olympia electronics WATERPROOF POWER LIGHT Series Manual de usuario
923021011_09_004
Page 1 from 4
GENERAL
These luminaires are used in places
where emergency luminaires are needed.
Each luminaire must be permanently
co nn ec te d t o m ai ns po we r s up pl y.
Internally, the product consists of 2
subsystems, 1 for each lamp. Each
subsystem contains 2 batteries that are
c h a r g e d a n d d i s c h a r g e d a n d a r e
i n d e p e n d e n t f r o m t h e o t h e r .
Due to this, each lamp lights with its own
b a t t eries and th u s d u r i n g a d e e p
discharge will go OFF at a slightly different
instance compared to the other lamp.
In the event of a power failure, the
luminaire will automatically light both
lamps. When the mains power supply is
restored the luminaire returns to normal
charging operation.
The perimeter of the TEST button contains
a green charge indicator. When the unit is
connected to the power supply and the
batteries are also connected, the green
indicator blinks to show that the batteries
are charging but are not fully charged.
When the batteries are fully charged then
the indicator stays ON continuously. On
every press of the TEST button and for as
long as the test is conducted, the indicator
w i l l b e O F F. I f t h e b a t t e r i e s a r e
disconnected the indicator will also be
turned OFF. In order to do a complete
duration test please be sure that the
indicator is continuously ON. If it is blinking
it is a sign of a power failure and that the
batteries are not fully charged. Let the
batteries charge until the indicator stops
blinking and then conduct the duration test.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personnel only.
2. The device must be connected to the
mains power supply through a fuse
dependent by the total amount of the line’s
power load.
3. It is suggested to check every 6 months
the minimum autononous duration by
disconnecting the mains power supply.
Count the time that the lamps light and in
case of less time than the minimum
autonomous duration the batteries must be
r eplac e d . I f t he mea s u r e d t ime is
considerably less than the minimum
autonomous duration contact the installer.
Congratulations for your selection to buy this product.
Olympia Electronics - European manufacturers.
WATERPROOF POWER LIGHT SERIES, NON MAINTAINED EMERGENCY LUMINAIRE
GR-21/Η3
TECHNICAL CHARACTERISTICS
220-240V AC/50-60Hz
3 ώρες
24 ώρες
From overcharge and deep discharge
IP 65
4x12V/7Ah
1380lm
2x55W (halogen)
38W/ 47VA
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
Electrostatically painted metal plate
3 years (1 year for the lamps and the battery)
15.71 Kgr.
405 x 130 x 500 mm
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Pb)
CHARGING TIME
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
923021011_09_004
Page 2 from 4
The replacement of the battery and the
light source must be done using parts of
the same type, by the manufacturer or by
a competent person.
4. In case of inactive use for a period
greater than 2 months, disconnect the
battery by pulling out the battery’s
connector.
5. I s not allowed to discard batteries t i
in to common trash bins, they
must be discarded only in battery
recycling points. Do not incinerate.
INSTALLATION
To install the luminaire follow the
installation instructions οn pages 3 and 4.
Battery replacement.
It can be done only by a competent
p e r s o n a n d a f t e r t h e m a i n s
interruption.
1. In order to remove the front cover,
unscrew the 4 retaining screws (page 3).
2. Unscrew the screws and remove the
retaining bracket (page 4) (2A).
3. Disconnect the cables and remove the
old batteries.
4. Connect the new batteries with the
same type (step 3 of the installation
procedure) and place them in the position
of the old batteries. Install the retaining
bracket and fasten the screws (2A).
5. Follow the step 7 of the installation
procedure and power the device.
LABELING EXPLANATION:
X: Self contained
0: Non maintained (*)
A: Including test device
180: 3 hour duration
(*) Non Maintained operation: The
luminaire lights its illumination source,
only in power supply’s failure.
Maintained operation: The luminaire lights
its illumination source, when it is powered
by the mains power supply or not.
WARRANTY
Olympia Electronics guarantees the quality,
condition and operation of the goods. The
period of warranty is specified in the official
catalogue of Olympia Electronics and also in
the technical leaflet, which accompanies each
product. This warranty ceases to exist if the
buyer does not follow the technical instructions
included in official documents given by Olympia
Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done
by a third party, unless Olympia Electronics has
fully agreed to them in writing. Products that
have been damaged can be returned to the
premises of our company for repair or
replacement, as long as the warranty period is
valid.
Olympia Electronics reserves the right to repair
or to replace the returned goods and to or not
charge the buyer depending on the reason of
defection. Olympia Electronics reserves the
right to charge or not the buyer the
transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
Page 3 from 4926021003_09_004
INSTALLATION INSTRUCTIONS
1. In order to remove the front cover, unscrew the 4 retaining screws.
2. Mark the 4 points in the installation area. After installing the plastic plugs in the wall mount
the luminaire with the mounting screws.
3. Make sure that the battery’s cables are connected to the respective poles. Black cable to (-)
pole and red cable to (+) pole.
4. Always use in any case round mains cable, with diameter of 6-9mm (H05RN-F
type 3x1mm² or any other type, at least equal to it’s mechanical and electrical
properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is
important to ensure the tightness isolation IP 65). Install the cable gland, pass the round
cable through and tighten it all the way.
5. Connect the wires to the terminal blocks L for live wire, Ν for neutral and for the
ground.
6. Battery protection fuses. When the spot lights are not functional in emergency mode, check
these fuses and replace them if necessary (one fuse corresponds to each spot light).
7. Refit with care the front cover, by fastening the 4 retaining screws (tightening torque 1Nm).
mains’ power
supply cable
entry
4
TEST button
and
charge indication
retaining
screws
front cover
1
1
Minimum distance from lighted objects.
Front cover retaining screw
Mettalic
washer
Rubber
washer
Mounting screw
Page 4 from 4923021011_09_004
NOTE!!
After finishing the installation you must power the luminaire at least for 24 hours
for battery charging to perform the nominal autonomy.
5
Charge indication
2 6
L N
4
3
TEST button
2A
Este manual sirve para los siguientes modelos
1
Otros manuales de Linterna de olympia electronics
olympia electronics
olympia electronics GRL-38/90/M Manual de usuario
olympia electronics
olympia electronics Slim Light Series Manual de usuario
olympia electronics
olympia electronics GR-940/15L/MAR Manual de usuario
olympia electronics
olympia electronics KLIN-20/ST/ADR Manual de usuario
olympia electronics
olympia electronics BAU LIGHT Series Manual de usuario
olympia electronics
olympia electronics POWER LIGHT Series Manual de usuario
olympia electronics
olympia electronics GR-1935/15L Manual de usuario
olympia electronics
olympia electronics GR-427/12L Manual de usuario
olympia electronics
olympia electronics POWER LIGHT Series Manual de usuario
olympia electronics
olympia electronics GR-938/15L Manual de usuario
olympia electronics
olympia electronics OLY-500 Manual de usuario
olympia electronics
olympia electronics GRL-37/90/WP Manual de usuario
olympia electronics
olympia electronics GR-108/12L/90 Manual de usuario
olympia electronics
olympia electronics Classic Light Series Manual de usuario
olympia electronics
olympia electronics GRL-37/90/ADR Manual de usuario
olympia electronics
olympia electronics GR-427/12L/MAR Manual de usuario
olympia electronics
olympia electronics GR-490/ADR Manual de usuario
olympia electronics
olympia electronics GR-939/30L/LT Manual de usuario
olympia electronics
olympia electronics CLASSIC LIGHT Series Manual de usuario
olympia electronics
olympia electronics GR-290 Manual de usuario
