MRC WBL-MINI Manual de usuario

WBL-MINI

COOLING WATER CIRCULATOR

Operating Instructions

Operating Mamual

Before you operate the equipment please read carefully all the

instructions and safety notes. If you have any questions please phone us!

Follow the instructions on setting up, operation etc. This is the only

way to exclude incorrect operation of the equipment and to ensure full

warranty protection

1、Safety notes

· Transport the equipment with care!

· Careful transportation of the equipment requested !

· The unit may NEVER be overturned nor put upside down !

· Equipment and its internal parts can be damaged :

- by dropping

- by shock.

· Equipment should only be operated by properly instructed personnel !

· Never operate the equipment without bath liquid!

· Do not start up the equipment if

- it is damaged or leaking

- the supply cable is damaged.

· Switch off the equipment and pull out the mains plug for:

- servicing or repair

- before moving the equipment!

· Drain the bath before moving the equipment!

· Have the equipment serviced or repaired only by properly qualified

personnel!

2、Unpacking

Goods are packed carefully, largely preventing transport damage.

After unpacking , check first the equipment and accessories for possible

transport damage. If unexpectedly any damage can be noticed on the equipment it is

essential to notify the forwarding agent or the postal authorities so that an inspection

can take place.

Do not start operations with damaged instruments!

The unit may NEVER be overturned nor put upside down !

3、Equipment description

Materials

All components in contact with the thermostating liquid are made from materials

suitable for the recommended liquids and temperature. The materials used are

rustfree stainless steel, copper, brass, NBR, plastics.

Refrigeration unit

The refrigeration unit consists essentially of a fully sealed compressor. The

thermostating liquid is cooled through a heat exchanger located inside the bath. Heat

of condensation and motor heat are dissipated on air-cooled units through a

fan-cooled ribbed condenser.

The refrigeration unit is protected against overpressure and compressor overload.

With insufficient ventilation of the condenser (e.g. dirt deposits) the equipment is

switched off.

Control unit

The control unit with indication and operating functions,

The equipment is provided with a LED display to indicate the measurements and

settings as well as the operational status. The setpoint and other settings are

selected using two or three keys.

A Pt 100 temperature probe senses the outflow temperature inside the bath. The

measurement is processed by a high-resolution AD converter. Further processing

involves a special control algorithm to operate the heating triac (with reduced

reaction on the mains supply), the automatic compressor control, and the cooling

control which operates with low-noise solenoid valves. The proportional cooling

principle permits control in the cooling range without any energywasting

counter-heat.

4、Brief instructions

4.1 Assembly and setting up

It is advisable to set up the equipment so that the control unit is towards the

front and that the ventilation for the refrigeration unit, especially on equipment with

air-cooled condenser, (ventilation grille in lower part) is not impeded. Ensure a

minimum spacing of 0.5 m between ventilation grille and wall.

4.2 Filling and connection of external circuit

Fill the equipment with the appropriate circulating liquid to suit the operating

temperature. It should be filled with pure water, or a water-glycol mixture (min.

70:30%)!!

When using water as heat carrier at WBL-MINI please make sure that there

are no operating temperatures below 5°C in the outflow.

To assist in venting the pump, the pressure connection should be left open

when the equipment is filled for the first time, otherwise there may be permanent

damage to the pump!

Remove the plug on the filler opening at the upside. A funnel can be used for

filling..

When starting up for the first time, fill the bath as full as possible, up to the

max. level .

After filling up an external circuit further liquid may have to be added.

Connect the pump connections at the back of the equipment to the external

circuit. The external circuit must be pressure-tight.

Switch off the equipment before releasing the hose connections; the hose

couplings are not self-sealing!

Always ensure maximum flow cross-section in the external circuit (nipples,

tubing, external apparatus). This results in increased flow rate and therefore better

thermostating.

The equipment is designed for operation with non-flammable liquids.

Flammable liquids must not be used at temperatures higher than 25°C below the

flame point

4.3 Connection to the supply

Connect the equipment only to a supply socket with protective earth contact.

Check the details on the rating label against the supply voltage.

No warranty when the equipment is connected to the wrong supply!

4.4 Emptying

Place a container underneath the drain cock on the back of the equipment.

Switch off the equipment!

Observe the appropriate regulation when disposing of used circulating liquid.

Close the drain cock!

5、Operating panel

Key functions

① POWER Power key

② COOL Cooling Key

③ PUMP Circulating Key

④Setup key, for accessing parameter table, and confirming change.

Data shift key, also for activating auto turning

⑥Date increase key

⑦ Data decrease key

Display window

PV Process Value Display Displays PV, or code of a parameter

SV Setting Value Display Displays SV, alarming code, or value of a parameter

OPERATION DESCRIPTION

●Basal display status :

When power on, the upper display window of the instrument shows the process

value (PV), and the lower window shows the setpoint (SV). This status is called

basal display status. When the input signal is out of the measurable range (for

example, the RTD circuit is break, or input specification sets wrong), the upper

display window will alternately display “orAL” and the high limit or the low limit of PV,

and the instrument will automatically stop output.

●Set Value Setting:

In basal display status, we can set setpoint (SV) by pressing 、、 or .

Press to decrease the value , to increase the value, and to move

to the digit expected to modify. Keep pressing or , the speed of

decreasing or inscreasing value get quick.

●Parameter Setting:

In basal display status, press and hold for about 2 seconds can access Field

Parameter Table. Pressing can go to the next parameter;pressing 、

or can modify a parameter. The instrument will escape auomatically from

the parameter table if no key is pressed within 30 seconds.

●Intelligence control and auto tuning

When At control method is chosen, the control parameters can be obtained by

running auto-tuning. At the first time of running auto-tuning, in basic display status,

“At” will flash at lower display window and the instrument executes on-off control.

After 2 to 3 cycles of on-off action, the instrument will obtain the values of PID control

parameters. If you want to escape from auto tuning status, press and hold for

about 2 seconds until the "At" flash stops. Depending on the system, the time of auto

tuning can be several seconds to several hours. After the auto tuning finishes, the

parameter “At” automatically changes to “OFF”, If user wants to run auto tuning

again, setting parameter “At” to “on”.

Note 1: Before running auto-tuning, setpoint should be set to an often-used value or middle

value first, and then start auto-tuning. Generally, for application with heating time of 10%～80%

can obtain satisfying auto-tuning result. If the heating time is not in the range of 10～80%, the

auto-tuning will run for a long time and can’t get satisfying result. Raising setpoint for heating

time less than 10% or decreasing setpoint for heating time greater than 80% can improve

auto-tuning result.

Note 2: Don’t modify the setpoint during auto-tuning. It may affect the precision of auto-tuning.

Note 3: The temperature fluctuation caused by interference may affect the precision of

auto-tuning. Besides checking the wiring, increasing the parameter FILt (input digital filter) can

also reduce interference.

Note 4: After auto-tuning finishes, generally, the temperature rising has a little over-shoot (about

1～3℃). It is because considering that the transducer is often placed between the heater and

heated material, and a little over-shoot can shorten the time of rising to setpoint and save power.

(Generally, the temperature of transducer can be raised quick than that of heated material)

6、Technical data

Specifications for WBL-MINI

Model

Parameters WBL-MINI

Temperature range@25℃0~35℃

Temperature Stability ±0.1℃

Cooling Capacity@20℃300W

Pumppressure 0.4 / 0.46bar

Pump Flow Rate 7-10 L / min

Working mode Continuous

Filling Port mm Ø25

Reservoir Capacity 4.5 L

Dimensions mm 235W×475D×490H

Power Volts Hz Amps AC220V，50Hz，10A

Shipping Weight kg 23

7、Maintenance

7.1 Cl eaning

Before cleaning the equipment, pull out the mains plug!

The unit can be cleaned with water with the addition of a few drops of a detergent

(washing-up liquid), using a moist cloth.

Water must not enter the control unit

The user is responsible for carrying out an appropriate detoxification of any

dangerous material which has been spilled on or in the unit. This applies in particular

when the unit is passed on to someone else for operation, repair, storage etc..

7.2 Maintenance of the refrigeration unit

The refrigeration unit operates largely maintenance-free. If the unit is being operated

in a dusty atmosphere the condenser of the refrigerator has to be cleaned at

intervals of 4 to 6 months or more frequently. This is best done by blowing

compressed air or nitrogen into the ventilation openings for a few minutes. It may be

useful to unscrew the front grille.

This can be done in a most suitable way by screwing off the ventilation grid, then

cleaning the condenser with a vaccuum cleaner (using the brushtop).

7.3 Repair and disposal instruction

The refrigeration unit is filled with refrigerant. Repair and disposal must only be

carried out by a qualified refrigeration technician!

Before you return the equipment for servicing it is advisable to contact our Technical

Service department.

If the equipment has to be returned to the factory, please ensure that it is carefully

and properly packed. We accepts no responsibility for damage due to unsatisfactory

packing.

7.4 About us

We are available any time for your queries, suggestions and critic

Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529 [email protected]

MRC.10.16

Tabla de contenidos

Otros manuales de Equipo de laboratorio de MRC

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario