fitting re-make to insure system pressure integrity.
TUBE FITTING CONNECTIONS
1. Insert the tube into the Valve port until the tube bottoms out in the Valve Body. Care should be exercised to insure the tube is properly aligned with
the Valve Body and port.
2. Normal make-up for US Customary port sizes 1 thru 3 (1/16 thru 3/16 inch) and SI port sizes 2 thru 4 (2 thru 4 mm) is 3/4 turn from finger tight.
Normal make-up for US Customary port sizes 4 thru 16 (1/4 thru 1 inch) and SI port sizes 5 thru 25 (5 thru 25 mm) is 1 1/4 turn from finger tight.
For larger port sizes consult Parker Ferrule Presetting Tool Instructions.
PLEASE FOLLOW THE ABOVE DIRECTIONS FOR COUNTING THE NUMBER OF TURNS FOR PROPER FITTING MAKE-UP. DO
NOT MAKE-UP TUBE FITTINGS BY TORQUE OR FEEL. VARIABLES SUCH AS TUBING AND FITTING TOLERANCES, TUBE
WALL THICKNESS, AND THE LUBRICITY OF NUT LUBRICANTS CAN RESULT IN AN IMPROPERLY ASSEMBLED TUBE FITTING
CONNECTION.
A -Two ferrule A-LOK ®
compression port
M -ANSI/ASME B1.2 .1
External pipe threads
Z -Single ferrule CPITM
compression port
Q -UltraSeal face
seal port
F -ANSI/ASME B1.2 .1
Internal pipe threads
V -VacuSeal face
seal port
Parker Hannifin Corporation
Instrumentation Valve Division
2651 Alabama Highway 21 North
Jacksonville AL 36265-9681
USA
Phone: (256) 435-2130
Fax: (256) 435-7718
www.parker.com/IVD
MI-1 4 Revision -
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors
provide product and/or system options for further investigation by users having technical expertise. It is important that
you analyze all aspects of your application and revie the information concerning the product or system in the current
product catalog. Due to the variety of operating conditions and applications for these products or systems, the user,
through its o n analysis and testing, is solely responsible for making the final selection of the products and systems
and assuring that all performance, safety and arning requirements of the application are met.
The products described herein, including ithout limitation, product features, specifications, designs, availability and
pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time ithout notice.
ALL PARKER VALVES MUST PASS A RIGID OPERATIONAL AND LEAKAGE TEST BEFORE LEAVING THE FAC-
TORY. IT IS RECOMMENDED AFTER ANY REASSEMBLY, THE VALVE SHOULD BE TESTED BY THE USER FOR
OPERATION AND LEAKAGE. IF THESE INSTRUCTIONS ARE NOT FULLY COMPLIED WITH, THE REPAIRED
PRODUCT MAY FAIL AND CAUSE DAMAGE TO PROPERTY OR INJURY TO PERSONS. PARKER HANNIFIN
CANNOT ASSUME RESPONSIBILITY FOR PERFORMANCE OF A CUSTOMER SERVICED VALVE.
Este manual sirve para los siguientes modelos
10
Otros manuales de Unidad de control de Parker
Parker
Parker R4V Series Diagrama de cableado
Parker
Parker DINCon II Instrucciones de montaje
Parker
Parker Sporlan LAC-4 Nota de publicación
Parker
Parker PACHC Series Manual de usuario
Parker
Parker IOTA ONE Series Manual de usuario
Parker
Parker ASV5000 Series Manual de usuario
Parker
Parker PHD Series Manual de usuario
Parker
Parker 930 Series Guía
Parker
Parker D31FBxEE Series Manual de usuario
Parker
Parker IQAN-XC21 Manual de usuario
Parker
Parker Hi-Pro Manifold Manual de usuario
Parker
Parker D1FV EE Series Manual de usuario
Parker
Parker D1FH series Manual de usuario
Parker
Parker Series DFplus Manual de usuario
Parker
Parker EP Series Pro-Bloc Manual de usuario
Parker
Parker SciLog DINCon Instrucciones de montaje
Parker
Parker U131B01 Instrucciones de montaje
Parker
Parker AC30V Series Manual de usuario
Parker
Parker S7A Manual de servicio
Parker
Parker VA01 Series Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
