MRC CENVCC-3 Manual de usuario

CENVCC-3

Table Vacuum Centrifugal concentrator

Instruction & Using Manual

Please read this manual carefully before use

3, Hagavish st. Israel 58817 Tel: 972 35595252, Fax: 972 3 5594529

[email protected]

MRC.8.22

Content

Ⅰ、FEATURES AND USES ..............................................................................1

Ⅱ、WORKING PRINCIPLE ............................................................................2

Ⅲ、VACUUM CONCENTRATOR SPECIFICATION ..................................2

Ⅳ、ROTOR SPECIFICATION ........................................................................ 4

Ⅴ、PRECAUTION .............................................................................................5

Ⅵ、APPEARANCE AND STRUCTURE ........................................................ 6

Ⅶ、WORKING PROCEDURE ........................................................................ 7

VIII、TROUBLES & SOLUTIONS ................................................................. 8

IX、INSTALLATION......................................................................................9

X、MAINTENANCE....................................................................................... 10

XI、WARRANTY...........................................................................................11

XII、CERTIFICATE OF CONFORMITY..................................................12

XIII、PACKING LIST...................................................................................13

1/17

一、Features and Uses

CENVCC-3 is a microcomputer-controlled desktop vacuum concentrator. made by full steel body. the

surface is spray-coated, with good rigidity and high strength. It has novel shape, beautiful appearance, low

noise, rising temperature slowly, safety and reliability etc

This machine use frequency conversion motor. stable speed and maintenance free.Adpot high-quality

solenoid valve and fully closed microporous filter ensure smooth and safe return air. LCD display

temperature, PID algorithm temperature control, highly temperature accuracy. adopts 304 stainless steel

inner cavity, transparent high-strength lid and aluminum rotor. with strong corrosion resistance, not easy to

scratch,has a long service life

Ⅱ、Working principle

The vacuum concentrator is a method in which the sample is continuously pumped by a

vacuum pump while being centrifuged, or even close to vacuum, so that the solvent in the

sample is quickly evaporated, the sample system is rapidly concentrated or dried, and the cold

trap and the filtration method can be effectively used,which collected evaporated solvent. This

model is suitable for RNA/DNA in the fields of molecular biology, biochemistry, genetics,

analytical chemistry, quality control, etc., as well as protein concentration or drying. The

sample after centrifugation and concentration can be conveniently used for various qualitative

and analysis of chemistry, biochemistry, bioanalysis, immunoscreening and instrumental

analysis.

Ⅲ、Vacuum Concentrator Specification

Max RPM：1800r/min

Max capacity：62*1.5mm

Max RCF： 409×g

Speed accuracy：±20r/min

Time control：1～99min59s

Time control accuracy：±1S

Temperature stability range：Room temp～+60℃

Temperature Accuracy：±2℃

Ultimate vacuum: -0.1Mpa

2/17

Noise：≤50dB

Power：AC220V±10% 50Hz 10A

Machine size：430 mm×400 mm×330 mm (L×W×H)

Net Weight：35Kg

Ⅳ、Rotor Specification

Rotor

Number

Capacity

Max Speed

Max RCF

Angle rotor

No.1

62×1.5ml

1800r/min

409×g

No.2

135×0.5ml

1800r/min

273×g

Ⅴ、PRECAUTION

1. In order to safety working and correct centrifuging, please take the machine in a solid,

shockproof and horizontal table, please ensure the four feet equal force.

2. Before using, please move out the foreign body; check the rotor is correctly installed in the

rotor seat, please ensure the ro

3. tor and motor shaft with very good connection.

4. Set the speed strictly under the speed range allows, It is strictly prohibit to work

over-speed.

5. No unbalance working, centrifuge tube must be placed symmetrically, no single tube

working, the tube solution must be uniform to ensure balanced operation.

6. No high-speed working without rotor.

7. Remove the rotor must use the special handle which together with the machine or use

non-metallic tools gently tap the rotor first, repeated until the shock between the rotor and the

motor shaft connection. It is strictly prohibited to release the screw directly after the hard pull

up, so as not to damage the motor's flexible support.

8. Before using the rotor and centrifuge tube to check whether there are cracks, corrosion

traces and aging phenomena, if necessary to immediately replace, it is strictly prohibited to

use the rotor with crack or corrosion.

3/17

9. Check whether the external power supply meets the requirements, the instrument is

reliable grounding.

10. No moving and No lid-open during the centrifuge running, Do not open the lid when the

motor and rotor are not completely stopped.

11. The instrument or rotor disabled for three month, please running at low speed 10min, then

allow to work on high speed.

12. To prevent damage to the instrument and personal safety, No mixed using other company

Rotors.

13. To prevent the machine and spare parts corrode, Do Not place a container with liquid on

the instrument.

14. Please clean the machine and close the power switch and power plug after using.

Ⅵ、Appearance and structure

1、Concentrator appearance

2、Display Panel

4/17

1.Information window 2、Speed window 3、RCF window 4、Time

window 5、Rotor no. 6、Acceleration gear 7、Deceleration gear 8、

Program group number 9 、Setting key 10 、increasing key 11 、

instantaneous centrifugal key 12、Running indicator 13、Start key 14、

Confirmation key 15、Reduction key 16、Speed/Centrifugal Force Mode

Switching Key 17、Stop indicator 18、Stop key/open key

Ⅶ、Working procedure

1) the centrifuge placed on the platform, visual to balance, shake and check whether the

centrifuge placed smoothly.

2) confirm the placement is stable, turn on the power, press the power switch, press the "stop

/ open" button, the lid can be opened.

3) Open the lid, the selected rotor gently placed on the motor shaft, screw on the screw so

that the rotor and the motor shaft tightly connected together (Note: it should be careful

and gentle, to avoid shaking and pull up and down, so as not to Damage the motor

support), and then put the tube set or adapter on the rotor, complete gently turn the rotor,

the rotor should be flexible rotation, Tube set (adapter) on the rotor should be tilted freely,

no block and rub Touch the phenomenon.

4) Put the tube filled with the same amount of test solution symmetrical into the tube set to

ensure that the rotor balance operation.

5) close the lid and check whether it has been locked (closed gently lift the lid, the lid is not

open. If the lid is not closed, press the "Start", the "time display" window will display "

E3 ").

6) set the rotor number, speed, time and other operating parameters.

(1)Set the speed: press the "Set" key, move the cursor to the "speed setting" position,

when the speed digital flicker, that is, enter the speed setting, then press the "increase

key" or "reduce key" to set the speed of this operation, after setting, press the

confirmation key to confirm the parameters.

Special reminder: The horizontal rotors and different adapters of this machine have their

own rotor numbers and maximum speed limits. Users must strictly observe the speed

limits of the rotor parameters when setting the speed parameters. Overspeed operation is

strictly prohibited to ensure safe operation.

(2)RCF set：Press“Set”to move the cusrsor to“Speed indicator”, when flashing，it is speed &

RCF switching state，Press“+”or“-” Switch the speed to RCF, “RCF”indicator，Press“Set”

move to，“Speed/RCF set”，when flashing，Press“+”or“-” to set and press “Enter” confirm

(3)Time：press“Set” to move the cursor to“Time Set”, when flashing，Press "+" or "-" to time

set，then press“Enter” confirm.

（4）Acc/Dec Set：press“Set” to move the cursor to“Acc” or “Dec”, when flashing，Press "+"

or "-" to acc/Dec set，then press“Enter”to confirm.

The system supports 0- 9 a total of 10 files, 0 is the fastest, 9 is the slowest, when the

use of larger volume of the angle rotor or swing-out rotor, you can choose a little bit of the

slows, the other can choose a little faster file Bit. Generally recommended to use 5 files;

Finally press "Enter" to confirm.

7) When the "Short" button is pressed, the machine centrifuges, and when the mobile phone

is loosened, centrifugation stops.

Remind: each step is completed, should immediately press the "Enter" to be confirmed.

8) Finally, check the parameters on the screen confirm correct, press the "Start" " to run.

9) The running time countdown to "0", the centrifuge will automatically stop, the buzzer

ring, when the speed is 0, press the "Stop / Open" button, you can open the lid. During the

event of an emergency, press the "Stop / Open" button, the buzzer does not ring when the

centrifuge stops running.

Note: Do not open frequently, the proposed interval of 10 seconds to avoid

damage to components

10) Open, take out the tube carefully, complete the separation process.

11) turn off the power switch, cut off the centrifuge power.

VIII、Troubles & Solutions

Troubles

Cause

Solution

No display when power

plugged in

No power

Power check

Fuse blown

Check & replace

Cable connection loose

Check & reconnect

Large vibration

Tube No Symmetrically placed

Check & adjust

Tube broken

Check & replace

rotor not tightened

Check & adjust

Partial damage to shock

Check & replace

Display 0000 ，Start no

running

Circuit board or transformer

damaged

replace

control system connector is

loose

Re-tighten

Key damaged

replace

Motor damage or leakage

replace

Running but not speed, the

machine has strange sound or

smell

Control system or motor failure

manufacturers

maintenance

The machine with fault prompt, when the machine fails, the "display window" will

display the following items:

Unbalance

Over-speed

Lid-open

Lid exception

Temperature sensor error

Over temperature

Motor stall

Communication error

System error

Low voltage

Overcurrent protection

Motor fault (Hall state error)

Brake resistance

Note:

The above alarm is displayed in the "display window", when appears, the buzzer

alarm for a long time short and alarm shutdown. In the event of an alarm, the machine

will be correct display only when the fault is released. If the fault is not released, press

the “Enter”to clear the buzzer alarm. At this time, the fault display will not be cleared.

When the hardware fault is solved, press the Enter key again to clear the fault display

IX、INSTALLATION

1、Out of the box check

a) Before receiving the instrument, you should carefully check for transport damage. If

so, please reject the goods and inform the Company in writing and take pictures of

the damaged machine.

b) check whether the goods match the order list, if not, please contact the company.

c) 1.3, remove the packaging, and remove the contents of the centrifugal chamber.

2、Installation

a) Installation site requirements

the installation of the table should be strong, dry room, clean, to avoid direct

sunlight.

the room should have a separate ground, to ensure safe use of electricity.

b) the installation of the centrifuge

A), the centrifuge installed to a solid table to ensure that the four foot contact with

the table.

B), centrifuge around the gap with the wall should be greater than 16cm, to ensure

good ventilation.

C), power exchange 220V 50Hz 10A or 110v 60Hz, the wire cross-sectional area of

not less than 2 square millimeters, the socket capacity of not less than 10A, the

protective grounding wire must be connected firmly.

X、MAINTENANCE

1. After using, such as the day is no longer used, please use a clean soft cloth to clean the

centrifuge chamber, rotor and centrifuge tube.

2. Regularly check the rotor and centrifuge tube is cracked.

3. If not use the machine more than a month time, please remove the rotor from the

centrifuge chamber, the rotor center hole and centrifuge spindle coated with grease, keep

the rotor dry.

4. regular inspection of moving parts, such as gas spring seat, lid hinges and other screws

fastening.

XI、WARRANTY

Tabla de contenidos

Otros manuales de Equipo de laboratorio de MRC

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario