Optika DM-5UP Manual de usuario

OPTIKA MICROSCOPES - ITALY

www.optikamicroscopes.com - [email protected]

Ver. 4.0.0

DM-5UP

OPERATION MANUAL

GUIDA UTENTE

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Page 2

INDEX

1.0 DESCRIPTION page 4

2.0 INTRODUCTION page 6

3.0 CONTENTS OF THE BOX page 6

4.0 UNPACKING AND ASSEMBLY page 6

5.0 USING THE MICROSCOPE page 7

6.0 USING THE VIDEO CAMERA page 7

7.0 MAINTENANCE page 8

8.0 TECHNICAL SPECIFICATIONS page 9

9.0 RECYCLING AND RECOVERY page 10

Page 3

This microscope is a scientific precision instrument designed to last for many years with a minimum of main-

tenance. It is built to high optical and mechanical standards and to withstand daily use.

Optika reminds you that this manual contains important information on safety and maintenance, and that it

must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this ma-nual.

Safety guidelines

This manual contains important information and warnings regarding safety about installation, use and

maintenance of the microscope. Please read this manual carefully before using the equipment. To

ensure safe use, the user must read and follow all instructions in this manual. OPTIKA products are

designed for safe use in normal operating conditions. The equipment and accessories described in

the manual are manufactured and tested according to industry standards for safety instrumentation

laboratory. Misuse can cause personal injury or damage to the instrument. Keep this manual at hand

close to the instrument, for an easy consultation.

Electrical safety

Before connecting the power cord to wall outlet, ensure that your mains voltage for your region corre-

sponds to the voltage supply of the instrument, and that the illuminator’s switch is in position OFF. The

user must observe the safety regulations in force in his region. The instrument is equipped with CE sa-

fety marking, in any case the user has full responsibility concerning the safe use of that instrument.

Warning/Caution symbols used in this manual

The user should be aware of safety aspects when using the instrument. Warning or hazard symbols

are shown below. These symbols are used in this manual.

The instructions on this symbol to avoid possible severe personal injuries.

Warning of use; the incorrect operation on the instrument can cause damages

to the person or instrument.

Possibility of electric shock.

Attention: high temperature surfaces. Avoid direct contact.

Technical notes or usage tips.

SAFETY GUIDELINES

Page 4

1.0 DESCRIPTION

EYEPIECE

OBSERVATION HEAD

WITH INTEGRATED

VIDEO CAMERA

NOSEPIECE

MAIN BODY

TENSION REGULATION

COARSE FOCUSING

KNOB

FINE FOCUSING

KNOB

MOVEABLE STAGE

SLIDE CLIP

OBJECTIVE

DM-5UP: FRONT VIEW

Page 5

1.0 DESCRIPTION

DM-5UP: REAR VIEW

USB-CABLE ATTACHMENT AND

POWER SUPPLY (4,8V DC)

CARRYING HANDLE

ON-OFF SWITCH

BRIGHTNESS

ADJUSTMENT

KNOB

LED LIGHT ILLUMINATOR

LOCK SCREW

POWER SUPPLY

(4,8V DC)

Page 6

2.0 INTRODUCTION

This microscope is a scientific precision instrument designed to last for many years with a minimum of main-

tenance. It is built to high optical and mechanical standards and to withstand daily use.

Optika reminds you that this manual contains important information on safety and maintenance, and that it

must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this manual.

Connect the mains plug into the socket at the base

Make sure, before you turn the illumination on, that the voltage selector is set to the mains voltage for

your region.

The power cord should be used only on network sockets equipped with adequate grounding.

Contact a technician to check the state of your electrical system. If there is no need to install additional

accessories, the instrument is now ready for use. Once positioned and installed with the necessary

components, the microscope is ready to be used. Your microscope is a laboratory instrument desi-

gned to last. Handle it always carefully and avoid abrupt vibrations or shocks. Always disconnect the

power cable from the microscope when not in use for long time, while you clean it or when you perform

any maintenance.

AVOID DISASSEMBLING THE INSTRUMENT

Do not disassemble the instrument. This entails the cancellation of the warranty and may cause

malfunction

• Microscope body with triple revolver (4,10,40x already mounted), monocular head with

digital output and mains cable already mounted

• CD OPMIAS

• USB software protection key

• USB cable

• Small screwdriver

• Wrench for regulation of focus tension

4.1 The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge of the

container and lift the top half of the container. Take some care to avoid that the optical items (objec-

tives and eyepieces) fall out and get damaged. Lift the microscope from the container and put it on a

stable desk.

4.2 Insert the eyepiece into the eye tube.

3.0 CONTENTS OF THE BOX

4.0 UNPACKING AND ASSEMBLY

Page 7

5.0 USING THE MICROSCOPE

5.1 Adjust the observation head

Loosen the lock-screw, turn the observation head to a comfortable position for observation, and then

lock the lock-screw.

5.2 Place the specimen on the stage

Lock the specimen slide on the mechanical stage using the slide clip. Ensure that the specimen is

centred over the stage opening by adjusting the coaxial knobs of the stage.

5.3 Lamp settings

The microscope is fitted with white LED illuminator. Before turning on the light, read the section 7.3

about electrical safety precautions. Insert the plug of the cable into the power socket and turn on the

switch on the back of the main body. Turn the brightness adjustment knob to a brightness suitable for

observation.

5.4 Focus adjustment

Rotate the coarse focusing knob to bring the slide into focus using an objective with a low magnifica-

tion. Adjust the fine focusing knob to get the image sharp and clear. Turn the tension regulation using

the wrench to get a suitable tension for the focus system. When the image is in focus, turn the nose-

piece to choose the objective you need.

6.0 USING THE VIDEO CAMERA

6.1 Installing the camera CD with the imaging software and drivers

The microscope is equipped with a digital camera incorporated in the head. To install the camera,

please follow these instructions:

1) Verify that your computer fulfils the system requirements (see Technical Specifications).

2) Insert the OPMIAS CD in your PC.

3) Open the CD and execute the file \opmias en vers 2.0 \ setup.exe.

4) Follow the instructions on the screen.

5) Insert the provided USB cable on the back of the microscope head and plug the other end of the cable

in a USB 2.0 port.

6) The camera will now be automatically identified and Windows hardware installation guide will start

automatically.

7) Repeat this process for the USB Software Dog that protects the software. Thus, plug in the USB Dog

in a free USB port.

8) The USB Dog will be automatically identified.

9) The camera can now be tested. Leave both the camera and the USB Dog connected to the PC (the

CD can be removed at this point) and run the shortcut that has been placed on the desktop.

10) Go to the “Help” menu and click on “Local Register”. “Register success!” will appear on the screen and

the software can now be used completely.

11) Press the video camera icon “Capture” for video capture mode.

12) Read the “Help” inside the software for further instructions.

Page 8

7.1 Microscopy environment

This microscope is recommended to be used in a clean, dry and shock free environment with a tem-

perature of 0-40°C and a maximum relative humidity of 85 % (non condensing). Use a dehumidifier if

needed.

7.2 To think about when and after using the microscope

- The microscope should always be kept vertically when moving it and be careful so that no moving

parts, such as the eyepieces, fall out.

- Never mishandle or impose unnecessary force on the microscope.

- Never attempt to service the microscope yourself.

- After use, turn off the light immediately, cover the microscope with the included dust-cover, and keep

it in a dry and clean place.

7.3 Electrical safety precautions

- Before plugging in the power cord with the supply, make sure that the supplying voltage of your re-

gion matches with the operation voltage of the equipment and that the lamp switch is in off-position.

- Do not turn the power on and off, off and on immediately as this will shorten the life span of the bulb

and may cause damage to the electrical system.

- Users should observe all safety regulations of the region. The equipment has acquired the CE safety

label. However, users do have full responsibility to use this equipment safely.

7.4 Cleaning the optics

- If the optical parts need to be cleaned try first to: use compressed air.

- If that is not sufficient: use a soft lint-free piece of cloth with water and a mild detergent.

- And as a final option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.

Note: ethanol and ether are highly flammable liquids. Do not use them near a heat source, near

sparks or near electric equipment. Use these chemicals in a well ventilated room.

- Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage

the optics.

- Do not disassemble objectives or eyepieces in attempt to clean them.

7.5 If you need to send the microscope to Optika for maintenance, please use the original packaging.

7.0 MAINTENANCE

Page 9

Head: Digital, monocular, 360° rotating, 45° inclined

Eyepieces: Wf10x/16mm

Nosepiece: Triple, reversed

Objectives: Achromatic 4x, 10x, 40x

Working stage: Rotating round stage, diameter: 90 mm, moving range 5 mm,

slide clips

Focusing system: Coarse and fine with different axis, with focus tension adjustment

Illumination: White led, non-rechargeable, with brightness control

Mains power: 4,8V DC

RESOLUTION: 640 x 480 pixels (480 kilo pixels)

Sensor: ¼”CMOS

Sensor imaging area: 4.12 mm x 3.07 mm

Data output:

(uncompressed video)

8 bit

Pixel size: 7.9 mm x 7.9 mm

Resolution & frame rate: 640 x 480

25 frames/second

Sensitivity: 2.3 V/Lux-sec

(550 nm)

Electronic shutter: 1/16-1/1600

White balance: Auto / Manual

S/n ratio: ≥52 dB

Dynamic range: ≥60 dB

Digital port: USB1.1 or USB2.0

Imaging software: OPMIAS (OPTIKA Micro Image Analysis Software), available in English

and Italian

System requirements: RAM: 256 MB (512 MB recommended)

Video card: Separate card (64 MB or higher)

Operating system: Windows XP, Windows Vista and Windows Seven 32

and 64bit.

8.1 Microscope

8.2 Video camera

8.0 TECHNICAL SPECIFICATIONS

Page 10

9.0 RECOVERY AND RECYCLING

Art.13 Dlsg 25 july 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating

to the reduction in the use of hazardous substances in electrical and electronic equipment and waste dispo-

sal.”

The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be

collected separately from other waste.

The separate collection of this equipment at the end of its lifetime is organized and managed by

the producer. The user will have to contact the manufacturer and follow the rules that he adop-

ted for end-of-life equipment collection. The collection of the equipment for recycling, treatment

and environmentally compatible disposal, helps to prevent possible adverse effects on the environ-

ment and health and promotes reuse and/or recycling of materials of the equipment. Improper dispo-

sal of the product involves the application of administrative penalties as provided by the laws in force.

Tabla de contenidos

Idiomas:

Otros manuales de Microscopio de Optika

Optika

Optika B-150 ALC Series Manual de usuario

Optika

Optika B-500Ti-2 Manual de usuario

Optika

Optika B-500BSp Manual de usuario

Optika

Optika B-1000 POL Manual de usuario

Optika

Optika XDS-3FL Manual de usuario

Optika

Optika B-350 Manual de usuario

Optika

Optika XC-100L Manual de usuario

Optika

Optika SZN Series Manual de usuario

Optika

Optika B-1000 POL Manual de usuario

Optika

Optika B-600 Manual de instalación

Optika

Optika B-1000 Series Manual de usuario

Optika

Optika B-60 Series Manual de usuario

Optika

Optika STEREO Manual de instrucciones

Optika

Optika SZM Manual de usuario

Optika

Optika OPTIKAM FAST3 Series Manual de usuario

Optika

Optika B-180 Manual de usuario

Optika

Optika B-510 Series Manual de usuario

Optika

Optika OPTIStar OS-SZ1 Manual de usuario

Optika

Optika INSPECTION SYSTEMS Series Manual de usuario

Optika

Optika B-510 Series Manual de usuario

Optika

Optika ECOVISION Series Manual de usuario

Optika

Optika IM Series Manual de usuario

Optika

Optika B-1000Ti-2 Manual de usuario

Optika

Optika XZ-2 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario