Moxa Technologies AirWorks AWK-5222 Manual de usuario

P/N: 1802052220012

AWK-5222

Quick Installation Guide

Moxa AirWorks

Third Edition, June 2014

- 2 -

Overview

The AWK-5222 dual-RF wireless AP/Bridge/Client provides a flexible and

highly reliable solution for your industrial wireless networks.

The AWK-5222 is rated to operate at temperatures ranging from 0 to

60°C for standard models and -40 to 75°C for extended temperature

models, and it is rugged enough for industrial applications.

With two independent RF modules, the AWK-5222 supports a greater

variety of wireless configurations and applications, and the redundant

wireless connections increase the reliability of your entire wireless

network.

The AWK-5222’s two DC power inputs make the power supply more

reliable, and it can also be powered via PoE for easier deployment.

Package Checklist

Moxa’s AWK-5222 is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

•1 AWK-5222

•2 Swivel-type Antennas (2dBi, RP-SMA, 2.4&5GHz)

•1 Quick Installation Guide

•1 Software CD

•1 Moxa Product Warranty Booklet

•1 Cable Holder with a Screw

•2 Protective Caps

Installation and Configuration

Before installing the AWK-5222, make sure that all items in the Package

Checklist are in the box. In addition, you will need access to a notebook

computer or PC equipped with an Ethernet port. The AWK-5222 has a

default IP address that you must use when connecting to the device for

the first time.

Step 1: Select the power source

The AWK-5222 can be powered by a DC power input or PoE (Power over

Ethernet). The AWK-5222 will use whichever power source you choose.

Step 2: Connect the AWK-5222 to a notebook or PC

Since the AWK-5222 supports MDI/MDI-X auto-sensing, you can use

either a straight-through cable or crossover cable to connect the

AWK-5222 to a computer. If the LED indicator on the AWK-5222’s LAN

port lights up, it means the connection is established.

Step 3: Set up the computer’s IP address

Set an IP address on the same subnet as the AWK-5222. Since the

AWK-5222’s default IP address is 192.168.127.253, and the subnet mask

is 255.255.255.0, you should set the IP address of the computer to

192.168.127.xxx and subnet mask to 255.255.255.0.

- 3 -

Step 4: Use the web-based manager to configure AWK-5222

Open your computer’s web browser and then type

http://192.168.127.253 in the address field to access the homepage of

the web-based management. Before the homepage opens, you will need

to enter the user name and password. For first-time configuration, enter

the default user name and password and then click on the Login button:

User name: admin

Password: root

ATTENTION

For security reasons, we strongly recommend

changing the

password. To do so,

select Maintenance



Password

, and then

follow the on-screen instructions.

Step 5: Select the operation mode for the AWK-5222

By default, the AWK-5222’s operation mode is set to Wireless

Redundancy. You can change the setting in Wireless Settings 

Operation mode if you would like to use the Wireless Bridge or AP-Client

mode.

NOTE

To make the change effective, you must click Save

Configurati

on to save the change or Restart



Save and

Restart button to apply all changes).

- 4 -

Panel Layout of the AWK-5222

1. Grounding screw

2. Terminal block for PWR1, PWR2,

relay, DI1, and DI2

3. Reset button

4. Heat dissipation orifices

5. AUX1 and AUX2 antenna ports

6. System LEDs: PWR1, PWR2,

PoE, FAULT, and STATE LEDs

7. WLAN LEDs: WLAN 1 and

WLAN2 LEDs

8. RS-232 console port

9. 10/100BaseT(X) RJ45 Port :

LAN1 and LAN2

10.

10M LED

11.

100M LED

12.

MAIN 1 antenna port

13.

MAIN 2 antenna port

14.

Model name

15.

Screw hole for wall mounting kit

16.

DIN-Rail mounting kit

Mounting Dimensions

- 5 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back

panel of the AWK-5222 when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the AWK-5222, make sure the

stiff metal spring is situated towards the top, as shown in the figures

below.

STEP 1:

Insert the top of the DIN

-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-Rail attachment unit will

snap into place as shown below.

To remove the AWK-5222 from the DIN-Rail, simply reverse Steps 1 and

Wall Mounting (optional)

For transportation applications that require an EN50155 certification

report, you should purchase the optional wall mount for the AWK-5222,

since the wall mount has passed EN50155 testing. The wall mount is also

convenient for other applications that require mounting the AWK-5222 to

a wall.

STEP 1:

Remove the aluminum

DIN

-Rail attachment plate

from the AWK

-5222, and

then attach the wall mount

plates with

M3 screws, as

shown in the adjacent

diagrams.

STEP 2:

Mounting the AWK

-5222 to a wall requires 4 screws.

Use the AWK

-5222 device, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the

shafts should be

less than 3.5 mm in diameter, as shown in the figure

at the right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

- 6 -

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates

before it is screwed into the wall.

STEP 3:

Once the screws are fixed into the

wall, insert the four screw heads

through the large opening of the

keyhole

-shaped apertures, and

then sli

de the AWK-5222

downwards, as indicated to the

right. Tighten the four screws for

added stability.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before in

stalling and/or

wiring your Moxa AWK-5222.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allow

ed for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

- 7 -

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked

“Class 2” or “LPS” and rated O/P: 12 to 48 VDC,

max 800

mW, 25°C.

ATTENTION

Make sure

the external power adapto

r (includes power cords and

plug assemblies) provided with the unit is certified and suitable

for use in your country.

Grounding the Moxa AWK-5222

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to

be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Redundant Power Inputs

The top two pairs of contacts of the 10-contact terminal block connector

on the AWK-5222’s top panel are used for the AWK-5222’s two DC inputs.

Top and front views of the terminal block connector is shown here.

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose,

use a small flat

blade screwdriver to tighten the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the AWK-5222’s t

panel.

ATTENTION

Before connecting

the AWK-5222

to the DC power inputs, make

sure the DC power source voltage is stable.

- 8 -

Wiring the Relay Contact

The AWK-5222 has one relay output, which consists of the two contacts of

the terminal block on the AWK-5222’s top panel. Refer to the previous

section for detailed instructions on how to connect the wires to the

terminal block connector, and how to attach the terminal block connector

to the terminal block receptor. These relay contacts are used to indicate

user-configured events. The two wires attached to the Relay contacts

form an open circuit when a user-configured event is triggered. If a

user-configured event does not occur, the Relay circuit will be closed.

Wiring the Digital Inputs

The AWK-5222 has two sets of digital input—DI1 and DI2. Each DI

comprises two contacts of the 10-pin terminal block connector on the

AWK-5222’s top panel. You can refer to the “Wiring the Redundant Power

Inputs” section for detailed instructions on how to connect the wires to

the terminal block connector, and how to attach the terminal block

connector to the terminal block receptor.

Cable Holder Installation (Optional)

You can attach the cable holder to the bottom of the AWK-5222. This

helps to keep cabling neat and avoid accidents that result from untidy

cables.

STEP 1:

Screw the cable holder onto the bottom of the

AWK

-5222.

STEP 2:

After mounting the AWK

5222 and plugging in the LAN cable, tighten the

cable along the device and wall.

- 9 -

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the AWK-5222’s front panel are

used to connect to Ethernet-enabled devices.

Below we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

RS-232 Connection

The AWK-5222 has one RS-232 (8-pin RJ45) console port located on the

front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect

the Moxa AWK-5222’s console port to your PC’s COM port. You may then

use a console terminal program to access the AWK-5222 for console

configuration.

Console Pinouts for 10-pin or 8-pin RJ45

10-Pin

Description

8-Pin

-----

DSR

RTS

GND

TxD

RxD

DCD

CTS

DTR

-----

NOTE

1. The pin numbers for male DB9 and DB25 connectors, and

hole numbers for female DB9 and DB25 connectors are

labeled on the connector. However, the numbers are

typically quite small, so you may need to use a magnifying

glass to see the numbers clearly.

2. The pin numbers for both 8-pin and 10-

pin RJ45 connectors

(and ports) are typically not labeled on the connector (or

port). Refer to the Pinout diagram above to see how RJ45

pins are numbered.

- 10 -

LED Indicators

The front panel of the Moxa AWK-5222 contains several LED indicators.

The function of each LED is described in the table below.

LED

Color

State

Description

Front Panel LED Indicators (System)

PWR1 Green

Power is being supplied from power

input 1.

Off Power is

not

being supplied from

power input 1.

PWR2 Green

Power is being supplied from power

input 2.

Off

Power is not being supplied from

power input 2.

PoE Amber

Power is being supplied via PoE.

Off

Power is not being supplied via PoE.

FAULT Red Blinking

Cannot get an IP address from the

DHCP server (interval: 1 sec)

Off

There is no error condition.

STATE Green/Red

Green

Software Ready.

Blinking

Green

The AWK has been located by AWK

Search Utility (interval: 1sec)

Red

Booting or Error condition.

WLAN1

Green/Amber

Green On

WLAN1 functions in Client mode.

Blinking

Green

WLAN1’s data communication is

running in Client mode.

Amber On

WLAN1 functions in AP/Bridge

mode.

Blinking

Amber

WLAN1’s data communication is

running in AP/Bridge mode.

Off

WLAN1 is not in use.

WLAN2

Green/Amber

Green On

WLAN2 function is in Client mode.

Blinking

Green

WLAN2’s data communication is

running in Client mode.

Amber On WLAN2 function is in AP/Bridge

mode.

Blinking

Amber

WLAN2’s data communication is

running in AP/Bridge mode.

Off

WLAN2 is not in use.

TP Port (LAN1, LAN2) LED Indicators (Port Interface)

10M Yellow

TP port’s 10 Mbps link is active.

Blinking

Data is being transmitted at 10

Mbps

Off

TP port’s 10 Mbps link is inactive.

100M Green

TP port’s 100 Mbps link is active.

Blinking

Data is being transmitted at 100

Mbps

Off

TP port’s 100 Mbps link is inactive.

Otros manuales para AirWorks AWK-5222

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Moxa Technologies

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1100 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1127 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131A-RTG Series Manual de usuario

Moxa Technologies

Moxa Technologies airworks awk-5232 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121-RTG Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-6222 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorksAWK-6232-M12 Manual

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manual de usuario

Moxa Technologies

Moxa Technologies TAP-6226 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131-M12-RCC Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1127 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3121B Series Manual de usuario

Moxa Technologies

Moxa Technologies AWK-6232 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manual de usuario

Moxa Technologies

Moxa Technologies WAC-1001 Series Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131A-M12-RTG Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A-M12-RCC-EU Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1200-AP Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3121-M12 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-4121 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manual de usuario

Moxa Technologies

Moxa Technologies WAC-1001 Series Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario