OPTO-EDU A23.0910 Manual de usuario

www.optoedu.com Page 1 of 14 sale@cnoec.com

To ensure the safety and obtain satisfactory performance, please study

this instruction manual thoroughly before start to use your instrument.

A23.0910

Zoom Stereo Microscope, Parallel Light,

0.63x~8x,1:12.5

Instruction Manual

Contents

A23.0910

www.optoedu.com Page 2 of 14 sale@cnoec.com

Before Use

1. Components............................................................................................................................... 4

2. Assembling................................................................................................................................ 5

2-1 Assembling Scheme ......................................................................................................... 5

2-2 Assembling Steps............................................................................................................. 6

3. How to Use................................................................................................................................ 9

3-1 Set Illumination ............................................................................................................... 9

3-2 Adjust the Reflector ......................................................................................................... 9

3-3 Adjust the Focusing Tension......................................................................................................9

3-4 Adjust the Diopter and Focus........................................................................................ 10

3-5 Adjust the Interpupillary Distance ................................................................................ 10

3-6 Adjust the Elevation Angle of Observation Head .......................................................... 10

3-7 Turn on/off the Magnification Fixed Position Function................................................ 11

3-8 Use the Eye-cap............................................................................................................. 11

3-9 Adjust the Aperture Diaphragm..................................................................................... 12

3-10 Select the Light Path.................................................................................................... 12

3-11 Assemble and Use the CTV Adapter ............................................................................ 12

3-12 Assemble and Use the Polarizer Device...................................................................... 13

4. Troubleshooting.......................................................................................................................14

Before Use

A23.0910

www.optoedu.com Page 3 of 14 sale@cnoec.com

1. Operation Notice

Fig. 1

1. As the microscope is a high precision instrument,

always operate it with care, and avoid physical shake

during the operation.

2. Do not expose the microscope in the sun directly,

either not in the high temperature, damp, dust or acute

shake. Make sure the worktable is flat, horizontal and

firm enough.

Following environment is required when operating:

Indoor temperature: 5℃～40℃, Max relative humidity:

80%.

3. When moving the microscope, use both hands to hold

the position① and ② of the microscope. (See Fig.1)

★ It will damage the microscope by holding the

observation head, focusing knob, body or objectives

when moving.

4. External power adapter is used. Wide voltage range is

supported as 100~240VAC.

5. Use the special wire supplied by our company.

2. Maintenance

1. Keep all the surface of the lens clean. Wipe the lens gently with a soft lens tissue or blow

away the dust. Carefully wipe off oil or fingerprints on the lens surfaces with tissue

moistened with a little of 3:7 mixture of alcohol and ether.

2. Do not use organic solution to wipe the surface of other components, especially the surface

of plastic components. Please use the neutral detergent if necessary.

3. Never disassemble the microscope yourself, otherwise it will influence its function or

damage it.

4. After using, cover the microscope with a dust cover to prevent it from the dust, and store it

in a place free from moisture to avoidrusting.

5. To keep the performance of the microscope, please check it periodically. For more details,

please contact the agents nearby.

www.optoedu.com Page 4 of 14 sale@cnoec.com

Light Path

Selecting Pole

Aperture Diaphragm

Adjusting Rod

Tension

Adjusting

Knob

Main

Objective

Worktable

1. Components

A23.0

Microscope Body

Focusing

Bracket

Group

Coarse

Focusing

Knob

Clip

Base Group

Trinocular

Head

Eyepiece

Zooming

Knob

Lock

Knob

Fine

Focusing

Knob

Reflector Knob

www.optoedu.com Page 5 of 14 sale@cnoec.com

2-1 Assembling Scheme

Following is the Assembling Scheme to describe how to assemble the components, and the

numbers denote the assembling order.

★Before assembling, make sure there is no dust, dirt or other materials which will disturb

it. Assemble carefully and do not scrap any part or touch the glass surface.

2. Assembling A23.0910

A23.0910

www.optoedu.com Page 6 of 14 sale@cnoec.com

2-2 Assembling Steps

Fig. 2

Fig. 3

Fig. 4

2-2-1 Assemble the Focusing Bracket Group

Loosen the lock knob① of the focusing bracket group,

insert the hole② of focusing bracket group into the

column③, until the focusing bracket group to the

lowest position. Then tighten the lock knob① to prevent

the microscope from turning.

◎Slowly insert it, do not force too much.

◎ To avoid the microscope turnover, the focusing

bracket group must assemble on the same side to the

worktable of base group, as the left view of Fig. 3. If

assemble the focusing bracket group on the wrong side,

the microscope will turn over as the right view of Fig. 3.

2-2-2 Assemble the Microscope Body

1) Remove the decorative cover① of the focus bracket

group, and loosen the M4 inner hexagon screw with a

M4 inner hexagon spanner. (See Fig. 4)

2) Match the dovetail interface③ of the microscope

body with the dovetail groove② of the focus bracket

group, and insert it from top to bottom as the direction

shown in the figure.

3) Tighten the M4 inner hexagon screw on the focus

bracket group with a M4 inner hexagon spanner, then

put the decorative cover①back.

2-2-3 Assemble theObjective

1) Rotate the objective as the arrowhead direction shown

in the figure, and screw the objective ② into the

objective installation screw hole①. (See Fig. 5)

Fig. 5

A23.0910

www.optoedu.com Page 7 of 14 sale@cnoec.com

Fig. 6

2-2-4 Assemble the Head

1) Loosen the head lock-screw① fully with a M4 inner

hexagon spanner.

2) Make the two tubes face forward, from a little rear

position of the center, insert the coattail interface on the

bottom of head into the hole of body with a little rear

inclined. Match the orientation groove② of the head

with the orientation pin③ of the body, and then screw

down the lock screw①. (See Fig. 6)

2-2-5 Assemble the Eyepiece

1) Take down the eyepiece tube cover①.

2) Insert the eyepiece③ into the eyepiece tube, until it

touches the bottom. Lock the eyepiece by the lock-screw

② (See Fig. 7)

Fig. 7

Fig. 8

◎Install or Remove the Reticle

1) Unscrew the pressure ring from eyepiece (see Fig. 8).

2) Clean the reticle, then install it into the pressure ring

with the scaled surface upward (see Fig. 8).

3) Screw the pressure ring which is with reticle into the

eyepiece until tight enough.

4) To remove the reticle, first unscrew the pressure ring

from eyepiece, then take down the reticle and keep it

with clean paper packed.

2-2-6 Assemble (Remove) the Worktable

1) Place the worktable on the installation hole of the

base.

2) To remove the worktable, use fingertip to press down

the worktable nearby the pillar edge (as the arrowhead

direction shown in Fig. 9), then the other end of

worktable will turn up. (See Fig. 9)

Fig. 9

Press

down

A23.0910

www.optoedu.com Page 8 of 14 sale@cnoec.com

Fig. 10

Fig. 11

Fig. 12

2-2-7 Assemble the Clip

1) Use the clip to avoid the specimen moving.

2) Insert the clip① into the two holes of the base, as the

arrowhead direction shown in the figure. (See Fig. 10)

2-2-8 Fix the Microscope BodyPosition

1) Loosen the lock knob①, and rotate the microscope

body and the focusing bracket group left and right.

2) Match the center of zoom body group with the center

of worktable, then lock the lock knob①. (See Fig. 11)

2-2-9 Connect the LED Light Source and PowerCord

1) Make sure the main switch is at “O” (OFF)

position.(See Fig. 12)

2) Insert one end of the optical fiber①into the inner

hole② of the power supply box to the bottom, and align

the flat surface with the lock screw③, then lock it with

the lock screw③.

3) Insert the other end of the optical fiber① into the

hole of the base④, then lock it with the lock screw.

4) Insert one end of the power adapter⑥ into the inner

hole⑤ of the power supply box.

5) Insert one end of the power cable ⑦ into the

corresponding hole of the power adapter⑥, and the

other end into the power supply socket.

★ The power supply box supports wide voltage as

100-240V.

★ Don’t use strong force when the power cord is

bended or twisted, otherwise it will be damaged.

★ Use the special wire supplied by our company. If

it’s lost or damaged, choose one with the same

specifications.

★ Connect the power cord appropriately to make

sure the instrument is connected to ground.

www.optoedu.com Page 9 of 14 sale@cnoec.com

3-1 Set Illumination

1) Put through the power and turn on the main power

switch to“ON”.

2) Adjust the light adjustment knob ② until the

illumination is comfortable for observation. Rotate the

light adjustment knob clockwise to raise the

brightness. Rotate the light adjustment knob

counterclockwise to lower the brightness(See Fig.13).

Fig. 13

Fig. 14

Fig. 15

3-2 Adjust the Reflector

◎ The reflector has two surfaces, one is plane mirror,

the other is sandblasted aluminum. Both surfaces can

reflect the light, but the reflection of plane mirror is

stronger.

1) Adjusting the adjustment knob ① of the

reflector(See Fig. 14), can change the reflector surface,

also can change the lighting range after reflected.

2) The adjustment knob① of the reflector can be

moved front and rear according to the arrowhead

direction, to achieve different lighting effects.

3-3 Adjust the Focusing Tension

1) If the handle is very heavy when coarse focusing,

or the specimen leaves the focus plane soon after

focusing, or the stage declines itself, these problems

can be solved by adjusting the tension adjustment ring

①.(See Fig.15)

2) Rotate the tension adjustment ring① according to

the arrow direction in the figure, to tighten the

focusing system; rotate the tension adjustment ring①

in the opposite direction, to loosen the focusing

system.

3. How to Use A23.0910

A23.0910

www.optoedu.com Page 10 of 14 sa[email protected]

Left diopter Right diopter

adjustment

3-4 Adjust the Diopter and Focus

★ Before operating, make sure the eyepiece lock

screw is tighten.

1) Rotate the zoom knob to the maximum

ring adjustment

ring

Fig. 16

Fig. 17

magnification. (See Fig. 15)

2) Rotate the focusing knob if the image is unclear

when observed with the right eyepiece.

3) Rotate the zoom knob to the minimum

magnification.

4) Rotate the diopter adjustment ring of right eyepiece

if the image is unclear when observed with the right

eyepiece. (See Fig. 16)

5) Then rotate the zoom knob to the maximum

magnification, if the image is not clear enough when

observed with the right eyepiece, repeat Step (3)~(5)

as above.

6) Then rotate the zoom knob to the minimum

magnification, turn the diopter adjustment ring of left

eyepiece if the image is not clear enough when

observed with the left eyepiece. (See Fig. 16)

3-5 Adjust the Interpupillary Distance

Hold the left and right prism boxes and rotate them

according to the arrowhead pointed in Fig. 17, until

it’s comfortable to view.

Adjustable range: 50~76mm.

Fig. 18

3-6 Adjust the Elevation Angle of ObservationHead

1) Adjust the height and elevation of observation tube

to the most comfortable position for observation.

2) Use both hands to hold the binocular components,

to move it up or down to the position required. (See

Fig. 18)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microscopio de OPTO-EDU

OPTO-EDU

OPTO-EDU A13.2604-B Manual de usuario

OPTO-EDU

OPTO-EDU A15.2603 Manual de usuario

OPTO-EDU

OPTO-EDU A41.1950 Manual de usuario

OPTO-EDU

OPTO-EDU A14.1063 Manual de usuario

OPTO-EDU

OPTO-EDU A12.1303 Manual de usuario

OPTO-EDU

OPTO-EDU MDJ A13.2602 Manual de usuario

OPTO-EDU

OPTO-EDU A22.1201 Manual de usuario

OPTO-EDU

OPTO-EDU A13.2603 Manual de usuario

OPTO-EDU

OPTO-EDU A16.2615-L Manual de usuario

OPTO-EDU

OPTO-EDU A11.2601 Manual de usuario

OPTO-EDU

OPTO-EDU A23.3645 Series Manual de usuario

OPTO-EDU

OPTO-EDU A33.1501 Manual de usuario

OPTO-EDU

OPTO-EDU A18.1825-LCD Manual de usuario

OPTO-EDU

OPTO-EDU A17.1091 Manual de usuario

OPTO-EDU

OPTO-EDU A24.1001 Manual de usuario

OPTO-EDU

OPTO-EDU A13.1005-B Manual de usuario

OPTO-EDU

OPTO-EDU A15.1302 Manual de usuario

OPTO-EDU

OPTO-EDU A11.1303 Series Manual de usuario

OPTO-EDU

OPTO-EDU EX31 Series Manual de usuario

OPTO-EDU

OPTO-EDU A22.0302 Manual de usuario

OPTO-EDU

OPTO-EDU A23.1502 Series Manual de usuario

OPTO-EDU

OPTO-EDU A12.1061 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1016 Manual de usuario

OPTO-EDU

OPTO-EDU A10.1018 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario