MRC WBH-060N Manual de usuario

3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529

[email protected]

Digital Bath

With Internal/External circulation

WBH-060N

3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529

[email protected]

General Remarks

•Do not turn on the bath without liquid.

•Do not fill oil or any other material that is not water.

•Distilled water should be filled, not tap water, to avoid scale

•Liquid must be filled at least 90% of the tank volume.

•Do not overfill liquids, that can spill out during operation.

•Attention should be paid to the level of the liquid especially in

external working condition and to fill the liquid if the water level is

not enough.

•Make sure that before operating, the lid is placed and closed tightly.

•Do not clean the bath or internal container with acids or corrosive

substances.

•Do not allow foreign objects to enter the internal tank and block the

circulating mechanism and circulation motor

•Make sure to use distilled water, not tap water, to prevent from scale

to buildup in the heating element, circulating mechanism and all

components of the system.

•Do not block the ventilation openings of the control system.

•Do not spill liquids or wet the controlling system to avoid shock

hazard and damage to the bath.

General Description

Front View:

3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529

[email protected]

Rear View:

Digital Controller

3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529

[email protected]

Working instructions and temperature adjustment:

1. Connect pipes to the inlet and outlet connectors of the appliance

according to use (external or internal circulation).

2. In external working mode, pay attention to the flow direction from

the connectors and connect the pipe accordingly.

3. Fill liquid at least 90% of the tank volume.

4. Pay attention to the level of the liquid especially in the external

working condition and fill the liquid if needed.

5. Plug the power cord into the 230VAC power supply and turn on the

unit with the main power button.

6. Adjust the desired temperature with the "Up key" button on the

controller and confirm with the "scroll key" button.

Important note:

Do not enter the internal configurations of the controller unnecessarily and

do not change values other than the required temperature values.

Tabla de contenidos

Otros manuales de Equipo de laboratorio de MRC

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario