Parker TPQ Series Manual de usuario

Proportional

Throttle Valve

Operation Manual

Series TPQ

Design ≥ 30

Parker Hanniﬁn

Manufacturing Germany GmbH & Co. KG

Hydraulic Controls Division Europe

Gutenbergstr. 38

41564 Kaarst, Germany

Tel.: (+49) 181 99 44 43 0

E-mail: infohcd@parker.com

Bulletin HY11-5715-653/UK

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

Note

This document and other information from Parker Hanniﬁn GmbH,

its subsidiaries, sales ofﬁces and authorized distributors provide

product or system options for further investigation by users having

technical expertise. Before you select or use any product or system

it is important that you analyse all aspects of your application and

review the information concerning the product or system in the

current product catalogue.Due to the variety of operating conditions

and applications for these products or systems, the user, through

his own analysis and testing, is solely responsible for making the

ﬁnal selection of the products and systems and assuring that all

performance and safety requirements of the application are met.

The products are subject to change by Parker Hanniﬁn GmbH at

any time without notice.

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

Content Page

1. Introduction 4

Characteristics of Valve Driver 4

Order Code 4

Block Diagram of Integral Electronics 5

Technical Data 6

2. Safety Instructions 7

Symbols 7

Marking, Name Plates 7

Work at the Valve 7

3. Important Details 7

Intended Usage 7

Common Instructions 7

Liability 7

Storage 7

4. Mounting / Installation 8

Scope of Supply 8

Mounting 8

Mounting Bolts 8

Operation Limits 8

Pressure Fluids 8

Electrical Connection 9

Electrical Interfacing 10

5. Operation Instructions 14

Solenoid Current Monitoring 14

Air Bleeding of Hydraulic System 14

Filter 14

Flushing 14

6. Maintenance 15

7. Trouble Shooting 15

8. Accessories / Spare Parts 16

Accessories 16

Spare Parts 16

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

1. Introduction

Parker TPQ proportional throttle valves have an

integral electronic and requires only one sole elec-

trical common for the control system. Different ﬂow

sizes are available to achieve an optimal adaption

for different applications.

Characteristics of Valve Driver

The described integral electronic driver combines

all necessary functions for the optimal operation of

the valve.Thanks to its excellent dynamic the valve

is usable within closed loop control applications.

The most important features are:

Ordering Code

Proportional

throttle valve

with LVDT Pilot oil

(supply external,

drain external)

Seal

Design

series

(not required

for ordering)

Linear

spool

Nominal

size

Standard

electronics

Input

signal

TPQ W H 2 5 0

Parker Slip-

in cartridge

Closed loop,

VCD®performance,

integrated

electronics

Code Seal

N NBR

V FPM

H for HFC ﬂuids

Flow

Spool type

Code Signal range

B0...±10 V

S 4...+20 mA

• high dynamic actuator principle with special

designed electronic driver

• closedloopcontrolledspoolposition

• constantcurrentactuatorcontrolwithovercurrent

shutoff

• excellentpropertiesforresponsesensitivityand

temperature drift

• differentialinput stage withvariouscommand

signal options

• diagnosticoutputforspoolstroke

• standardcentralconnection

• compatible to the relevant European EMC-

standards

Code Nominal size

025 NG25

032 NG32

040 NG40

050 NG50

063 NG63

080 NG80

Position overlap

Code

Spool type Fail

save

Input signal

- 0 +

P →A

A →T

Please order connector separately

Angle female connector must be used for NG25 to NG50.

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

Blockdiagram of integrated electronics

Supply

voltage

Command

0...±10V

4...20mA

0...±10V

22...30V=

Zero position

PID

Diagnostic

spool stroke

Enable

+5...30V

Function symbol

Fail safe position spool type P

1) NG25 and NG32 without accu port XX

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

Technical data

General

Design Proportional throttle valve, slip-in cartridge

Nominal size DIN NG25 NG32 NG40 NG50 NG63 NG80

Mounting position unrestricted

Ambient temperature [°C] -20...+50

MTTFDvalue 1) [years] 75

Weight [kg] 11 13 15 26 52 105

Vibration resistance [g] 10 sinus 5...2000 Hz acc. IEC 68-2-6

30 random noise 20...2000 Hz acc. IEC 68-2-36

15 shock acc. IEC 68-2-27

Hydraulic

Max. operating pressure [bar] Ports A, P, T, X up to 350, XX 2) observe permissible pressure rating; port

Y: max. 35

Fluid Hydraulic oil according to DIN 51524...51525

Fluid temperature [°C] -20 ... +60

Viscosity recommended [cSt]/

permitted [cSt]/

[mm²/s]

30 ... 80

20 ... 380

Filtration ISO 4406 (1999); 18/16/13

Nominal ﬂow at ∆p = 5 bar [l/min] 200 320 550 800 1450 2700

Recommended max. ﬂow [l/min] 500 1000 1600 2250 3500 6500

Nominal overlap [%] < 1.5

Flow direction A to T or P to A

Pilot pressue [bar] must be as high as system pressure

Pilot oil supply external via X

drain external via Y

Leakage in pilot valve at 100 bar [ml/min] < 400

Leakage in main stage at 100 bar [l/min] NG32 to 63 <2.5; NG80 <4.0

Pilot valve size NG06 NG10

Max. pilot ﬂow at 140 bar pilot press. [l/min] 25 25 25 25 50 60

Static/dynamic

(for optimal dynamics see installation recommendation)

Step response at pilot press. >140 bar [ms] 7 11 11 18 19 20

Frequency response at pilot press. >140 bar

Amplitude -3 dB; ±5 %

[Hz] 210 105 70 45 35 30

Phase -90°;

±5

[Hz] 170 125 110 95 75 70

Hysteresis [%] < 0.1

Sensitivity [%] < 0.05

Temperature drift of center position [%/K] < 0.025

Electrical

Duty ratio [%] 100

Protection class

IP65 in accordance with EN 60529 (with correctly mounted plug-in connector)

Supply voltage / ripple [V] 22...30, ripple < 5 % eff., surge free

Current consumption max. [A] 3.5

Pre-fusing [A] 4.0 A medium lag

Input signal voltage [V] +10...0...-10, ripple < 0.01 % eff., surge free

Impedance [kOhm] 100

Input Capacitance typ. [nF] 1

Current [mA] 4...12...20, ripple < 0.01 % eff., surge free

< 3.6 mA = enable off, > 3.8 mA = enable on acc. NAMUR NE43

Impedance [Ohm] 250

Differential input max. [V] 30 for terminal D and E against PE (terminal G),

[V] 11 for terminal D and E against 0V (terminal B)

Diagnostic signal [V] 0...±10 rated max. 5 mA

Enable signal [V] 5...30, Ri = 9 kOhm

EMC EN 61000-6-2, EN 61000-6-4

Electrical connection 6 + PE acc. EN 175201-804

Wiring min. [mm2] 7x1.0 (AWG16) overall braid shield

Wiring length [m] 50

1) If valves with onboard electronics are used in safety-related parts of control systems, in case the safety function is requested, the valve

electronics voltage supply is to be switched off by a suitable switching element with sufﬁcient reliability.

2) Accu port XX: Please contact Parker for installation recommendation.

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

Common Instructions

We reserve the right for technical modiﬁcations of

the described product. Illustrations and drawings

within this manual are simpliﬁed representations.

Due to further development, improvement and

modiﬁcation of the product the illustrations might

not match precisely with the described valve. The

technical speciﬁcations and dimensions are not

binding.No claim may resulting out of it. Copyrights

are reserved.

Liability

The manufacturer does not assume liability for

damage due to the following failures:

• incorrect mounting / installation

• improper handling

• lack of maintenance

• operation outside the speciﬁcations

Do not disassemble the valve! In case of

suspicion for a defect please return the valve

to the factory.

Storage

In case of temporary storage the valve must be

protected against contamination, atmospheric ex-

posure and mechanical damages. Each valve has

been factory tested with hydraulic oil, resulting in

protection of the core parts against corrosion. Yet

this protection is only ensured under the following

conditions:

2. Safety Instructions

Please read the operation manual before instal-

lation, startup, service, repair or stocking! Paying

no attention may result in damaging the valve or

incorporated system parts.

Symbols

This manual uses symbols which have to be follo-

wed accordingly:

Instructions with regard to the warranty

Instructions with regard to possible

damaging of the valve or linked system

components

Helpful additional instructions

Marking, Name Plates

Instructions applied on the valve, i.e. wiring dia-

grams and name plates, must be observed and

maintained legibly.

Work at the Valve

Workings in the area of installation, commissioning,

maintenance and repair of the valve may only be

allowed by qualiﬁed personnel.This means persons

which have, because of education, experience

and instruction, sufﬁcient knowledge on relevant

directives and approved technical rules.

3. Important Details

Intended Usage

This operation manual is valid for proportional

throttle valves TPQ series. Any different or be-

yond it usage is deemed to be as not intended.

The manufacturer is not liable for warranty claims

resulting from this.

Outdoor storage or within sea and tropical

climate will lead to corrosion and might disable

the valve!

Storage

period Storage requirements

12 months constant humidity < 60 % as well

as constant temperature < 25 °C

6 months varying humidity as well as va-

rying temperature < 35 °C

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

For detailed information concerning pressure

ﬂuids note VDMA-document 24317 as well

as DIN 51524 & 51502.

• Check the proper position of the valve ports

and the O-rings.

• Mounting bolts: use property class 12.9, DIN

912

Insufﬁcient condition of the valve mounting

surface migth create malfunction!

Incorrect mounting resp. bolt torque may

result in abrupt leakage of hydraulic ﬂuid on

the valve ports.

Y-port has always to be tied directly and

separately to tank!

Operation Limits

The valve may be operated within the determined

limits only. Please refer to the “technical data“

section as well as to the “characteristic curves“ in

the catalog.

Follow the environmental conditions! Unallo-

wable temperatures, shock load, aggresive

chemicals exposure, radiation exposure,

illegal electromagnetic emissions may result

in operating trouble and may lead to failure!

Follow the operating limits listed in the “spe-

ciﬁcations“ table!

4. Mounting / Installation

Scope of Supply

Please check immediately after receiving the valve,

if the content is matching with the speciﬁed scope

of supply. The delivery includes:

• valve

• operation manual

Please check the delivery immediately after

receiving the shipment for apparent damages

due to shipping. Report shipment losses at

once to the carrier, the insurance company

and the supplier!

Mounting

• Compare valve type (located on the name plate)

with part list resp. circuit diagram.

• The valve may be mounted ﬁx or movable in

any direction.

• Verify the mounting surface for the valve. Une-

veness of 0.01 mm/100 mm, surface ﬁnish of

6.3 µm are tolerable values.

Keep clean valve mounting surface and work

environment!

• Remove protection plate from the valve mounting

surface

Mineral oil for use without restriction

HFA oil in water - emulsion consultation necessary

HFB water in oil - emulsion consultation necessary

HFC aqueous dilutions (glycol) consultation necessary

HFD waterfree ﬂuids (phosphor-ester) consultation necessary

Available Bolt Kits

Pressure Fluids

The following rules applies for the operation with

various pressure ﬂuids:

The above information serves for orientation

and does not substitute user tests among the

particular operating conditions.Particularly no

liabiliy for media compatibility may be derived

out of it.

Special gaskets may be available depending

on the utilized ﬂuid.

In case of insecurity please consult the facory.

Size Ordering no. Dimensions Torque

TPQ025 BK504 4 pcs. M12x100 108 Nm

TPQ032 BK529 4 pcs. M16x100 264 Nm

TPQ040 BK513 4 pcs. M20x110 517 Nm

TPQ050 BK513 4 pcs. M20x110 517 Nm

TPQ063 BK518 4 pcs. M30x160 1775 Nm

TPQ080 BK530 8 pcs. M24x160 517 Nm

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

The connecting cable has to comply to the follow-

ing speciﬁcation:

Cable type control cable, ﬂexible,

7 conductors, overall braid

shield

Cross section min. AWG16

Outer dimension 8...12 mm

Cable length max. 50 m

For cable lengths > 50 m consult factory.

The connection cable is coupled to the female

connector by solder joints.

Skinning lengths for the connecting cable:

Electrical Connection

The electrical connection of the valve takes place

by one common cable, which is coupled to the

integrated electronic driver by a central connector

assembly.

The connection requires a 6 + PE female connector

EN 175201-804.

Female connector (ordering no. 5004072)

Do not disconnect cable socket under tension!

7/8-20

UNEF-2B

Ø28.6

max. 67

PG13.5

A female connector with metal housing is

required! Plastic made models may create

function problems due to insufﬁcient EMC-

characteristics.

Angled female connector (ordering no. 5005160)

TPQ_30 5715-653 UK.indd RH 06.10.14

Proportional Throttle Valve

Series TPQ

Operation Manual

Parker Hanniﬁn Corporation

Hydraulics Group

Electrical Interfacing

Supply Voltage:

The supply voltage for the valve has to cover the

range of 22...30 V. The residual ripple may not

exceed 5% eff.

The applied power supply must comply to

the relevant regulations (DIN EN 61558)

and must carry a CE-mark. The operating

voltage for the valve must be free of inductive

surges.Do not exceed the max. value of 30V!

Non-observance of this rule may result in

permanent damaging of the valve.

The increased inrush current of the valve

should be considered when selecting the

power supply. A stabilized power supply with

overcurrent limiting feature should not be

used.Due to the inrush current of the valve the

current limit circuit may respond prematurely

and create problems during energizing of the

supply voltage.

The operation of the valve is blocked if the

supply voltage polarity is interchanged.

Each valve requires a separate pre-fuse

of 4 Amp time lag. Non-observance of this

instruction may create irreparable damage

of valve resp. incorporated system parts.

The shielding has to be assembled according the

outline below:

The backshell nut of the cable gland has to be

tighten with a suitable tool.The target value for the

tightening torque is 4 Nm. Tighten the cap nut with

a torque of approx.5 Nm after attaching the female

connector on the socket outlet.

Incomplete tightening of backshell nut resp.

cap nut may result in automatic release of

the connection as well as degradation of the

water tightness.

Follow the“instructions for use“ for installation

of female connectors made by other kind of

brands!

The cable connection to the female connector

has to take place by qualiﬁed personnel! A

short between individual conductors resp. to

the connector housing , bad soldering as well

as improper shield connection may result in

malfunction and breakdown of the valve.

The mounting surface of the valve has to be

carefully tied to the earth grounded machine

frame. The earth ground wire from the valve

connecting cable as well as the cable shield

have to be tied to the protective earth terminal

within the control unit. It is necessary to use

a low ohmic potential connection between

control unit and machine frame to prevent

earth loops (cross section AWG 6).

Otros manuales para TPQ Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Parker

Parker

Parker PSST8M23A Instrucciones de instalación y mantenimiento

Parker

Parker 60VM4071 Manual de usuario

Parker

Parker PK2 Manual de usuario

Parker

Parker TPQ Series Manual de usuario

Parker

Parker EBV-PR Series Guía del usuario

Parker

Parker C6 Series Instrucciones de instalación y mantenimiento

Parker

Parker EP Series Pro-Bloc Manual de usuario

Parker

Parker 221 Series Manual de usuario

Parker

Parker RL Series Especificaciones técnicas

Parker

Parker 930 Series Guía

Parker

Parker 20K Manual de usuario

Parker

Parker S4A-DN Instrucciones de funcionamiento e instalación

Parker

Parker Series DFplus Manual de usuario

Parker

Parker TFP Series Manual de usuario

Parker

Parker LINKnet TechBox Series Manual de usuario

Parker

Parker Series DFplus Manual de usuario

Parker

Parker 20K Manual de usuario

Parker

Parker S6N-DN Manual de usuario

Parker

Parker PA Series Instrucciones de montaje

Parker

Parker 810 Series Instrucciones de montaje

Parker

Parker PA Series Instrucciones de montaje

Parker

Parker R4V Series Diagrama de cableado

Parker

Parker U Series Especificaciones técnicas

Parker

Parker PACHC Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario