OPTO-EDU A41.1903 Manual de usuario

www.optoedu.com Page 1 of 14 sa[email protected]m

To ensure the safety and obtain satisfactory performance, please study this

instruction manual thoroughly before start to use your instrument.

A41.1903

Operating Microscope, One Head 0~180°,

Manual Step Zoom, 4.8x~16x, For Dental, ENT,

Ophthalmology, Gynecology

Instruction Manual

www.optoedu.com Page 2 of 14 sa[email protected]m

A41.1903 + beam slitter + demonstrator + video camera adapter + digital camera + computer

General Description

Operation Microscope Model A41.1903 (hereafter referred to as simply instrument) is a medical optical

instrument with multiple function and application. The optical system of the instrument equipped with

0-180°inclinable binocular and magnification change system which offers 3-step magnification change.

Fine focusing can be done by objective fine adjusting lever. Two objectives are available for different

working distance and magnification. The illumination system of the instrument adopts coaxial

illumination with 10W LED light source. The optical system of the instrument can be fitted with a

beamsplitter, which makes video camera adapter and demonstrator attachable. Photos or moving

photos can be taken during operation after connecting CCD camera or digital CCD camera with

instrument. The beamsplitter, video camera adapter, CCD camera (C-mount 1/3 inch video camera

attachable) and demonstrator are optional.

www.optoedu.com Page 3 of 14 sa[email protected]m

The instrument is suitable for various diagnosis, examination and general microscope operation. Due to

its flexible and stable structure and easy operation, the instrument can be widely used for

micro-operation in dental especially, and also can be used for micros-operation in ophthalmology,

ear-nose-throat, gynecology and surgery.

The Environment For Use

a) Transport and Storing

● Ambient Temperature Range: -40℃-55℃

● Relative Humidity Range: 10%-80%

● Barometric Pressure Range: 500 hPa-1060 hPa

b) Operation

● Ambient Temperature Range: 5℃-40℃

● Relative Humidity Range: 30%-80%

● Barometric Pressure Range: 700 hPa-1060 hPa2

1. Precautions

1.1 After unpacking the carton, check the parts against the packing list first. If there is any

difference, contact the sales department to protect your benefit.

1.2 When carrying and unpacking the carton, pay attention that the arrow on the carton shall be at

upward position. Handle the instrument with care to prevent it from being damaged.

1.3 The instrument shall be used and kept in a clean and dry place with constant temperature in

order to ensure the lifetime of the component in the instrument. Before using the instrument,

make sure to step down the brake on the foot wheel to prevent the instrument from sliding to

avoid accident. When moving the instrument in the room, it is recommended to push it at the

lower part to prevent the instrument from being upset and damaged.

1.4 Do not touch the surface of the lens and prism with hand or hard objects.

1.5 When the LED bulb is broken and has to be replaced, make sure that the power is off and the

bulb is fully cool down in order to prevent your finger from being hurt. Never touch the glass

surface of the illumination bulb (LED bulb) with your finger directly. If the bulb surface is found

oily and dirty, it shall be cleaned with flannelette soaked with alcohol before usage.

1.6 The counterweight of the base of the instrument is limited. When the arm is stretched, never

press the instrument with strong force. Otherwise, the instrument can go down to get the

operator or the instrument itself damaged.

1.7 Before using the instrument, make sure the connecting parts are fastened or adjusted to right

position to avoid accident caused by the failure of the parts.

1.8 Never move any part of the instrument with strong force. Adjustment shall be done according

to the instruction, especially for the operation handle, it shall not be turned with over force to

prevent it from impacting the arm to get the components damaged.

1.9 Power shall be switched off after using the instrument. After use, the instrument shall be

cleaned and covered with plastic cover to prevent dust.

2. Main Technical Data

2.1 Input voltage: AC100-240V, frequency: 50HZ-60HZ

www.optoedu.com Page 4 of 14 sa[email protected]m

2.2 Output: DC12V3A, 36W

2.3 Table of Optical Characteristics for A41.1903 Operation Microscope:

A41.1903 Series Operation Microscope Optical Characteristics

Eyepiece

WF12.5x/20mm

Focal Length (mm)

F=200mm

F=250mm

F=300mm (Optional)

F=400mm

(Optional)

Zoom Body

1.6x

1.0x

0.6x

1.6x

1.0x

0.6x

1.6x

1.0x

0.6x

1.6x

1.0x

0.6x

Total Magnification

16x

10x

6.0x

12.8x

8.0x

4.8x

10.7x

6.7x

4.0x

8.0x

5.0x

3.0x

Linear Field (mm)

15.0

24.0

40.0

19.0

30.0

50.0

23.0

37.0

60.0

30.0

48.0

80.0

Diameter of Spot

57.00 mm

71.00 mm

86.00 mm

113.00 mm

Exit Pupil Distance

20.00 mm

Eyepiece

WF10x/23mm

Focal Length (mm)

F=200mm

F=250mm

F=300mm (Optional)

F=400mm

(Optional)

Zoom Body

1.6x

1.0x

0.6x

1.6x

1.0x

0.6x

1.6x

1.0x

0.6x

1.6x

1.0x

0.6x

Total Magnification

12.8x

8.0x

4.8x

10.2x

6.4x

3.8x

8.5x

5.3x

3.2x

6.4x

4.0x

2.4x

Linear Field (mm)

16.0

26.5

43.0

20.0

33.0

53.0

24.5

39.5

64.5

32.0

52.5

85.5

Diameter of Spot

57.00 mm

71.00 mm

86.00 mm

113.00 mm

Exit Pupil Distance

25.00 mm

2.4 Table of Specification for A41.1903 Operation Microscope：

Model

A41.1903

Binocular Head

Tilting 0~180°

Main Usage

Dental, ENT, Ophthalmology, Gynecology

Total Magnification

With Objective F=200mm: 6.0x, 10x, 16x

With Objective F=250mm: 4.8x, 8.0x, 12.8x

Total Magnification

(Optional)

With Objective F=300mm: 4.0x, 6.7x, 10.7x

With Objective F=400mm: 3.0x, 5.0x, 8.0x

Eyepiece

WF12.5x/20mm

Head Magnification

Interpupillary Distance

50~80mm Adjustable

Diopter

Both Left & Right Eyetube Diopter Adjustable ±7D

Zoom Body

3 Steps Zoom: 0.6x,1.0x,1.6x

Objective

F=200mm For Ear, Nose, Ophthalmology

F=250mm For Dental

Objective (Optional)

F=300mm For Ear, Nose

F=400mm For Throat

Focusing

Fine Focusing Range 10mm

Filter

Green, Yellow Filters Built-in

Balancing Arm

2-Part Arm With Universal Joints, Counterweight Adjustable And Lockable

Stand

2-Part Column + Five Star Base With Caster

Illumination System

Coaxial Illumination, 10W LED, Brightness Adjustable, >40000 Lux

Power Supply

Wide Range AC100~240V, DC12V 3A, 36W

3. Overall Structure of Instrument

www.optoedu.com Page 5 of 14 sa[email protected]m

1. Base with wheels 2. Column 3. Power supply box 4. LED lamp plug

5. Torque adjusting hand wheel 6. Arm assembly 7. 0-180°Binocular 8. Eyepiece

9. CCD camera (optional) 10. Demonstrator (optional) 11. Beamsplitter (optional)

12. Magnification changer 13. Video camera adapter (optional)

4. Working Principle and Function of Main Parts

4.1 Head of Microscope

It is the main part of microscope, can connect beamsplitter, video camera adapter, Demonstrator,

www.optoedu.com Page 6 of 14 sale@cnoec.com

Photo adapter and other accessories.

(1) Universal joint: Used to adjust viewing angle and direction.

(2) Filter: Built-in green and yellow filters.

(3) Magnification changer knob: Magnification can be changed

by turning this knob.

(4) Binocular with eyepiece: 8X.

(5) Eyepiece: 12.5X.

(6) Fine focusing lever: It is used for fine focusing.

(7) Objective: F=200mm & F=250mm

(8) Handle: If the position of the lever is to be changed, press

the button and turn the handle to the desired position. Then

release the button.

(9) LED lamp power line.

4.2 Power supply box

It is an illumination control unit for the operation microscope.

The power supply box is connected the arm and column; it is

also used as part of the arm.

(1) Locking hand wheel

(2) Power input socket for power supply adapter DC12V3A

(3) DC output socket for LED lamp

(4) Arm rotation limit screw

(5) DC12V output socket for camera

(6) Brightness control knob

(7) Power switch

Note: Non-professional maintenance staffs do not open the power supply box.

4.3 Arm assembly (see Figure 1)

The arm assembly is an important part for supporting and moving the microscope and accessories.

The optical system of the microscope, which consists of the rotating drum magnification change

system, binocular observation unit and objective, is mounted on the arm assembly. The arm

assembly can be moved to any desired position during operation. It is stable and reliable. You can

adjust the counterweight of microscope and lock the arm.

Torque adjusting hand wheel 6: It is used to keep the arm in balance when accessories are added to

the microscope or reduced from the microscope. Locking hand wheel: After the instrument is

adjusted in place, lock this hand wheel to make the instrument stable.

4.4 Power supply adapter

It provide DC12V3A power for power supply box, We provide various

standardAC power plugs according to the customer’s requirement.

(1) AC power plug (European standard)

(2) Cable length 3m with Magnetic ring

www.optoedu.com Page 7 of 14 sa[email protected]m

(3) Output connector (Coaxial 5.5x2.1mm plug)

Note: Non-professional maintenance staffs do not open the power supply adapter.

4.5 The description of other parts is as follows (see Figure 1):

a. Beamsplitter 11 (optional): It is used to divide the light. It is

provided with connections at left and right side for the connection of

video camera adapter and demonstrator or SLR camera adapter etc.

(1) Connector for video camera adapter, demonstrator or photo

adapter

(2) Locking screw

b. Video camera adapter 13 (optional): It is a component connected

to the beamsplitter for optical image forming. It is suitable

connected to video camera, which connector is 1/3 inches “C” or

“CS”.

1) Screw connector, which connects with video camera

(2) Connector, which connects with beamsplitter

(3) Focusing hand wheel

(4) Locking screw8

c. Demonstrator 10 (optional): It is a monocular observation unit

connected to the beamsplitter. It can be used for observation at the

same time with the binocular observation unit.

(1) Eyepiece

(2) Connector, which connects with beamsplitter

(3) Image rotating hand wheel

(4) Observation position changer

d. SLR camera adapter (optional) It is an optical image-forming

component that is connected to the beamsplitter. It is connected to

a SLR camera or SLR digital camera with Nikon mount or Canon

mount for photo taking. Please contact with supplier.

(1) Connector, which connects with beamsplitter

(2) Connector, which connects with SLR camera

(3) Focusing handwheel

5. Installation of Instrument

5.1 Installation of floor stand with wheels

Insert the column into the hole in base and tighten threaded nut.

5.2 Installation of power supply box

Put the box on the top of the column and tighten locking handwheel

www.optoedu.com Page 8 of 14 sa[email protected]m

5.3 Installation of arm

Loosen arm rotating angle limit screw and locking handwheel on the power box, insert the shaft of

arm into hole in the power box and screwing in arm rotating angle limit screw and locking

handwheel in power supply box. Insert the LED lamp plug into the DC output socket for LED lamp of

power supply box. Note: The maximum rotation of the arm assemble shall not be more than 360 º.

Otherwise, the LED lamp power line might be damaged.

5.4 Installation of beamsplitter (beamsplitter is optional)

Loosen screw of Magnification changer, fit beamsplitter then tighten screw.

5.5 Installation of binocular. The binocular is fitted in the same as 5.4

5.6 Change objectives

Turn the focusing lever clockwise, get down the objective fixed on magnification changer, then

screw on the objective you need. Turn fine focusing lever counterclockwise to make the fine

focusing lever in the middle position.

5.7 Installation of operation handle

Fix the operation handle on the head of microscope with 2 pcs screws

5.8 Installation of video camera adapter (video camera adapter is optional)

Insert video camera adapter into the mount of the beamsplitter and tighten the nut.

5.9 Installation of demonstrator (demonstrator is optional)

Insert demonstrator into the mount of the beamsplitter and tighten the nut.

6. Adjusting of Instrument

6.1 The elevation of the arm and adjustment of the torque balance When the accessory is reduced

from the microscope, the microscope is out of balance. Turn torque adjusting handwheel to make

the microscope in balance. Loose handwheel and let the arm go up and down over a wide range.

When the arm is adjusted in the right height, tighten the handwheel.

6.2 Adjustment of universal coupling arm

The torque of the universal coupling arm is adjusted by the manufacturer before the instrument is

www.optoedu.com Page 9 of 14 sa[email protected]m

delivered. If the used finds the torque not suitable (too loose or too tight when turning), it can be

adjusted by special person in the following way:

6.2.1 Screw off locking knob 1, screw 2 and nut 3. Tighten nut 4 to increase torque or vice versa.

Then screw down nut 3, tighten screw 2 and screw 2 and screw in knob 1.

6.2.2 The torque adjustment of locking knob 6 is the same as that of locking knob 1. The torque is

adjusted by nut 7.

7. Operation of instrument

7.1 Connect the power supply adapter with power supply box, and connect the power supply

adapter with power socket

7.2 Press power switch. Turn dimmer knob for proper brightness. Note: Before switching off the

power, make sure that the brightness is adjusted to minimum to prevent the lamp from being

damaged when switching on again.

7.3 Hold handle, align the microscope with the object to be observed and move the microscope up

and down, left and right till a distinct image is seen by the operator (The eyecup can be rolled down

if the observer wears glasses). Then tighten handwheel. Fine focusing can be done by fine focusing

lever during operation.

7.4 If the objective is to be replaced for magnification change, refocusing will be needed after

replacement. (i.e. repeat step 7.3)

7.5 Step down the foot wheel brake during operation to present the instrument from being moved.

8. Care and Maintenance

The instrument shall be placed in a dry, dust-free and well-ventilated room where no corrosive

chemicals are stored. The instrument shall not be disassembled by non-professional people,

especially the optical part. Never touch the glass surface with finger. If the dust, dirt and oil on the

glass surface is to be cleaned, first clean the dust off the surface with a clean and soft brush, then

wipe the surface gently with degreased cotton soaked with a little absolute alcohol. The glass

surface shall not be wiped frequently to avoid damage to the surface. The instrument shall be

covered with clean cloth when it is not in use.

Often by the relative moisture shall be less than 80%, temperature shall be within 5 - 40ºC without

temperature shock. It is forbidden to disassemble the instrument by an unqualified person,

especially for optical parts, Do not touch the glass surface with finger directly. When cleaning, wipe

the glass surface with absorbent cotton slightly moistened with absolute alcohol after the glass

surface has been cleaned of dust with a clean and soft brush. Wipe it as few times as possible to

avoid damage to the glass surface. Cover the instrument with a clean cloth cap when it lies in idle.

9. Transportation and Storage

During transportation, the instrument shall be placed according to the indication marked on the

www.optoedu.com Page 10 of 14 sale@cnoec.com

package. Pay attention to moisture and vibration. If the instrument is to be stored for a long period, it

shall be cleaned and put into the package and kept in a dry and well ventilated store room without

any corrosive chemicals. The relative humidity of the room shall not exceed 80% and the

temperature shall be controlled in the range of -40 °C - 55 °C without any temperature shock.

10. Trouble-shooting Guide

In case there is any trouble, please first refer to the trouble-shooting guide. If it still cannot work,

please contact the authorized distributor.

Trouble

Possible reason

Remedy

No working

Power supply adapter is not connected

Connect the power supply adapter

No switch on the main power

Switch on the main power

Main power is broken-down

Contact a local electrician

Illumination

does not light

The LED lamp is not connected correctly

Connect again

No switch on the main power

Switch on the main power

Main power is broken-down

Contact a local electrician

Electric parts are broken-down

Contact the authorized distributor

The bulb is burnt

Replace the spare bulb

11. Fault Checking and Solution for LED illumination System.

After installation, power-on test according to user’s manual, or during using operation microscope, find

no light, please check according to the following steps:

11.1 Connect power supply adapter to power supply and power supply box. By this time, the indicator

light of power supply adapter is always on. Turn on the power switch on the power box. The power input

is normal if the switch indicator is on. The power input is abnormal if the switch indicator is off, please

check: A. Connection of the power supply adapter again. B. Where the power supply adapter is

damaged, if yes, please replace.

11.2 When the switch indicator is on, turn brightness control knob to the maximum, and checks the

Tabla de contenidos

Otros manuales de Microscopio de OPTO-EDU

OPTO-EDU

OPTO-EDU A16.1098 Manual de usuario

OPTO-EDU

OPTO-EDU A11.1323 Manual de usuario

OPTO-EDU

OPTO-EDU A11.1303 Series Manual de usuario

OPTO-EDU

OPTO-EDU A23.3645 Series Manual de usuario

OPTO-EDU

OPTO-EDU A15.1016 Manual de usuario

OPTO-EDU

OPTO-EDU MDJ A13.2602 Manual de usuario

OPTO-EDU

OPTO-EDU A13.0905 Manual de usuario

OPTO-EDU

OPTO-EDU A22 3660N Series Manual de usuario

OPTO-EDU

OPTO-EDU A11.0214 Manual de usuario

OPTO-EDU

OPTO-EDU A22.1504 Series Manual de usuario

OPTO-EDU

OPTO-EDU A11.2601 Manual de usuario

OPTO-EDU

OPTO-EDU A16.2615-L Manual de usuario

OPTO-EDU

OPTO-EDU A15.2603 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1091 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1302 Manual de usuario

OPTO-EDU

OPTO-EDU A11.1009 Series Manual de usuario

OPTO-EDU

OPTO-EDU A12.0910 Manual de usuario

OPTO-EDU

OPTO-EDU A13.2604-B Manual de usuario

OPTO-EDU

OPTO-EDU XD Series Manual de usuario

OPTO-EDU

OPTO-EDU A33.5121 Manual de usuario

OPTO-EDU

OPTO-EDU A12.1095 Manual de usuario

OPTO-EDU

OPTO-EDU A18.1825-LCD Manual de usuario

OPTO-EDU

OPTO-EDU A15.1018 Manual de usuario

OPTO-EDU

OPTO-EDU A41.1950 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario