Olympia electronics GR-1935/15L Manual de usuario

Page 1 from 4923193601_09_008

GENERAL

T h e s e l u m i n a i r e s a r e u s e d w h e r e

emergency light is needed. Each luminaire

must be permanently connected to the

mains power supply. In normal operation

the battery is charging, the green LED and

2 yellow LED’s light in non-maintained

operation. The green LED and the LED

strip light in maintained operation. In case

of a mains power supply failure the

lum i n a i r e wil l l i g h t the L E D s t r ip

automatically in emergency mode. When

the mains power supply is restored the

device turns to normal operation.

Non maintained / maintained operation

There is an option to select the non-

maintained or maintained operation by

placing the jumper to the appropriate place

(page 2).

INSTALLATION

To install the luminaire follow the installation

instructions on page 2.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personnel only.

2. The luminaire must be connected to the

mai ns po wer supp ly th roug h a fu se

dependent on the total amount of the line’s

power load.

3. It is suggested to check every month the

indication LED for battery charging, and by

placing the test card (page 3) an (A-1900)

operation test is initiated, to check the

emergency cirquit. The illumination source

should light as long as the card is present.

In the opposite condition contact the

installer.

4. It is suggested to check every 6 months

the minimum autononous duration by

disconnecting the mains power supply.

Count the time that the led strip lights and

in case of less time than the minimum

autonomous duration the battery must be

r e p l a c e d . I f t h e m e a s u r e d t i m e i s

considerably less than the minimum

autonomous duration contact the installer.

In case of battery or led strip replacement,

WATERPROOF NON MAINTAINED / MAINTAINED EMERGENCY LUMINAIRES WITH WHITE LEDs

220-240V AC/50-60Hz

3.3W/3.5VA

TECHNICAL CHARACTERISTICS (for LED MODULE Specs see page 4)

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Ni-Cd)

CHARGING TIME

INDICATIONS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

ILLUMINATION (MAINS / EMERGENCY)

ILLUMINATION SOURCE

90min

24h

Charge indication LED

From overcharge and deep discharge

IP65

3.6V/3Ah

40lm / 210lm

30 white LEDs

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

5 to 40 C

Up to 95%

3 years (1 year for the battery)

810gr.

3.1W/3.3VA

3.6V/0.6Ah

40lm / 105lm

15 white LEDs

180min

4.5W/4.8VA3.4W/3.6VA

3.6V/1.5Ah

40lm / 105lm

30 white LEDs

40lm / 210lm

15 white LEDs

630gr. 710gr.

313 x 118 x 66 mm

Bayblend FR3010, transparent polycarbonate

Thank you for your trust in our products.

Olympia Electronics - European manufacturer.

GR-1935/15L GR-1936/15L GR-1936/30LGR-1935/30L

Page 2 from 4

these must be replaced by parts of the

same type, by the manufacturer or by a

competent person.

5. In case of inactive use for a period

greater than 2 months, disconnect the

battery by p u l l i n g o u t the battery’s

connector.

6. I s not allowed to discard batteries in t i

to common trash bins, they must be

discarded only in battery recycling

points. Do not incinerate.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated

*90: 1.5 hour duration

180: 3 hours duration

(*) Maintained operation: The luminaire

lights its illumination source, when it is

Non Maintained operation: The luminaire

lights its illumination source, only in power

supply’s failure.

Note!! The installer should fill in, on the

specification label, the letter G if the luminaire

is used as a safety sign.

NOTE!! After finishing the installation

you must power the luminaire at least for

24 hours for battery charging to perform

the nominal autonomy.

Battery replacement

It can be done only by a competent

person and after the mains interruption.

1. Follow the step 1 of the installation

insrtuctions and remove the diffusor.

2. Remove the reflector (step 1 of the

installation instructions).

3. Remove the old battery and place a new

on of the same type and characteristics.

4. Replace the removed parts (previous

steps 1, 2).

The light source contained in this

luminaire shall only be replaced by

the manufacturer, or his agent, or a

similar qualified person.

NOTE! The light source is non-user

replaceable.

WARRANTY

Olympia Electronics guarantees the quality,

condition and operation of the goods. The

period of warranty is specified in the official

catalogue of Olympia Electronics and also

in the technical leaflet, which accompanies

each product. This warranty ceases to exist

if the buyer does not follow the technical

instructions included in official documents

given by Olympia Electronics or if the buyer

modifies the goods provided or has any

repairs or re-setting done by a third party,

unless Olympia Electronics has fully agreed

to them in writing. Products that have been

damaged can be returned to the premises

of our company for repair or replacement,

as long as the warranty period is valid.

Olympia Electronics reserves the right to

repair or to replace the returned goods and

to or not charge the buyer depending on the

reason of defection. Olympia Electronics

reserves the right to charge or not the buyer

the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60061 Greece

www.olympia-electronics.gr

[email protected]

923193601_09_008

X1 81 0A G

Page 2 from 3923193601_09_008

Indications

Charge

NON MAINTAINED/MAINTAINED OPERATION

JUMPER SELECTION

You can choose the luminaire’s operation. When the

jumper is installed (by default) in the middle and left pins

maintained operation is selected.

When the jumper is installed in the middle and right pins

non-maintained operation is selected.

Maintained

operation

Non Maintained

operation

INSTALLATION INSTRUCTIONS FOR WALL OR CEILING MOUNTING

1 Unclip the plastic latches with a flat blade screwdriver, unfasten the 2 screws (not all the

way, step 8 B) and remove the diffusor. Place simultaneously 2 flat blade screwdrivers to

the recesses and pull up gently the reflector.

2 Install the base plastic (with the included mounting screws and plugs). WARNING!! To

preserve the ΙΡ65 rating, fit the screws with the metallic washers and plastic rings

which are included.

3 Always use in any case round mains cable, with external diameter of 5-10mm

(H05RN-F type 2x1mm² or any other type, at least equal to it’s mechanical and

electrical properties).

ATTENTION!! The cable must not be deformed in any way (This requirement is

important to ensure the ΙΡ65 rating). Install the gasket and make a hole in the center by

using a small screwdriver. Pass the round cable through the gasket. Install the second

included gasket in to the unused hole.

4 Place the battery’s connector to the corresponding connector on the P.C.B.

5 Connect the mains cables to the respective terminal block Ν for neutral, L for live wire.

6 Install the included tie to fasten securely the power cables.

7 Refit the reflector (mind the holes of the indications).

8 Finally place the diffusor (mind the holes of the indications). Attention!! First the plastic

latches (A) must be secured (click sound) and then fasten the 2 screws (B)

(tightening torque 1.2 Nm).

Mains connection

A-1900

Test card

Manual TEST with the A-1900 Test

card (not included). This card is

available only after request. In order to

test the device, you must place the

card on the side of the indications.

This operation lasts as long as the

card is present.

Page 4 from 4923193601_09_008

LED MODULE CHARACTERISTICS

Olympia Electronics S.A.

Non reversible connection between main pcb and led module

2.9-3.6 V DC

980mw 1960mw

2502159/15L 2502159/30L

GR-1935/15L

GR-1936/15L

GR-1935/30L

GR-1936/30L

47 °C max. across the board

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Este manual sirve para los siguientes modelos

Otros manuales de Linterna de olympia electronics

olympia electronics

olympia electronics GR-940/15L/MAR Manual de usuario

olympia electronics

olympia electronics GR-290/WP Manual de usuario

olympia electronics

olympia electronics Classic Light Series Manual de usuario

olympia electronics

olympia electronics WEATHER LIGHT Series Manual de usuario

olympia electronics

olympia electronics GR-2110 Manual de usuario

olympia electronics

olympia electronics GR-108/12L/90 Manual de usuario

olympia electronics

olympia electronics OLY-500 Manual de usuario

olympia electronics

olympia electronics GR-427/12L Manual de usuario

olympia electronics

olympia electronics GR-427/12L/MAR Manual de usuario

olympia electronics

olympia electronics GR-938/15L Manual de usuario

olympia electronics

olympia electronics POWER LIGHT Series Manual de usuario

olympia electronics

olympia electronics GR-796/ST/DUO/ADR Manual de usuario

olympia electronics

olympia electronics GR-490/WP Manual de usuario

olympia electronics

olympia electronics POWER LIGHT Series Manual de usuario

olympia electronics

olympia electronics GR-292/M/HL Manual de usuario

olympia electronics

olympia electronics Power Light Series Manual del operador

olympia electronics

olympia electronics GR-8/leds Manual de usuario

olympia electronics

olympia electronics BAU LIGHT Series Manual de usuario

olympia electronics

olympia electronics LLB-26/90 Manual de usuario

olympia electronics

olympia electronics GR-939/30L/LT Manual de usuario

olympia electronics

olympia electronics KLIN-20/ST Manual de usuario

olympia electronics

olympia electronics BAU LIGHT Series Manual de usuario

olympia electronics

olympia electronics OLY-1004/WP/ADR Manual de usuario

olympia electronics

olympia electronics Slim Light Series Manual de usuario

Manuales populares de Linterna de otras marcas

KYOWA

KYOWA KW-9114 Manual de usuario

Stahl

Stahl ECOLUX 6610 Series Manual de usuario

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manual de usuario

PRG

PRG VARI LITE VL5 Manual de usuario

Raytec

Raytec VARIO2 series Manual de usuario

ENSA

ENSA LEDBT18WS2 Manual de usuario

LUG

LUG OFFICE LB LED N/T Manual de usuario

GE Wallighter 250 Manual de usuario

Draper

Draper RLEDL19/B Manual de usuario

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manual de usuario

Panasonic

Panasonic EY3741B57 Manual de usuario

Clas Ohlson

Clas Ohlson LCC8T Manual de usuario

Coolon

Coolon WDN-140 Manual de usuario

Holiday Travel

Holiday Travel 834873 Manual de usuario

BEGA

BEGA 84 036 Manual de usuario

BEGA

BEGA 33 596 Manual de usuario

Dale Tiffany

Dale Tiffany GT701162 Manual de usuario

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manual de usuario

olympia electronics GR-1935/15L Manual de usuario

Manuales populares de Linterna de otras marcas