Panasonic EYFME1C Manual de usuario

Unauthorized copying and distribution is a violation

of law.

Order Number PTD1710E39CE

Cordless Right Angle Impact

Model No. EYFME1C

Europe

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 6

5 Appendix -----------------------------------------------------------11

6 Exploded View and Replacement Parts List -----------12

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please

use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-

ing iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).

2 Specifications

3 Troubleshooting Guide

3.1. Troubleshooting Guide

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

3.2.2. Operation

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Check whether the tool operates properly in both the forward and reveres directions.

• Set the LED light to switch-linked mode (L2) and check whether the LED light turns on when the trigger is engaged and that it

turns off when the trigger is released.

• Set the buzzer to each of its three modes and verify that there is no buzzer in b0 mode, that the buzzer sounds when the green

lamp is on in b1 mode, and that the buzzer sounds when the Red lamp is on b2 mode.

• Check whether the ID setting has been properly configured after repair and reassembly.

[ Method of confirmation ]

1. Press D button on the remote control

2. Confirm the operation panel display

• Initializing all settings (revert settings to factory defaults).

[ Setting method ]

3.2.3. Integrity

• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.

4 Disassembly and Assembly Instructions

* To reduce the risk of injury, always remove battery pack before removing/installing the tool.

* To assemble the tool, start with 4-10 and proceed to 4-1.

4.1. How to remove the gear case assembly

4.2. How to remove the SQ bevel gear assembly and bevel pinion assembly

4.3. How to remove the housing B

4.4. How to remove assemblies

4.5. Precautions when removing the module assembly

4.6. Checking and setting the module assembly’s DIP switches

4.7. How to remove the anvil, anvil bushing, thrust plate and slider

4.8. How to remove the driving shaft assembly and motor mounting plate

assembly

4.9. How to remove the driving shaft assembly

4.10. Caution in replacing the switch (WEYFGA1NK207)

4.11. Wiring and Assembly Points

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Panasonic

Panasonic

Panasonic EY46A5 Manual de usuario

Panasonic

Panasonic EYFLA9C Manual de usuario

Panasonic

Panasonic 4541OLOA Manual de usuario

Panasonic

Panasonic EY46A5 Manual de usuario

Panasonic

Panasonic EY3610 Manual de usuario

Panasonic

Panasonic EYFLA4A Manual de usuario

Panasonic

Panasonic EY75A8 Manual de usuario

Panasonic

Panasonic EY4550 Manual de usuario

Panasonic

Panasonic EY4550 Manual de usuario

Panasonic

Panasonic EY74A2 Manual de usuario

Panasonic

Panasonic EYFLA4 Manual de usuario

Panasonic

Panasonic EY4541 Manual de usuario

Panasonic

Panasonic EY4542 - CIRCULAR SAW 14.4V Manual de usuario

Panasonic

Panasonic EY4541X Manual de usuario

Panasonic

Panasonic EYFLA4A Manual de usuario

Panasonic

Panasonic EY3640 Manual de usuario

Panasonic

Panasonic EY75A8 Manual de usuario

Panasonic

Panasonic EYFMH1WC Manual de usuario

Panasonic

Panasonic EY3610 Manual de usuario

Panasonic

Panasonic EY4541X57 Manual de usuario

Panasonic

Panasonic EY7550LR2S Manual de usuario

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Manual de usuario

Panasonic

Panasonic EYFPA1C Manual de usuario

Panasonic

Panasonic EY7552X57 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual