Optika B-1000 POL Manual de usuario

Version: 1

Issued: 01, 12, 2015

Model

B-1000MET

B-1000 Series

INSTRUCTION MANUAL

Page 2

Table of Contents

Warning

Symbols and conventions

Safety Information

Intended use

List of accessories and spare parts

Overview

Unpacking

Assembling

Using the microscope

Maintenance

Troubleshooting

Equipment disposal

Page 3

Warning

This microscope is a scientic precision instrument designed to last for many years with a minimum of mainte-

nance. It is built to high optical and mechanical standards and to withstand daily use. We remind you that this

manual contains important information on safety and maintenance, and that it must therefore be made acces-

sible to the instrument users. We decline any responsibility deriving from incorrect instrument use uses that does

not comply with this manual.

Symbols and conventions

The following chart is an illustrated glossary of the symbols that are used in this manual.

CAUTION

This symbol indicates a potential risk and alerts you to proceed with caution.

ELECTRICAL SHOCK

This symbol indicates a risk of electrical shock.

Safety Information

Avoiding Electrical Shock

Before plugging in the power supply, make sure that the supplying voltage of your region matches with the

operation voltage of the equipment and that the lamp switch is in off position. Users should observe all safety

regulations of the region. The equipment has acquired the CE safety label. However, users have full responsibil-

ity to use this equipment safely. Please follow the guidelines below, and read this manual in its entirety to ensure

safe operation of the unit.

Intended use

For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.

Page 4

List of accessories and spare parts

CAT. NO. DESCRIPTION

M-005 Micrometric slide, 26x76mm, range 1mm, div. 0,01mm

M-613 Polarizing set (lters only)

M-615 Lambda lter for polarizing set

M-617.1N Phase contrast set with IOS PLAN objective 40x

M-781 WF10x/22mm micrometer eyepiece (10mm, 0.1mm div.)

CL-35 Halogen Lamp 24V 100W (only for metallurgical attachment M-1035)

M-690 Eyecup (pair)

M-619 Photo adapter for REFLEX camera with FULL FRAME sensor

M-173 Photo adapter for APS-C and Full Frame Reex cameras

M-699 Universal adapter for M-114, M-116, M-173 and eyepiece cameras

M-620 C-Mount adapter for 1/3” sensor.

M-620.1 C-Mount adapter for 1/2” sensor.

M-114 C-Mount adapter for 1/2” sensor.

M-116 C-Mount adapter for 2/3” sensor.

Page 5

Overview

STAGE LOCK

KNOB

COARSE

FOCUSING

KNOB

NOSEPIECE

DIOPTRIC

ADJUSTMENT

RING

PHOTO PORT

EYEPIECE

CONDENSER

CENTERING

KNOBS

APERTURE

DIAPHRAGM

APERTURE

DIAPHRAGM

FIELD DIAPHRAGM

FINE FOCUSING

KNOB

EXTERNAL

POWER

SUPPLY

OBJECTIVE

STAGE

INCIDENT

ILLUMINATION

ATTACHMENT

Page 6

Put the microscope stand on a

solid table.

First insert the incident illu-

mination attachment, using

the 2,5mm Allen wrench to

tighten the screw. All screws

are already inserted into each

threaded hole.

(Fig.1)

Unpacking

The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge of the container

and lift the top half of the container. Take some care to avoid that the optical items (objectives and eyepieces)

fall out and get damaged. Using both hands (one around the arm and one around the base), lift the microscope

from the container and put it on a stable desk.

Assembling

Once you open the box, these are the microscope’s components:

①Condenser

② Optical head

③ Main body

④ Eyepieces

⑤ Polarizer/Analyzer

⑥ Stage

⑦ Objectives

⑧ Extension Tube

⑨ Lamp house

⑩ External power supply

⑪ Incident illumination attachment

①

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

Fig.1

Page 7

Insert the condenser under

the stage: push until it is well

inserted into its holder (under

the condenser there is a pin

that must fully enter the guide

of the holder). (Fig.6)

Insert the lamp house into the

extension tube, then use an

allen wrench to x it. (Fig. 4)

AFTER INSERTING THE

CONDENSER, TIGHTEN

THIS SCREW

Insert the optical head above

the attachment using the other

3mm Allen wrench to tighten

the screw. (Fig.2)

Insert both eyepieces into

the tubes of the optical head.

(Fig.5)

Insert the extension tube

on the rear of the incident

illumination attachment, then

use an allen wrench to x it.

(Fig.3)

Fig.2

Fig.5

Fig.3

Fig.6

Fig.4

Page 8

Insert the power supply cable

for incident light. (Fig.10)

Connect the cable to the

external power supply. (Fig.9)

Insert the power supply jack

on the connector at the rear.

(Fig.11)

Fig.9

Fig.10

Fig.11

Screw each objective into the

thread of the nosepiece, in

order of magnication. (Fig.8)

Fig.8

Mount the stage: lower the

support using the coarse

focus knob, then place the

stage and rmly tighten the

lock screw. (Fig.7)

Fig.7

Page 9

B-1000 illumination can be managed through

the keyboard placed on the left of the stand:

1) ON-OFF: press this button to turn on or off

the LED illuminator.

2) BOOST: press this button in order to incre-

ase the brightness (useful for high-magnica-

tion objectives or very opaque specimens).

2) AUTO-OFF: if you want the illuminator to

switch off automatically, press this button until

15, 30 or 60 minutes delay is set. After this

period of time, the light will turn off. You have

to press the ON-OFF button to turn it on again.

(Fig.12)

In order to activate the illuminator, insert the

plug of the external power supply into the

socket and turn on the main switch on the side

of the main body. Press the ON-OFF button on

the control keyboard and turn the brightness

adjustment knob to a brightness suitable for

observation. (Fig.13)

Do not enable boost mode while observing with

low magnication objectives (4x, 10x) with fully

open diaphgram: the high brightness may hurt

user’s eyes.

Control keyboard

LED settings

Preliminary settings

1) ON-OFF

3) AUTO-OFF

2) BOOST

MAIN

SWITCH

• The eld diaphragm is

fully open. (Fig.14)

• The aperture diaphragm

is fully open. (Fig.15)

• No lter is inserted under

the observation head.

Using the microscope

Fig.12

Fig.13

Fig.14

Fig.15

Before trying to focus the

sample, ensure that:

Page 10

Loosen the lock-screw, turn

the observation head to

a comfortable position for

observation, and then lock the

lock-screw. (Fig.18)

Hold the right and left parts of

the observation head using

both hands and adjust the

interpupillary distance by

turning the two parts until one

circle of light can be seen.

(Fig.19)

Adjust the observation

head

Adjust interpupillary

distance

• The selector on metal-

lurgical attachment is in

“BF” (Brighteld position)

(Fig.16)

• Photo port closed

(lever on observation

head fully in).

• (If you use 5X objective)

Swing out lens of the

condeser in OUT position.

(Fig.17)

Fig.16

Fig.17

Fig.18

Fig.19

Otros manuales para B-1000 POL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Microscopio de Optika

Optika

Optika B-180 Manual de usuario

Optika

Optika B-150 ALC Series Manual de usuario

Optika

Optika IM Series Manual de usuario

Optika

Optika B-290 Manual de usuario

Optika

Optika STEREO Manual de instrucciones

Optika

Optika B-380 Series Manual de usuario

Optika

Optika B-190 Manual de usuario

Optika

Optika B-600 Manual de instalación

Optika

Optika OPTIGEM Manual de usuario

Optika

Optika B-510 Series Manual de usuario

Optika

Optika B-1000 Series Manual de usuario

Optika

Optika B-600 MET Manual de usuario

Optika

Optika B-380 Series Manual de usuario

Optika

Optika B-1000 POL Manual de usuario

Optika

Optika B-500BSp Manual de usuario

Optika

Optika B-190 Manual de usuario

Optika

Optika B-50 Manual de usuario

Optika

Optika B-810 Series Manual de usuario

Optika

Optika XDS-3FL Manual de usuario

Optika

Optika IM Series Manual de usuario

Optika

Optika B-500POL Manual de usuario

Optika

Optika B-150POL-M Manual de usuario

Optika

Optika B-150 Series Manual de usuario

Optika

Optika B-500TiFL Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario