Parker C10 Manual de usuario

The green/yellow (Gnd) wire is for safety

purposes. The shield connection to the motor

case is for EMI purposes (the C10 and C10H cable

kits provides hardware for the shield connection).

Phase A

Windings

Phase B

Windings

28 74

Wire #1

Wire #3

Gnd (Grn/Ylw)

Wire #2

Wire #4

127

Gnd1324Motor Terminal Number/Wire Number:

Refer to your product’s

user guide for

connection instructions.

End Cover RemovedSchematic View

Phase A

Windings

Phase B

Windings

28 74

Wire #1

Wire #3

Gnd (Grn/Ylw)

Wire #2

Wire #4

The green/yellow (Gnd) wire is for safety

purposes. The shield connection to the motor

case is for EMI purposes (the C10 and C10H cable

kits provides hardware for the shield connection).

127

Gnd1324Motor Terminal Number/Wire Number:

Refer to your product’s

user guide for

connection instructions.

Exposed Braid

Outter Jacket Inner Jacket

Drive End Motor End

Rubber Moisture Seal

EMI Shield

Top Half of Casing

Motor Cable

(10-foot)

Gland

Brass Contact Sleeve

Base Half of Casing

Thread

Converter

R-Clamp

Drive End

To Motor

Remove outer jacket only.

Do not cut braid.

C10 & C10H Cable Assembly

(for R & T Series Motors)

Step 6

You are now ready to wire your motor for series or parallel.

Series Wiring

END OF ASSEMBLY INSTRUCTIONS

p/n 88-016411-01 B page 1

page 4 p/n 88-016411-01 B

CAUTION

At no time during this procedure should the motor cable be allowed to twist within

the gland assembly. This can damage the cable and greatly reduce its life.

Step 1

Inventory, what you should have:

• Thread converter

• Gland assembly (5 pieces)

• Motor cable, 10 ft (3 m)

• R-Clamp with 6-32 x 1/2-inch screw

Required assembly tools and hardware:

• Phillips screwdriver #2

• Wire strippers

• Standard slotted screwdriver, approximately 0.25 in (6 mm)

• Crimp-on ring terminals (C10 cable uses 18AWG, 0.75 mm2wire;

C10H cable uses 14 AWG, 2.50 mm2wire) – see step 6:

9 required for series wiring, 13 required for parallel wiring

• 18AWG (0.75 mm2) wire jumpers (use 18 AWG for both C10 & C10H),

4 inches (100 mm) long – see step 6:

2 required for series wiring, 4 required for parallel wiring

• Crimp tool

• Open-end 15/16-inch wrench

Parallel Wiring

Step 7

Connect the motor cable to the drive or drive/controller product. Avoid looping

the cable. Keep the motor cable away from I/O cables carrying control signals.

Refer to your product’s user guide for instructions.

R-Clamp and Screw

Base Half of Casing

Thread Converter

Step 2

a. Remove and discard the motor’s plastic thread

insert (CCW rotation).

b. Remove endbell cover plate from the rear of the

motor.

c. Insert the thread

converter into the

motor rear endbell, and

tighten. The NPT

thread is designed for

compression fit into

the motor body and

therefore will not

bottom out.

d. Insert the base half of

the outer casing into

the thread converter

and tighten securely.

Step 3

a. From the motor end of the cable, first slide on the dome casing half, then the

EMI shield, and finally the rubber moisture seal. The EMI shield is installed

blunt end first. The tapered end of the EMI shield fits over the tapered end of

the rubber moisture seal.

b. This step is critical and if not done properly will impair the EMC perfor-

mance of the system:

With a finger tip, flare the braid away from the inner jacket of the cable (all the

way around). This will allow the braid to relax, and eases insertion of the brass

sleeve.

c. Carefully slide the brass sleeve as far under the exposed braid as possible. The

sleeve must not cause the braid to bunch up or slide up under the outer jacket.

The sleeve flange should butt up against the inner jacket of the cable.

Slide over brass contact sleeve

Step 4

a. Slide the rubber moisture seal up to the flange of the brass sleeve.

b. Slide the EMI shield onto the rubber moisture seal.

c. Slide the dome half of the outer casing over the EMI shield.

Rubber Moisture Seal Brass Contact Sleeve

Dome Half

of Casing

Drive End Motor End

EMI Shield Flare

Braid

Inner Jacket

Slide sleeve

under braid

Step 5

Insert the assembly into the prepared motor and

screw the dome half to the base half of the outer

casing until snug. Do not twist the cable.

p/n 88-016411-01 B page 3

page 2 p/n 88-016411-01 B

Este manual sirve para los siguientes modelos

Otros manuales de Unidad de control de Parker

Parker

Parker 89-00B Guía

Parker

Parker D31FBxEE Series Manual de usuario

Parker

Parker TFP Series Manual de usuario

Parker

Parker 60VM4071 Manual de usuario

Parker

Parker PQDXXA-Z10 Manual de instalación y operación

Parker

Parker PHD Series Manual de usuario

Parker

Parker P33 Guía de configuración rápida

Parker

Parker SC Series Manual de referencia

Parker

Parker CK-1 Guía

Parker

Parker TPQ Series Manual de usuario

Parker

Parker C2 Series Instrucciones de instalación y mantenimiento

Parker

Parker Vansco VMM1210 Manual de usuario

Parker

Parker 20K Manual de usuario

Parker

Parker U131B01 Instrucciones de montaje

Parker

Parker D*1VW*EE Series Manual de usuario

Parker

Parker 221 Series Manual de usuario

Parker

Parker D1FB EE Series Manual de usuario

Parker

Parker BAM20 Manual de usuario

Parker

Parker 810 Series Instrucciones de montaje

Parker

Parker S5A Guía

Parker

Parker PID00A-40X Series Manual de usuario

Parker

Parker CK-6D Guía

Parker

Parker Autoclave Engineers 10V Series Manual de usuario

Parker

Parker S7A Manual de servicio

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario