Moxa Technologies AirWorks AWK-1131A Manual de usuario

Reproduction without permission is prohibited.

P/N: 1802011310012

1802011310012

AWK-1131A

Quick Installation Guide

Moxa AirWorks

Third Edition, July 2015

- 2 -

Overview

The AWK-1131A industrial wireless Access Point meets the growing need

for faster data transmission speeds by supporting IEEE 802.11n

technology with a net data rate of up to 300 Mbps. The AWK-1131A is

compliant with the industrial standards and approvals, covering operating

temperature, power input voltage, surge, ESD and vibration. The two

redundant DC power inputs increase the reliability of the power supply.

The AWK-1131A can operate on either the 2.4 or 5 GHz bands and is

backwards-compatible with existing 802.11a/b/g deployments to

future-proof your wireless investments.

Package Checklist

Moxa’s AWK-1131A is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

•1 AWK-1131A

•2 dual-band omni-directional antennas, 2 dBi, RP-SMA (male)

•1 quick installation guide

•1 document and software CD

•1 Moxa product warranty booklet

•1 plastic RJ45 protective cap for console port

- 3 -

Panel Layout of the AWK-1131A

Top Panel View

Front Panel View

Rear Panel View

1. Grounding screw (M5)

2. Terminal block for PWR1 and

PWR2

3. RS-232 console port

4. Antenna B port

5. System LEDs:

PWR, FAULT, and

STATE LEDs

6. LEDs for signal strength

7. WLAN LEDs

8. 10/100/1000BaseT(X) RJ45

Port

9. Antenna A port

10.

Screw hole for wall mounting kit

11.

DIN-Rail mounting kit

12.

Reset button

13.

10/100M LED

14.

1000M LED

- 4 -

Mounting Dimensions

Unit = mm (inch)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back

panel of the AWK-1131A when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the AWK-1131A, make sure the

stiff metal spring is situated towards the top, as shown in the figures

below.

STEP 1:

Insert the top of the DIN

-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-Rail attachment unit will

snap into place as shown below.

To remove the AWK-1131A from the DIN-Rail, simply reverse Steps 1 and

- 5 -

Wall Mounting (optional)

For some applications, it may be more convenient to mount the

AWK-1131A to a wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN

-Rail attachment plate

from the

AWK-1131A, and

then attach the wall mount

plates with M

3 screws, as

shown in the adjacent

diagrams.

STEP 2:

Mounting the

AWK-1131A

to a wall requires 4 screws.

Use the

AWK-1131A device, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the

shafts should be less

than 3.5 mm in diameter, as shown in the figure at the

right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates

before it is screwed into the wall.

STEP 3:

Once the screws are fixed into

the wall, insert the four screw

heads through the large opening

of the keyhole

-shaped

apertures, and then slide the

AWK

-1131A downwards, as

indicated to the right. Tighten

the four screws for added

stability.

- 6 -

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa AWK-1131A.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowed for each wire size.

If the current goes above the maximum

ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

•

NOTE

Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked

“Class 2” or “LPS” and rated O/P:

6.72W (12V/0.56A to

48V/0.14A), 25°C.

ATTENTION

Make sure

the external power adapto

r (includes power cords and

plug assemblies) provided with the unit is certified and suitable

for use in your country.

- 7 -

Grounding the Moxa AWK-1131A

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is

intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Redundant Power Inputs

The 4-contact terminal block connector on the AWK-1131A’s top panel is

used for the AWK-1131A’s two DC inputs. The top and front views of the

terminal block connector are shown here.

Top View

Front View

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose,

use a small flat

blade screwdriver to tighten the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the AWK-1131A’s

op panel.

ATTENTION

Before connecting

the AWK-1131A

to the DC power inputs, make

sure the DC power source voltage is stable.

- 8 -

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the AWK-1131A’s front panel are

used to connect to Ethernet-enabled devices. Below we show pinouts for

both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

1000BaseT Ethernet Port Connection

1000BaseT data is transmitted on differential TRD+/- signal pairs over

copper wires.

MDI/MDI-X Port Pinouts

Signal

TRD(0)+

TRD(0)-

TRD(1)+

TRD(2)+

TRD(2)-

TRD(1)-

TRD(3)+

TRD(3)-

RS-232 Connection

The AWK-1131A has one RS-232 (8-pin RJ45) console port located on the

top panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect

the Moxa AWK-1131A’s console port to your PC’s COM port. You may then

use a console terminal program to access the AWK-1131A for console

configuration.

Console Pinouts for 10-pin or 8-pin RJ45

10-Pin

Description

8-Pin

–

DSR

RTS

GND

TxD

RxD

DCD

CTS

DTR

–

NOTE

The pin numbers for both 8-pin and 10-pin RJ45 connectors (and

ports) are typically not labeled on the connector (or port). Refer

to the Pinout diagram above to see how RJ45 pins are numbered.

- 9 -

LED Indicators

The front panel of the Moxa AWK-1131A contains several LED indicators.

The function of each LED is described in the table below.

LED

Color

State

Description

Front Panel LED Indicators (System)

PWR1 Green

Power is being supplied from power

input 1.

Off Power is

not

being supplied from

power

input 1.

PWR2 Green

Power is being supplied from power

input 2.

Off

Power is not being supplied from power

input 2.

FAULT Red

Blink

(fast)

Cannot get an IP address from the

DHCP

server (interval: 0.5 sec)

Blink

(slow)

IP address conflict (interval: 1 sec)

Off

Error condition does not exist.

STATE Green/

Red

Green

Software Ready

Green

Blink

The AWK has been located by AWK

Search Utility. (interval: 1sec)

Red

Booting error condition

SIGNAL

(5 LEDs) Green

Signal level(for Client mode only)

Off

WLAN

Green

WLAN function is in Client mode and

AWK has established a link with an AP.

Blink

WLAN data communication is run in

Client mode

Off WLAN is not in Client Mode or AWK has

not established a link with an AP.

Amber

WLAN function is in AP mode.

Blink

WLAN’s data communication is run in AP

mode

Off

WLAN is not in use or not working

properly

TP Port(RJ45) LED Indicators (Port Interface)

1000M Green

TP port’s 1000Mbps link is active.

Blink

Data is being transmitted at 1000 Mbps

Off

TP port’s 1000Mbps link is inactive.

10/100M Amber

TP port’s 10/100Mbps link is active.

Blink

Data is being transmitted at 10/100

Mbps

Off

TP port’s 10/100Mbps link is inactive.

- 10 -

Specifications

WLAN Interface

Standards IEEE 802.11a/b/g/n for Wireless LAN

IEEE 802.11i for Wireless Security

IEEE 802.3 for 10BaseT

IEEE 802.3u for 100BaseTX

IEEE 802.3ab for 1000BaseT

Spread Spectrum and

Modulation (typical)

DSSS with DBPSK, DQPSK, CCK

OFDM with BPSK, QPSK, 16QAM, 64QAM

802.11b:

•CCK @ 11/5.5 Mbps

•DQPSK @ 2 Mbps

•DBPSK @ 1 Mbps

802.11a/g:

•64QAM @ 54/48 Mbps

•16QAM @ 36/24 Mbps

•QPSK @ 18/12 Mbps

•BPSK @ 9/6 Mbps

802.11n:

•64QAM @ 300 Mbps to BPSK @ 6.5 Mbps

(multiple rates supported)

Operating Channels

(central frequency)

US:

•2.412 to 2.462 GHz (11 channels)

•5.180 to 5.240 (4 channels)

•5.260 to 5.320 (4 channels)*

•5.500 to 5.700 GHz (8 channels - excludes

5.600 to 5.640 GHz)*

•5.745 to 5.825 GHz (5 channels)

EU:

•2.412 to 2.472 GHz (13 channels)

•5.180 to 5.240 (4 channels)

•5.260 to 5.320 (4 channels)*

•5.500 to 5.700 GHz (11 channels)*

JP:

•2.412 to 2.484 GHz (14 channels, DSSS)

•5.180 to 5.240 (4 channels)

•5.260 to 5.320 (4 channels)*

•5.500 to 5.700 GHz (11 channels)*

*DFS

(Dynamic Frequency Selection) channel support: In

AP mode, when a

radar signal is detected, the device will

automatically switch to another channel. However

according to regulations, after switching channels, a

60-second availability check period is required before

starting the service.

Security

•

SSID broadcast enable/disable

•Firewall for MAC/IP/Protocol/Port-based

filtering

•64-bit and 128-bit WEP encryption

•WPA/WPA2-Personal and Enterprise

(IEEE 802.1X/RADIUS, TKIP and AES)

Transmission Rates

•

802.11b: 1, 2, 5.5, 11 Mbps

•802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps

•802.11n: 6.5 to 300 Mbps

(multiple rates supported)

Otros manuales para AirWorks AWK-1131A

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Moxa Technologies

Moxa Technologies

Moxa Technologies airworks awk-5232 Manual de usuario

Moxa Technologies

Moxa Technologies Airworks AWK-3131A-M12-RCC Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121-RTG Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1200-AP Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manual de usuario

Moxa Technologies

Moxa Technologies AWK-6232 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-6222 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-6222 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131 Manual

Moxa Technologies

Moxa Technologies AWK-4121 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3121-SSC-RTG Manual de usuario

Moxa Technologies

Moxa Technologies TAP-6226 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3131A Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-5222 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-4121 Manual de usuario

Moxa Technologies

Moxa Technologies AWK-3131A-RTG Series Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-622 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1151C Series Manual de usuario

Moxa Technologies

Moxa Technologies TAP-213 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manual de usuario

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario