Panasonic KX-TG5671S Manual de usuario

rights reserved. Unauthorized copying and

distribution is a violation of law.

KX-TG5671S

KX-TG5672B

KX-TG5673B

KX-TGA560S

KX-TGA560B

5.8 GHz Digital Cordless Answering

System

Silver Version

Black Version

(for U.S.A.)

Telephone Equipment

ORDER NO. KM40601971CE

F12

1 ABOUT LEAD FREE SOLDER (PbF: Pb free) 4

1.1. Suggested PbF Solder 4

1.2. How to Recognize that Pb Free Solder is Used 5

2 FOR SERVICE TECHNICIANS 6

3 CAUTION 6

4 OPERATING INSTRUCTIONS 7

4.1. Battery 7

4.2. Location of Controls 9

4.3. Displays 11

4.4. Settings 13

4.5. Troubleshooting 18

5 DISASSEMBLY INSTRUCTIONS 22

5.1. Base Unit 22

5.2. Handset 23

5.3. Charger Unit 24

6 HOW TO REPLACE THE HANDSET LCD 25

7 TROUBLESHOOTING GUIDE 26

7.1. Check Power 27

7.2. Error Message Table 27

7.3. Check Record 28

7.4. Check Playback 29

7.5. Check Sp-phone Transmission 29

7.6. Check Sp-phone Reception 30

7.7. Check Battery Charge 30

7.8. Check Link 31

7.9. Check the RF part 32

7.10. Check Handset Transmission 39

7.11. Check Handset Reception 39

7.12. Check Caller ID 39

8 ADJUSTMENT AND TEST MODE 40

8.1. Test Mode Flow Chart for Base Unit 40

8.2. Test Mode Flow Chart for Handset 44

8.3. X501 (Base Unit), X201 (Handset) Check 48

8.4. Adjust Battery Low Detector Voltage (Handset) 48

8.5. Base Unit Reference Drawing 49

8.6. Handset Reference Drawing 50

8.7. Frequency Table 51

8.8. How to Clear User Setting 53

9 DESCRIPTION 54

9.1. Frequency 54

9.2. FHSS (Frequency Hopping Spread Spectrum) 54

9.3. Signal Flowchart in the Whole System 56

10 EXPLANATION OF LINK DATA COMMUNICATION 57

10.1. Calling 57

10.2. To Terminate Communication 57

10.3. Ringing 57

11 BLOCK DIAGRAM (BASE UNIT_MAIN) 58

12 CIRCUIT OPERATION (BASE UNIT_MAIN) 59

12.1. DSP (Digital Speech/Signal Processing: IC501) 59

12.2. Flash Memory (IC601) 59

12.3. Power Supply Circuit 60

12.4. Reset Circuit 62

12.5. Telephone Line Interface 63

12.6. Auto Disconnect Circuit 64

12.7. Parallel Connection Detect Circuit 65

12.8. Calling Line Identification (Caller ID)/Call Waiting Caller ID

13 BLOCK DIAGRAM (BASE UNIT_RF PART) 68

14 BLOCK DIAGRAM (HANDSET_RF PART) 69

15 CIRCUIT OPERATION (RF PART) 70

15.1. Power Supply Circuit 71

15.2. 2.4GHz Mod/Demod Circuit 72

15.3. 5.8GHz Converter Circuit 73

15.4. 5.8GHz PA (Power Amplifier), 5.8GHz LNA (Low Noise

Amplifier) and Antenna Switch Circuit 74

16 BLOCK DIAGRAM (HANDSET) 75

17 CIRCUIT OPERATION (HANDSET) 76

17.1. Construction 76

17.2. Power Supply Circuit 77

17.3. Charge Circuit 78

17.4. Ringer and Handset SP-Phone 78

17.5. Sending Signal 79

Note:

Because CONTENTS 4 is the extract from the Operating Instructions of this model, it is subject to change without notice. You can

download and refer to the original Operating Instructions on TSN Server for further information.

CONTENTS

Page Page

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

17.6. Reception Signal 79

18 CIRCUIT OPERATION (CHARGER UNIT) 80

19 SIGNAL ROUTE 81

20 CPU DATA (BASE UNIT) 83

20.1. IC501 83

21 CPU DATA (HANDSET) 84

21.1. IC201 84

22 EXPLANATION OF IC TERMINALS (RF PART) 85

22.1. IC701 85

22.2. IC801 86

22.3. IC851 87

23 HOW TO REPLACE THE FLAT PACKAGE IC 88

23.1. PREPARATION 88

23.2. FLAT PACKAGE IC REMOVAL PROCEDURE 88

23.3. FLAT PACKAGE IC INSTALLATION PROCEDURE 89

23.4. BRIDGE MODIFICATION PROCEDURE 89

24 CABINET AND ELECTRICAL PARTS (BASE UNIT) 90

25 CABINET AND ELECTRICAL PARTS (HANDSET) 91

26 CABINET AND ELECTRICAL PARTS (CHARGER UNIT) 92

27 ACCESSORIES AND PACKING MATERIALS 93

27.1. KX-TG5671S 93

27.2. KX-TG5672B 94

27.3. KX-TG5673B 95

27.4. KX-TGA560B 96

28 TERMINAL GUIDE OF THE ICs, TRANSISTORS AND DIODES

28.1. Base Unit 97

28.2. Handset 97

29 REPLACEMENT PARTS LIST 98

29.1. Base Unit 98

29.2. Handset 100

29.3. Charger Unit 103

29.4. Accessories and Packing Materials 103

29.5. Fixtures and Tools 103

30 FOR SCHEMATIC DIAGRAM 105

30.1. Base Unit (SCHEMATIC DIAGRAM (BASE UNIT_MAIN))

105

30.2. Handset (SCHEMATIC DIAGRAM (HANDSET_MAIN))

105

30.3. Charger Unit (SCHEMATIC DIAGRAM (CHARGER UNIT))

105

31 SCHEMATIC DIAGRAM (BASE UNIT_MAIN) 106

32 SCHEMATIC DIAGRAM (BASE UNIT_RF PART) 108

33 SCHEMATIC DIAGRAM (BASE UNIT_OPERATION) 110

34 SCHEMATIC DIAGRAM (HANDSET_MAIN) 112

35 SCHEMATIC DIAGRAM (HANDSET_RF PART) 114

36 SCHEMATIC DIAGRAM (CHARGER UNIT) 116

37 CIRCUIT BOARD (BASE UNIT_MAIN) 117

37.1. Component View 117

37.2. Flow Solder Side View 118

38 CIRCUIT BOARD (BASE UNIT_OPERATION) 119

38.1. Component View 119

38.2. Flow Solder Side View 120

39 CIRCUIT BOARD (BASE UNIT_RF PART) 121

40 CIRCUIT BOARD (HANDSET_MAIN) 123

40.1. Component View 123

40.2. Flow Solder Side View 124

41 CIRCUIT BOARD (HANDSET_RF PART) 125

42 CIRCUIT BOARD (CHARGER UNIT) 126

42.1. Component View 126

42.2. Flow Solder Side View 126

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

1 ABOUT LEAD FREE SOLDER (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that

contains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn),

Silver (Ag), and Copper (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair

work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.

Caution

•

• •

• PbF solder has a melting point that is 50°F ~ 70° F (30°C ~ 40°C) higher than Pb solder. Please use a soldering iron with

temperature control and adjust it to 700°F ± 20° F (370°C ± 10°C). In case of using high temperature soldering iron, please

be careful not to heat too long.

•

• •

• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F (600°C).

•

• •

• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible

and be sure that any remaining is melted prior to applying the Pb solder.

•

• •

• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the

opposite side (See the figure below).

1.1. Suggested PbF Solder

There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper

(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu), or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the

manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other

materials.

The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

1.2. How to Recognize that Pb Free Solder is Used

(Example: Handset P.C.B.)

IC201

IC241

PbF

IC801

IC701

IC851

125

114

2815

51 75

100

IC246

Marked

(Component View)

Note:

The location of the “PbF”mark is subject to change without notice.

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

2 FOR SERVICE TECHNICIANS

ICs and LSIs are vulnerable to static electricity.

When repairing, the following precautions will help prevent recurring malfunctions.

1. Cover plastic parts boxes with aluminum foil.

2. Ground the soldering irons.

3. Use a conductive mat on worktable.

4. Do not grasp IC or LSI pins with bare fingers.

3 CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer´s Instructions.

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

4 OPERATING INSTRUCTIONS

4.1. Battery

4.1.1. Battery Installation/Replacement

4.1.2. Battery Charge

Note for service:

The battery strength may not be indicated correctly if the battery is disconnected and connected again, even after it is fully

charged. In that case, by recharging the battery as mentioned above, you will get a correct indication of the battery strength.

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

4.1.3. Battery Level

4.1.4. Panasonic Battery Performance

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

4.2. Location of Controls

4.2.1. Base Unit

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

4.2.2. Handset

KX-TG5671S / KX-TG5672B / KX-TG5673B / KX-TGA560S / KX-TGA560B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema telefónico de Panasonic

Panasonic

Panasonic KXTS840 Manual de usuario

Panasonic

Panasonic KXTS21W - PHONE-2 L Manual de usuario

Panasonic

Panasonic Digital Super Hybrid System Manual de usuario

Panasonic

Panasonic KX-TVA50 Manual

Panasonic

Panasonic PanaVoice Courier Manual de usuario

Panasonic

Panasonic DBS 576 Manual de usuario

Panasonic

Panasonic KX-TSC11AGW Manual de usuario

Panasonic

Panasonic KX-TVM50 Manual de usuario

Panasonic

Panasonic KX-TDA50 Manual

Panasonic

Panasonic KX-TG5110M - 5.8 GHz DSS Expandable Cordless... Manual de usuario

Panasonic

Panasonic EASA-PHONE KX-T2310 Manual de usuario

Panasonic

Panasonic KXTSC50B - PHONE/ANSWER MACHINE Manual de usuario

Panasonic

Panasonic EASA-PHONE KX-T30850 Manual de usuario

Panasonic

Panasonic KX-TES824LA Manual de usuario

Panasonic

Panasonic KX-TD612NE Instrucciones de funcionamiento

Panasonic

Panasonic KX-TD308 Manual de usuario

Panasonic

Panasonic KX-TD500CE Manual de usuario

Panasonic

Panasonic KX-TS2365RUB Manual de usuario

Panasonic

Panasonic TDA 100 Manual de usuario

Panasonic

Panasonic KX-TPA65 Manual de usuario

Panasonic

Panasonic KX-TA1232 Manual de usuario

Panasonic

Panasonic KX-TS105W Manual de usuario

Panasonic

Panasonic Easa-Phone VA-30910 Manual de usuario

Panasonic

Panasonic KX-FPG381 Manual de usuario

Manuales populares de Sistema telefónico de otras marcas

Teleco

Teleco Perfect Voice Tis 16 Manual de usuario

AT&T

AT&T Network Adapter 25 Manual de usuario

AVE

AVE AF902R-CE Manual de usuario

Tynetec

Tynetec Advent xt Manual de usuario

Ericsson

Ericsson DCT1800-S Manual de usuario

NEC

NEC Electra Elite 192 Manual de usuario

Alcatel

Alcatel EASY REFLEXES 4200 Manual de usuario

Bticino

Bticino PABX 28D Manual de usuario

NEC

NEC SL 2100 Manual de usuario

Sonifex

Sonifex Phone In 6 Manual de instrucciones

TransTel Communications

TransTel Communications TD-824i Instrucciones de montaje

Nortel

Nortel BCM50 Manual del producto

ASCOM

ASCOM TD 92375GB Manual del propietario

Karel

Karel MS26S Hoja de información del producto

EnGenius

EnGenius DuraFon PRO Manual de usuario

Teledat

Teledat X130 DSL Manual de usuario

SpectraLink

SpectraLink MOG400 Manual de usuario

LG-Nortel

LG-Nortel 300 Series Instrucciones de funcionamiento y seguridad