Moxa Technologies AirWorks AWK-3121 Manual de usuario

Reproduction without permission is prohibited.

P/N: 1802031210015

AWK-3121

Quick Installation Guide

Moxa AirWorks

Sixth Edition, June 2014

www.ipc2u.ru

www.moxa.pro

- 2 -

Overview

The AWK-3121 Access Point is ideal for industrial hard to wire applications,

keeping wireless costs under control, and integrating with existing mobile

equipment. The AWK-3121 is compliant with the industrial standards and

approvals, covering operating temperature, power input voltage, surge,

ESD and vibration. Installation is easy, with either DIN-Rail mounting or

distribution boxes, and the DIN-Rail mounting capability, wide operating

temperature range, and IP30 housing with LED indicators make the

AWK-3121 a convenient yet reliable solution for any industrial wireless

application.

Package Checklist

Moxa’s AWK-3121 is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

•1 AWK-3121

•2 Dual-band Omnidirectional Antennas (2dBi, RP-SMA, 2.4&5GHz)

•1 Quick Installation Guide

•1 Software CD

•1 Moxa Product Warranty Booklet

•1 Cable Holder with a Screw

•2 Protective Caps

www.ipc2u.ru

www.moxa.pro

- 3 -

Panel Layout of the AWK-3121

1. Grounding screw

Terminal block for PWR1, PWR2,

relay, DI1, and DI2

3. Reset button

4. Heat dissipation orifices

5. System LEDs: PWR1, PWR2,

PoE, FAULT, and STATE LEDs

6. LEDs for signal strength

7. WLAN LEDs: CLIENT, BRIDGE,

and WLAN LEDs

8. RS-232 console port

9. 10/100BaseT(X) RJ45 Port

10.

10M LED

11.

100M LED

12.

MAIN antenna port

13.

AUX antenna port

14.

Model name

15.

Screw hole for wall mounting kit

16.

DIN-Rail mounting kit

www.ipc2u.ru

www.moxa.pro

- 4 -

Mounting Dimensions

Unit = mm (inch)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back

panel of the AWK-3121 when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the AWK-3121, make sure the

stiff metal spring is situated towards the top, as shown in the figures

below.

STEP 1:

Insert the top of the DIN

-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-Rail attachment unit will

snap into place as shown below.

To remove the AWK-3121 from the DIN-Rail, simply reverse Steps 1 and

www.ipc2u.ru

www.moxa.pro

- 5 -

Wall Mounting (optional)

For some applications, it may be more convenient to mount the

AWK-3121 to a wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN

-Rail attachment plate

from the AWK

-3121, and

then attach the wall mount

plates with M3 screws, as

shown in the adjacent

diagrams.

STEP 2:

Mounting the AWK

-3121 to a wall requires 4 screws.

Use the AWK

-3121 device, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the

shafts should be

less

than 3.5 mm in diameter, as shown in the figure at the

right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates

before it is screwed into the wall.

STEP 3:

Once the screws are fixed into the

wall, insert the four screw heads

through the large opening of the

keyhole

shaped apertures, and then

slide the AWK

-3121 downwards, as

indicated to the right. Tighten the

four screws for added stability.

www.ipc2u.ru

www.moxa.pro

- 6 -

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord

before installing and/or

wiring your Moxa AWK-3121.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowed for e

ach wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked

“Class 2” or “LPS” and rated O/P: 12 to 48 VDC

, minimum

6 W (12 V/0.494 A to 48V/0.121 A), 25°C.

ATTENTION

Make sure

the external power adapto

r (includes power cords and

plug assemblies) provided with the unit is certified and suitable

for use in your country.

www.ipc2u.ru

www.moxa.pro

- 7 -

Grounding the Moxa AWK-3121

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Redundant Power Inputs

The top two pairs of contacts of the 10-contact terminal block connector

on the AWK-3121’s top panel are used for the AWK-3121’s two DC inputs.

Top and front views of the terminal block connector are shown here.

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose,

use a small flat

blade screwdriver to tighten the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which

is located on the AWK-3121’s t

panel.

ATTENTION

Before connecting the

AWK-3121

to the DC power inputs, make

sure the DC power source voltage is stable.

Wiring the Relay Contact

The AWK-3121 has one relay output, which consists of the two contacts of

the terminal block on the AWK-3121’s top panel. Refer to the previous

section for detailed instructions on how to connect the wires to the

terminal block connector, and how to attach the terminal block connector

to the terminal block receptor. These relay contacts are used to indicate

user-configured events. The two wires attached to the Relay contacts

form an open circuit when a user-configured event is triggered. If a

user-configured event does not occur, the Relay circuit will be closed.

www.ipc2u.ru

www.moxa.pro

- 8 -

Wiring the Digital Inputs

The AWK-3121 has two sets of digital input—DI1 and DI2. Each DI

comprises two contacts of the 10-pin terminal block connector on the

AWK-3121’s top panel. You can refer to the “Wiring the Redundant Power

Inputs” section for detailed instructions on how to connect the wires to

the terminal block connector, and how to attach the terminal block

connector to the terminal block receptor.

Cable Holder Installation (Optional)

You can attach the cable holder to the bottom of the AWK-3121. This

helps to keep cabling neat and avoid accidents that result from untidy

cables.

STEP 1: Screw the cable holder onto the bottom

of the AWK

-3121.

STEP 2:

After mounting the AWK-3121 and plugging in the LAN cable,

tighten the cable

along the device and wall.

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the AWK-3121’s front panel are

used to connect to Ethernet-enabled devices.

Below we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

www.ipc2u.ru

www.moxa.pro

- 9 -

RS-232 Connection

The AWK-3121 has one RS-232 (8-pin RJ45) console port located on the

front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect

the Moxa AWK-3121’s console port to your PC’s COM port. You may then

use a console terminal program to access the AWK-3121 for console

configuration.

Console Pinouts for 10-pin or 8-pin RJ45

10-Pin

Description

8-Pin

-----

DSR

RTS

GND

TxD

RxD

DCD

CTS

DTR

-----

NOTE

1. The pin numbers for male DB9 and DB25 connectors, and

hole numbers for female DB9 and DB25 connectors are

labeled on the connector. However, the numbers are

typically quite small, so you may need to use a magnifying

glass to see the numbers clearly.

2. The pin numbers for both 8-pin and 10-

pin RJ45 connectors

(and ports) are typically not labeled on the connector (or

port). Refer to the Pinout diagram above to see how RJ45

pins are numbered.

ATEX Information

1. DEMKO certification number: 10 ATEX 0902666X

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string: Ex nA nL IIC T4

4. Standards covered ( EN60079-0:2006, EN60079-15:2005)

5. The conditions of safe usage:

a. The Ethernet Communication Devices are intended for mounting

in an IP54 enclosure and used in an area of not more than

pollution degree 2 as defined by IEC60664-1.

b. Conductors suitable for use in an ambient temperature greater

than 93°C must be used for the Power Supply Terminal.

c. A 4 mm2 conductor must be used when connection to the

external grounding screw is utilized.

d. Cables must be suitable for use in an ambient temperature

greater than 93°C.

www.ipc2u.ru

www.moxa.pro

- 10 -

LED Indicators

The front panel of the Moxa AWK-3121 contains several LED indicators.

The function of each LED is described in the table below.

LED

Color

State

Description

Front Panel LED Indicators (System)

PWR1 Green

Power is being supplied from powerinput 1.

Off

Power is not being supplied frompower

input 1.

PWR2 Green

Power is being supplied from power input 2.

Off

Power is not being supplied from power

input 2.

PoE Amber

Power is being supplied via PoE.

Off

Power is not being supplied via PoE.

FAULT Red

Blink

(slow)

Cannot get an IP address from the

DHCP server (interval: 1 sec)

Blink

(fast)

IP address conflict (interval: 0.5 sec)

Off

Error condition does not exist.

STATE Green/

Red

Green

Software Ready

Green

Blink

The AWK has been located by AWK

Search Utility. (interval: 1sec)

Red

Booting error condition

SIGNAL

(5 LEDs) Green

Signal level(for Client/Slave mode only)

Off

BRIDGE Green

WLAN function is in Bridge(WDS) Mode.

Off

WLAN is not in Bridge(WDS) Mode.

CLIENT Green

WLAN function is in Client/Slave mode and

AWK has established a link with an AP.

Blink

WLAN data communication is run in

Client/Slave mode

Off

WLAN is not in Client Mode or AWK has not

established a link with an AP.

WLAN Amber

WLAN functions in AP/Bridge/Master mode.

Blink WLAN’s data communication is run in

AP/Bridge/Master mode

Off

WLAN is not in use or not working properly

TP Port LED Indicators (Port Interface)

100M Green

TP port’s 100Mbps link is active.

Blink

Data is being transmitted at 100 Mbps

Off

TP port’s 100Mbps link is inactive.

10M Amber

TP port’s 10Mbps link is active.

Blink

Data is being transmitted at 10 Mbps

Off

TP port’s 10Mbps link is inactive.

www.ipc2u.ru

www.moxa.pro

Otros manuales para AirWorks AWK-3121

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Moxa Technologies

Moxa Technologies

Moxa Technologies AirWorks AWK-1200-AP Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1127 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121-M12-RTG Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131-RCC Series Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131A-M12-RTG Manual de usuario

Moxa Technologies

Moxa Technologies airworks awk-5232 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manual de usuario

Moxa Technologies

Moxa Technologies AWK-4131 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1127 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-4121 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-4121 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131A-RTG Series Manual de usuario

Moxa Technologies

Moxa Technologies Airworks AWK-3131A-M12-RCC Manual de usuario

Moxa Technologies

Moxa Technologies WAC-1001 Series Manual de usuario

Moxa Technologies

Moxa Technologies AirWorksAWK-6232-M12 Manual

Moxa Technologies

Moxa Technologies AirWorks AWK-6222 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131A-M12-RTG-EU-T Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario