MRC CCM-10 Manual de usuario

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION

3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529 mrc@mrclab.com

MRC.VER.01-07.10

INSTRUCTION MANUAL FOR

Table Cut Mill

&&0

Ⅰ、

OUTLINE

【1】Wind outlet 【7】Current meter

【2】Pulverized material

outlet

【8】Power switch

【3】Shaft base (for holding

the shaft

【9】No Fuse Breaker (NFB)

【4】Loading tube 【10】Wind power adjuster

【5】Loading trough 【11】Pulverizing trough

【6】Screw for tightening

the loading tube

1

Ⅱ、

OPERATION

1. At first, please make sure whether the wind outlet (【1】) &

pulverized material outlet (【2】) have been covered with the cloth

pipes.

The cloth pipe for covering (【1】) is shorter and there’s a loop for

hanging on the shaft.

The cloth pipe for covering (【2】) is longer.

2. Unlock the screw (【6】) and pull up the upper base, and then insert

into the suitable meshes.

Combination A: Mesh 3~9mm + holder is for getting thick

pulverized materials.

Combination B: Mesh 3~9mm + Mesh 0.3~0.5mm + holder is for

getting thin pulverized materials.

If thick materials were asked to get into thin pulverized materials,

please process combination Afirst and then process combination B.

Such arrangement will gain better effect and keep a longer using

life of the meshes.

3. Please ensure the pulverizing trough (【11】) is empty, or clean it

and then to tighten the screw (【6】).

4. Plug in the socket and switch on (【8】).

5. Let materials be loaded through from the loading trough (【5】) into

the pulverizing trough (【11】) slowly and process pulverizing.

6. The cloth pipe can collect the pulverized materials which should be

small and could pass the meshes to get to the outlet.

7. After pulverizing, please switch off the machine and wait just few

minutes. Finally, the cloth pipe could be loosed and discharge the

pulverized materials.

2

III

、

CAUTION

1. When NFB is cut off, please turn off the power switch for 10

minutes and press NFB again to restart. The following situations

would be the possible reasons to cause a NFB to be cut off.

1) The speed of material loading is too fast. It’s necessary to

discharge the material more or less before re-starting.

2) When the motor is overloaded or over heat, please turn off the

machine for a while.

When the above situations are solved, users just need push down

the NFB and turn on the power switch.

2. Watch the current meter for avoiding the motor overloading and

being out of order soon.

3. For pulverizing the thick materials, the wind power adjuster (【10】)

could be closed for keeping all materials inside. For pulverizing the

thin materials, the enter gate should be just little opened for

controlling the speed of loading. Use the wind power adjuster

(【10】) to control the wind power.

4. The pulverized trough couldn’t be cleaned up by water.

IV

、

ACCESSORIES

1. Cloth pipes: two pcs (one is long and the other is short)

2. Shaft:1 pc

3. Mesh set: specifics – 75*118mm

、

holder*1pc

mesh size – 0.3m/m * 2 pcs, 0.4m/m * 1 pc,

0.5m/m * 1 pc, 3m/m * 1 pcs,

8m/m * 1 pc, 13m/m * 1 pc

3

Tabla de contenidos

Otros manuales de Equipo de laboratorio de MRC

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario