OPTO-EDU A13.0905 Manual de usuario

www.optoedu.com 1/18 sale@cnoec.com

A13.0905

Inverted Metallurgical Microscope,

Semi-APO

Instruction Manual

This instruction manual is for the Invert Metallurgical microscope IE200

series. To ensure the safety and obtain optimum performance and to

familiarize yourself fully with use of this microscope, we recommend that you

study this manual thoroughly before operating the microscope. Retain this

instruction manual in an easily accessible place near the work desk for future

reference.

The instruction is according to industry standard JB/T10077-1999.

www.optoedu.com 2/18 sale@cnoec.com 
Contents 
 
 A13.0905 
Before using..............................................................................................3 
1. Nomenclature........................................................................................5 
2．Assemblage.........................................................................................7 
2-1 Assemblage scheme.....................................................................7 
2-2 Assemblage step..........................................................................8 
3. Operation.........................................................................................11 
3-1 Illumination...............................................................................11 
3-2 Focusing....................................................................................11 
3-3 Adjust tension of focus..............................................................11 
3-4 Adjust diopter............................................................................12 
3-5 Adjust inter-pupillary distance ..................................................12 
3-6 Use filter....................................................................................12 
3-7 Adjust field diaphragm..............................................................13 
3-8 Adjust aperture diaphragm ........................................................13 
3-9 Use simple polarizing kit ..........................................................14 
3-10 Replace fuse ............................................................................14 
3-11 Mount and use TV device........................................................14 
3-12 Mount and use photo device ...................................................15 
4.Technical Parameter ............................................................................16 
5．Troubleshooting................................................................................16 
 
 
 
 
 
 
 
 
 
 

www.optoedu.com 3/18 sale@cnoec.com

Before using A13.0905

Invert metallurgical microscope is used to discern and analyze organizational structure from

kinds of metal. It is very important in the work of quality research for foundry, smelt, heat

treatment and inspection for raw material and analysis for metallurgical structure of material after

processing. It is also the important tool of research work for metal physics, which is wildly used

in enterprise, university and R&D.

1. Attention:

1.1 As the microscope is precision

instruments, it should be taken carefully

and avoid impact during transportation.

1.2 Do not expose the microscope in the

sun directly, either not in the high

temperature, damp, dusty or acute

shake place. Make sure the worktable is

horizontal. Following environment is

required: Indoor temperature: 5℃～

40℃, Max relative humidity:80%.

1.3 To move the microscope, please hold

groove ①behind and tube position ②

and lay it carefully. (Fig. 1)

★It will be damaged by holding the stage, focusing knobs, tube or illuminator.

1.4 The lamp will be very hot during working, please make sure there is enough space around for

dissipating.

1.5 Please connect the microscope with ground to avoid lighting strike.

1.6 Please make sure the power switch is “0”(Off)(See the left Fig) and the bulb cool down

before replace the bulb or fuse.

★Bulb: 3W LED bulb

12V/30W halogen bulb (Philips 5761)

1.7 It adopt wildly voltage 90~240V, and do not need any transformer. Please make sure the

power supply before using.

1.8 Please use special wires supplier by our company.

Fig.1

www.optoedu.com 4/18 sale@cnoec.com

A13.0905

2. Maintenance

2.1 Clean the lenses gently with a soft lens tissue. Carefully wipe off oil or fingerprints on the

lens surfaces with tissue moistened with 3:7 mixture of ethanol and anther or dimethylbenzene.

★Ethanol and Anther are both flammable. Please leave them away from fire or fire source,

especially during the power switch turn on and turn off.

2.2 Don’t use organic solution to clean the surfaces of the microscope, especially for plastic parts.

Please use the neutral detergent if necessary.

2.3 If the microscope damped by the liquid during working, please cut off the power immediately

and make it dry.

2.4 Do not disassemble or assemble the microscope to avoid damaging the capability.

2.5 After using, put on dust cover to protect microscope.

3. Safety sign

Sign

Signification

It shows the surface gets hot and don’t touch with bare hand.

Read the introduction before using. Unsuitable operation would lead person hurt

or instrument faulty.

Power switch ON

Power switch OFF

www.optoedu.com 5/18 sale@cnoec.com

1. Nomenclature A13.0905

Mechanical stage

Eyepiece

Knob for adjustment

tension

Coarse knob

Fine knob

Analyser

Knob for

brightness

Pole for field

diaphragm

Pole for aperture

diaphragm

Polarizer slide

Filter slide

Metal stage

www.optoedu.com 6/18 sale@cnoec.com

A13.0905

Objective

IE200M stand

Power

switch

Trinocular

head

Centering screw for

field diaphragm

Diopter

adjustment ring

Reflected

illuminator

Nosepiece

Lamp

holder

www.optoedu.com 7/18 sale@cnoec.com

．

Assemblage

A13.0905

2-1Assemblage scheme

The below numbers shows the assemblage order.

★Before assemblage, please make sure all parts are without any dust or dirt..

★Be careful during assemblage and do not scrap or touch the optical lens.

Plug

Lamp

holder

Objecti

Metal stage

Clips

Eyepiec

analyzer

Polarizer

slide/filter slide

www.optoedu.com 8/18 sale@cnoec.com

A13.0905

2-2Assemblage step 2-2-1 Set lamp holder

b Make sure the pin ①and ③facing to the hole

②and ④, then lock. (Fig. 2)

★LED bulb: 3W

★Halogen bulb: 6V30W (Philips 5761)

2-2-2 Set or replace bulb

Use clean glove or gauze to hold the bulb and

make sure the bulb pin ①facing to hole ③

and lock. Please make sure the bulb should be

vertical. (Fig. 3)

★Do not touch the bulb by finger directly.

C lean by gauze if there is finger print on

bu bulb.

★Whenever replace the bulb, please cut

off the power first and wait the

illuminator part cool down.

2-2-3 Set objectives

Turn the coarse knob to make the nosepiece to

lowest. Through the hole on stage to set the

objectives ①on nosepiece from low

magnification to high magnification with the

direction. (Fig. 4)

★Clean the objectives regularly. It is very

sensitive of dust for objective of invert

microscope.

★Please use low magnification objective,

such as 5X or 10X to find image, then use

high one for observation.

★Make sure to hear click when turning to

show the objective on correct position.

Fig.3

Fig.4

Fig.2

www.optoedu.com 9/18 sale@cnoec.com

A13.0905

2-2-4 Set the metal stage

⑴Set the metal stage ①on mechanical

stage as the direction showed. (Fig. 5)

⑵Turn the metal stage to make the V hole

②direct to the user.

2-2-5 Set clips

⑴Take out clips ①from pole ②. (Fig. 6)

⑵Screw pole ②into hole ③on

mechanical stage, then lock by screw nut ④.

⑶Set the clips ①into pole ②and make it

direct to center of stage.

2-2-6 Set eyepiece

⑴Take off eyepiece cap ①. (Fig. 7)

⑵Insert the eyepiece ②to tube.

Fig.5

Fig.7

Fig.6

www.optoedu.com 10/18 sale@cnoec.com

A13.0905

2-2-7 Set Analyzer

Insert the analyzer ①into hole ②on

microscope stand with its face up to hear click.

(Fig.8)

2-2-8 Set polarizer and filter

Insert the polarizer or filter ①into hole ②on

connector between microscope stand and

illuminator with its face up to hear click.

(Fig.9)

2-2-9 Connect power supply

⑴Make sure the main power switch is at

“O”(OFF) position.

⑵Insert one side of power plug ①into

microscope socket ②and the other side

connecting to power supply. (Fig. 10)

★Don’t overexert with the wires when it

is bendy or voluble.

★Use the wire supplied by our company

only. If it is lost or damaged, choose

another suitable one.

★Connect all wires correctly, make sure

the microscope connect with ground.

Fig.8

Fig.10

Fig.9

Tabla de contenidos

Otros manuales de Microscopio de OPTO-EDU

OPTO-EDU

OPTO-EDU A33.1511 Manual de usuario

OPTO-EDU

OPTO-EDU A12.1010 Manual de usuario

OPTO-EDU

OPTO-EDU A33.1502 Manual de usuario

OPTO-EDU

OPTO-EDU A23.3645 Series Manual de usuario

OPTO-EDU

OPTO-EDU A22 3660N Series Manual de usuario

OPTO-EDU

OPTO-EDU A18.1831 Manual de usuario

OPTO-EDU

OPTO-EDU A34.5017 Manual de usuario

OPTO-EDU

OPTO-EDU A59.4231 Manual de usuario

OPTO-EDU

OPTO-EDU A17.1091 Manual de usuario

OPTO-EDU

OPTO-EDU A63.7015 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1302 Manual de usuario

OPTO-EDU

OPTO-EDU A15.2604 Manual de usuario

OPTO-EDU

OPTO-EDU A18.1828 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1018 Manual de usuario

OPTO-EDU

OPTO-EDU A14.1063 Manual de usuario

OPTO-EDU

OPTO-EDU XD Series Manual de usuario

OPTO-EDU

OPTO-EDU A22.1504 Series Manual de usuario

OPTO-EDU

OPTO-EDU A12.1095 Manual de usuario

OPTO-EDU

OPTO-EDU A10.1018 Manual de usuario

OPTO-EDU

OPTO-EDU A63.7080 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1091 Manual de usuario

OPTO-EDU

OPTO-EDU A16.2615-L Manual de usuario

OPTO-EDU

OPTO-EDU A15 0908 Series Manual de usuario

OPTO-EDU

OPTO-EDU A15.1016 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario