OPTO-EDU A10.1018 Manual de usuario

A10.1018

Professional Dark Field Microscope

Instruction Manual

Please read this manual carefully before use microscope!

Use Notices A10.1018

I、Safety Note

1. Carefully open the box, avoid the accessories, dropping to ground and being damaged.

2. Do keep the instrument out of direct sunlight, high temperature or humidity, dusty and easy

shaking environment. Make sure the stage is smooth, horizontal and firm enough.

3. When moving the instrument, please use two hands to grip with the two sides of the

microscope body.

4. If the bacterium solution or the water splash to the stage, objective or viewing tube, pull out the

power cord at once, and wipe up the microscope. Otherwise, the instrument will be damaged.

5. When running, the lamp house and nearby parts will be very hot. Please ensure there is

enough cooling room for them.

6. Make sure the instrument is earthed, to avoid lighting strike.

7. For safety, be sure the main switch is in “O”(off) state before replace the halogen lamp or the

fuse, then cut off the power, and do the operation after the lamp bulb and the lamp house

completely cool.

8. Check the input voltage: be sure the input voltage which signed in the back of the microscope is

consistent with the power supply voltage, or it will bring a serious damage to the instrument.

II、Maintenance

1. All the lenses have been well checked and adjusted. It is forbidden to disassemble them

yourself.

2. The nosepiece and coarse/fine focus unit have a compact and precise frame, please don’t

disassemble them as possible as you can.

3. Keep the instrument clean, wipe dust regularly, and be attention to avoid contaminating the

optical elements especially.

4. The contaminations on the prism, as finger mark and oil, could be gently wiped with a piece of soft

cloth or tissue paper, gauze which has been immersed in pure alcohol or xylene.

5. Don’t use organic solvent to wipe the non-optical elements, when you need to clean, use the

soft detergent, please.

6. When using, if the microscope is splash by liquid, cut off the power at once, and wipe up the

moisture.

7. Do not disassemble any parts of the microscope. That will affect the function or decline the

performance of the microscope.

8. Place the instrument in a cool, dry position. After using the microscope, remember to cover it

with dust helmet. Do wait for the lamp house cooling completely before cover.

1. Name of Components A10.1018

Installation A10.1018

Installation Diagram

The following figure shows the installation sequence of the components. The numbers in the figure

show the installation steps. Before installing, be sure every components is clean, do not touch

glass surface. Keep well with the supplied hexagon wrench. When changing the components, you

will need it again.

Video Port (Optional)

Eyepiece

Microscope Body

Trinocular Viewing Head

Nosepiece

Objective

Mechanical Stage

Lamp House

Microscope Body

Lamp House

Mechanical Stage Support Device

10×Wide Field Eyepiece

Infinite Plan Objective

Trinocular Viewing Unit

Video Port (optional)

①

②

③

④

⑤

⑥

2. Installation Steps A10.1018

2.1 Installing the Mechanical Stage Support Device

Before installing the device, be sure to adjust the coarse focus knob. Make the guide board (see

figure 1) down to the lowest position, so you can install the mechanical stage support device

easily.

Guide Board

Locking Block and Bolt

A10.1018

Hold on the mechanical stage support device (figure 2), place it from the top of the guide board

(figure 1), let the device (figure2) falling free until it reach the limit position. Use the hexagon

wrench screw down the locking block; make the stage support device (figure1) and the guide

board fixed together.

The mechanical stage have been adjusted horizontally and fixed together before leaving

factory. Do not disassembly unless necessary, that may affect the observation precision

of the instrument.

2-2-2 Installing the Trinocular Viewing

Unit

Insert the trinocular viewing unit (figure4) into

the microscope head (figure5), turn to a

proper position, then use the hexagon wrench

screw down the bolt to fix ( See figure 5 ).

2-2-3 Installing and Replacing the

Lamp (figure 6)

Please use the specified halogen Lamp

6V30W.

1．Hold to the bulb after you wrap it with gauze

or other protection materials, and then

deeply insert it into the lamp holder.

2. Replacing Lamp when using or soon after

When using, or soon after it is turned off, the

lamp, the lamp house and nearby parts will

be very hot and will cause serious burns.

Please turn the main switch on “O”(off), pull

out power plug, and make sure the bulb, the

lamp room and periphery are all cool. Then,

you can do your replacing.

Please insert the lamp gently, or it will be

damaged by excessive extrusion

Do not touch the Halogen bulb with your

bare hands. It will shorten the service life

or cause it to burst. If you leave finger

marks on the surface carelessly, clean it

with a dry soft cloth.

Bolt

Lamp House Bolt

A10.1018

2-2-4 Installing the Lamp House

Keep the bolt on the lamp house (figure 6) in

line with the jack on the back of the microscope

(like the show of figure 7), then pushing the

lamp holder into the illumination kits gently until

they are against each other (figure 8).

2-2-5 Installing the Objective

1. Adjusting the coarse focus knob until the

support device of the mechanical stage

reach its low limit position.

2. Wresting the lowest magnification objective

onto the nosepiece from the left or the right

side (figure 9), then push the nosepiece

clockwise, then place other objectives by

the sequence of low to high magnification

( figure 10).

Installing objective this way will make the

change of magnification to be easier while

in using.

Clean the objective regularly, the objective of

the inversed microscope is very sensitive to

dust.

When operating, use 10×magnification

objective to search specimen and focus

firstly, then replace with higher

magnification objective if necessary.

When replacing the objective, slowly

turning the nosepiece until you hear

“clicked”, that means the objective enter

the required position--the light path center.

Jack

Bolt

A10.1018

2-2-6 Installing the Eyepiece

Insert the eyepiece (figure 11) into the

eyepiece tube until they are against each

other. The result is showing in the figure

14.

2-2-7Installing the Video Port

(optional)

Insert the video port (figure 12) into the

trinocular unit (figure 13), then screw

down the bolt to fix it. The result is

showing in figure 14.

Eyepiece

3. Adjustment A10.1018

Diopter Ring

Left Fine Focus Knob

Left Coarse Focus Knob

Clocking Set

Condenser Focus Knob

Video Port (optional)

A10.1018

Note : the video port is optional.

Light Path Selector Lever

Video Port (optional)

Interpupillary Distance Indicator

Right Fine Focus Knob

Tension Adjustment

Collar

Right Coarse Focus Knob

Brightness Adjustment

Knob

Main Switch

Field Diaphragm

Swing out Condenser (with

Aperture Diaphragm)

PortraitAdjustment Knob

Lateral Adjustment Knob

Tabla de contenidos

Otros manuales de Microscopio de OPTO-EDU

OPTO-EDU

OPTO-EDU A41.1903 Manual de usuario

OPTO-EDU

OPTO-EDU A18.1825-LCD Manual de usuario

OPTO-EDU

OPTO-EDU A12.1303 Manual de usuario

OPTO-EDU

OPTO-EDU A11.1303 Series Manual de usuario

OPTO-EDU

OPTO-EDU A18.1831 Manual de usuario

OPTO-EDU

OPTO-EDU A23.1502 Series Manual de usuario

OPTO-EDU

OPTO-EDU A12.0910 Manual de usuario

OPTO-EDU

OPTO-EDU A13.2604-B Manual de usuario

OPTO-EDU

OPTO-EDU A12.1061 Manual de usuario

OPTO-EDU

OPTO-EDU A15.1016 Manual de usuario

OPTO-EDU

OPTO-EDU A15 0908 Series Manual de usuario

OPTO-EDU

OPTO-EDU A22.1201 Manual de usuario

OPTO-EDU

OPTO-EDU A15.2604 Manual de usuario

OPTO-EDU

OPTO-EDU A63.7080 Manual de usuario

OPTO-EDU

OPTO-EDU A63 .7080 Manual de usuario

OPTO-EDU

OPTO-EDU A59.4231 Manual de usuario

OPTO-EDU

OPTO-EDU A23.0910 Manual de usuario

OPTO-EDU

OPTO-EDU EX31 Series Manual de usuario

OPTO-EDU

OPTO-EDU A41.1950 Manual de usuario

OPTO-EDU

OPTO-EDU A22.3670 Series Manual de usuario

OPTO-EDU

OPTO-EDU A12.1010 Manual de usuario

OPTO-EDU

OPTO-EDU A23.3645 Series Manual de usuario

OPTO-EDU

OPTO-EDU A11.0214 Manual de usuario

OPTO-EDU

OPTO-EDU A18.1828 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario