Moxa Technologies TN-5308-LV Manual de usuario

Moxa ToughNet Switch

TN-5308 Series

Layer 2 M12 unmanaged Ethernet switches

Hardware Installation Guide

First Edition, May 2009

Reproduction without permission is prohibited.

P/N: 1802053080010

—1 —

Overview

The ToughNet TN-5308 series M12 unmanaged Ethernet switches are

designed for industrial applications in harsh environments. The TN series

switches use M12 connectors to ensure tight, robust connections, and

guarantee reliable operation against environmental disturbances, such as

vibration and shock. The TN-5308 series Ethernet switches provide 8 Fast

Ethernet M12 ports, support IEEE 802.3/802.3u/802/3x with 10/100M,

full/half-duplex, MDI/MDI-X auto-sensing, and provide an economical

solution for your industrial Ethernet network. Models with an extended

operating temperature range of -40 to 75°C are also available. The TN-5308

series Ethernet switches are compliant with EN50155/50121-3-2/50121-4

(railway applications), NEMA TS2 (traffic control systems), and e-Mark

(vehicles) requirements, making the switches suitable for a variety of

industrial applications.

Package Checklist

Your TN-5308 is shipped with the following items. If any of these items is

missing or damaged, please contact your customer service representative for

assistance.

yMoxa ToughNet Switch

yPanel Mounting Kit

yHardware Installation Guide

yMoxa Product Warranty Statement

Features

High Performance Network Switching Technology

y8 10/100BaseT(X) ports

yStore and Forward switching process type

yIEEE 802.3/802.3u/802.3x

y10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing

Industrial-Specific Applications

ySupport 12/24/36/48 VDC (7 to 60 VDC) power input for “-LV” models

ySupport 72/96/110 VDC (50.4 to 154 VDC) power input for “-MV”

models

yActive circuit protection

Rugged Design

yM12 / M23 circular connectors for vibration-resistant robust connections

yOperating temperature range of 0 to 60°C, or extended operating

temperature range of -40 to 75°C for “-T” models

yIP40, rugged metal housing

yPanel mounting or DIN-rail mounting installation capability

—2 —

TN-5308-LV Panel Layouts

Front Panel View Rear Panel View

44 4

1. TP port’s 10/100 Mbps LED

2. 10/100BaseT(X) port

(female 4-pin shielded M12 connector with D coding)

3. Port label

4. Screw holes for panel mounting kit or DIN rail mounting kit

(there are 3 holes: top middle, bottom left, and bottom right)

5. Power input LED

6. Power input port

(male 5-pin shielded M12 connector with A coding)

7. Grounding screw

8. Power input port pin assignment

9. Model name

10. TP port pin assignment

11. Model label

—3 —

TN-5308-MV Panel Layouts

Front Panel View Rear Panel View

44 4

1. TP port’s 10/100 Mbps LED

2. 10/100BaseT(X) port

(female 4-pin shielded M12 connector with D coding)

3. Port label

4. Screw holes for panel mounting kit or DIN rail mounting kit

(there are 3 holes: top middle, bottom left, and bottom right)

5. Power input LED

6. Power input port

(male 5-pin shielded M23 connector with A coding)

7. Grounding screw

8. Power input port pin assignment

9. Model name

10. TP port pin assignment

11. Model label

—4 —

Mounting Dimensions (unit = mm)

TN-5308-LV

Side ViewFront ViewRear View DIN-Rail Mounting Kit

TN-5308-MV

Side ViewFront ViewRear View DIN-Rail Mounting Kit

—5 —

Panel/Wall Mounting

Mounting the TN-5308-LV/MV on the wall requires 3 screws. Please use the

3 screws packed in the panel mounting kit.

STEP 1: Prepare the 3 screw holes on the wall according to the positions of

the 3 screw holes on the switch shown on the mounting dimension diagram.

STEP 2: Use one screw to go through the top-middle screw hole on the

switch and screw it into the wall.

STEP 3: Screw in the remaining 2 screws through the bottom-left and

bottom-right holes on the switch to the wall.

NOTE The screw lengths of TN-5308-LV and TN-5308-MV are

different. TN-5308-LV uses M3 * 30 mm screws. TN-5308-MV

uses M3 * 40 mm screws. Please use the screws packed in the

panel mounting kit.

DIN-Rail Mounting (optional)

With the optional DIN-Rail mounting kit

DK-TN-5308 (must be purchased separately),

you can mount the TN-5308-LV/MV on a

35mm DIN-Rail.

STEP 1:

Fix the DIN-Rail attachment plate onto the rear

panel of the switch as shown in the figure at the

right.

STEP 2:

Position the TN-5308-LV/MV on the

DIN-Rail, tilting to hook clamps over

the top edge of the rail.

STEP 3:

Swing the switch down fully onto the

DIN-Rail until both clamps completely

latch.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the Moxa ToughNet Switch from the DIN-Rail, simply reverse

Steps 2 and 3 above.

—6 —

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage greater than what is

specified on the product label.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa switch.

This device has UL508 approval. Use copper conductors only,

60/75°C, and tighten to 4.5 pound-inches. For use in pollution

degree 2 environments.

ATTENTION

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size. If the current

goes above the maximum ratings, the wiring could overheat,

causing serious damage to your equipment.

Please read and follow these guidelines:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power

wiring through the same wire conduit. To avoid interference, wires

with different signal characteristics should be routed separately.

yYou can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

yKeep input wiring and output wiring separated.

yIt is strongly advised that you label wiring for all devices in the system

when necessary.

Grounding the TN-5308

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

grounding screw to the grounding surface prior to connecting devices.

—7 —

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

Connecting the Power Supply

The M12/M23 A-coded 5-pin male connector on the TN-5308-LV/MV front

panel is used for the DC power input. You have to prepare a power cord with

M12/M23 A-coded 5-pin female connector to connect the switch to the DC

power input.

Pinouts for the power input port on the TN-5308-LV

N.C. : Not connected

Pinouts for the power input port on the TN-5308-MV

STEP 1: Plug your power cord connector to the power input port of the

TN-5308 switch.

STEP 2: Screw the nut on your power cord connector to the power input

connector on the switch to ensure a tight connection.

ATTENTION

Before connecting the TN-5308 to the DC power input, make

sure the DC power source voltage is stable.

—8 —

Connecting the Data Lines

10/100BaseT(X) Ethernet Port Connection

All TN-5308 models have 8 10/100BaseT(X) Ethernet ports (4-pin shielded

M12 connectors with D coding). The 10/100TX ports located on the

TN-5308’s front panel are used to connect to Ethernet-enabled devices. Most

users configure these ports for Auto MDI/MDI-X mode, in which case the

port’s pinouts are adjusted automatically depending on the type of Ethernet

cable used (straight-through or cross-over), and the type of device (NIC-type

or HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

Pinouts for the 10/100BaseT(X) Ports on the TN-5308

Housing: shield

Pinouts for the RJ45 (8-pin) Port

RJ45 (8-Pin) MDI Port Pinouts MDI-X Port Pinouts

Pin Signal

1 Tx +

2 Tx -

3 Rx +

6 Rx -

Pin Signal

1 Rx +

2 Rx -

3 Tx +

6 Tx -

M12 (4-pin, M) to M12 (4-pin, M) Cross-Over Cable Wiring

Tx+

Rx+

Tx-

Rx-

Cross-Over Cable Wiring

Tx+

Rx+

Tx-

Rx-

—9 —

M12 (4-pin, M) to M12 (4-pin, M) Straight-Trough Cable Wiring

Tx+

Rx+

Tx-

Rx-

Straight-through Cable Wiring

Rx+

Tx+

Rx-

Tx-

M12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring

Tx+

Rx+

Tx-

Rx-

Cross-Over Cable Wiring

Tx+

Tx-

Rx+

Rx-

M12 (4-pin, M) to RJ45 (8-pin) Straight-Trough Cable Wiring

Tx+

Rx+

Tx-

Rx-

Straight-through Cable Wiring

Rx+

Rx-

Tx+

Tx-

Auto MDI/MDI-X Connection

The Auto MDI/MDI-X function allows users to connect TN-5308’s

10/100BaseTX ports to any kind of Ethernet device, without needing to pay

attention to the type of Ethernet cable being used for the connection. This

means that you can use either a straight-through cable or cross-over cable to

connect the TN-5308 to Ethernet devices.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Moxa Technologies

Moxa Technologies

Moxa Technologies EDS-405A Manual

Moxa Technologies

Moxa Technologies TN-5308-LV-T Manual de usuario

Moxa Technologies

Moxa Technologies ToughNet TN-4500A Series Manual de usuario

Moxa Technologies

Moxa Technologies ICS-G7 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-P308 Series Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-30 Manual

Moxa Technologies

Moxa Technologies PT-7710 Series Manual de usuario

Moxa Technologies

Moxa Technologies TN-5305-T Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PN Manual de usuario

Moxa Technologies

Moxa Technologies EDS-405A Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manual

Moxa Technologies

Moxa Technologies EDS-G308-T Manual

Moxa Technologies

Moxa Technologies IKS-6324 Series Manual

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manual de usuario

Moxa Technologies

Moxa Technologies PT-508 Series Manual

Moxa Technologies

Moxa Technologies EDS-2010-ML Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-600 Series Manual

Moxa Technologies

Moxa Technologies EDS-508A Series Manual de usuario

Moxa Technologies

Moxa Technologies PT-G7828 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-505A Series Manual

Moxa Technologies

Moxa Technologies NE-4100 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-505A Manual

Moxa Technologies

Moxa Technologies EDS-405A Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario