Moxa Technologies IESH-MB205G-C2E-R Series Manual de usuario

P/N: 1802020003070

*1802020003070*

IESH-MB205G-C2E-R/

IESH-MB208G-C2E-R Series

Quick Installation Guide

Misumi IESH-MB Switch

Version 1.0, July 2023

- 2 -

Overview

The IESH-MB205G-C2E-R/IESH-MB208G-C2E-R Series has a 5-port and

8-port combination to simplify network expansion. The compact

switches provide a cost-effective solution for your industrial Ethernet

connection requirements.

The IESH-MB205G-C2E-R/IESH-MB208G-C2E-R Series provides

12/24/48 VDC power input, and the switches are available with a

standard operating temperature range from -10 to 60°C. The switches

are rugged enough to operate reliably in harsh industrial environments.

To provide greater versatility for use with applications from different

industries, the IESH-MB205G-C2E-R/IESH-MB208G-C2E-R Series also

allows users to enable or disable broadcast storm protection (BSP),

Quality of Service (QoS) function via the DIP switches on the top panel.

The IESH-MB205G-C2E-R/IESH-MB208G-C2E-R switches can be easily

installed with DIN-rail mounting as well as distribution boxes. The DIN-

rail mounting capability with LED indicators ensure that the plug-and-

play IESH-MB205G-C2E-R/IESH-MB208G-C2E-R switches are reliable

and easy to use.

NOTE

Throughout this Quick Installation Guide, we use IESH-MB as

an abbreviation for Misumi IESH-MB Switch:

IESH-MB = Misumi IESH-MB Switch

ATTENTION

This device complies with part 15 of FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operations.

Package Checklist

Your IESH-MB is shipped with the following items.

•Misumi IESH-MB Switch

•Quick installation guide (printed)

- 3 -

Features

High Performance Network Switching Technology

•10/100/1000BaseT(X) auto-negotiation speed, full/half duplex

mode, auto MDI/MDI-X connection.

•IEEE 802.3 for 10BaseT.

•IEEE 802.3u for 100BaseT(X).

•IEEE 802.3ab for 1000BaseT(X).

•IEEE 802.3x for flow control.

•IEEE 802.1p for Quality of Service (QoS) traffic prioritized function.

•Store-and-forward switching process type.

Industrial-grade Reliability

•Broadcast storm protection to prevent network devices from

crashing.

Rugged Design

•Operating temperature range from -10 to 60°C.

•Rugged high-strength case.

•DIN-rail or wall mounting ability.

WARNING

The power for this product is intended to be supplied by a

Listed Power Supply, with output marked LPS, and rated to

deliver 12 to 48 VDC.

- 4 -

Panel Layout of IESH-MB205G-C2E-R

1. Chassis ground screw

2. Terminal block for power input

3. DIP switch

4. Power LED

5. 10/100/1000BaseT(X) Port

6. 10/100/1000BaseT(X) Port LED

7. Port number

- 5 -

Panel Layout of IESH-MB208G-C2E-R

1. Chassis ground screw

2. Terminal block for power input

3. DIP switch

4. Power LED

5. 10/100/1000BaseT(X) Port

6. 10/100/1000BaseT(X) Port LED

7. Port number

- 6 -

Mounting Dimensions

IESH-MB205G-C2E-R

IESH-MB208G-C2E-R

- 7 -

DIN-rail Mounting

When shipped, the DIN-rail mounting kit is fixed to the back panel of

the IESH-MB. Mount the IESH-MB on the corrosion-free mounting rail

that adheres to the EN 60715 standard.

Suggested Installation Method

STEP 1:

Insert the upper lip of the DIN-

rail kit into the mounting rail.

STEP 2:

Press the device towards the

mounting rail until it snaps into

place. Alternatively, you can use

a screwdriver to attach to the

bottom of the DIN-rail kit and pull

down.

Suggested Removal Method

STEP 1:

Pull down the latch on the DIN-

rail kit with a flat-head

screwdriver.

STEP 2:

Slightly pull the device forward

and lift up to remove it from the

mounting rail.

- 8 -

ATTENTION

When installing or removing the devices, please insert a flat-

head screwdriver into the latch of the holding clamp and pull

the latch downward rather than pushing it towards the DIN rail

side, when removing the module from the rail.

If you want to change the position of the device on the DIN rail,

please follow the steps shown in the images above. First,

remove the device using a flat-head screwdriver and then re-

install the device in the desired position. Please DO NOT directly

move the device on the DIN rail, without uninstalling it first.

If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may

be impaired.

Please use a flat-head screwdriver

with a head size of between 4 and 6

mm for proper installation or

removal.

WARNING

1. The installation and the safety of any system incorporating

the equipment is the responsibility of the assembler of the

system.

2. This is an open type module and should be installed in a

safety enclosure with mechanical rigidity and an

appropriate IP rating.

- 9 -

Wall Mounting (optional)

For some applications, you will find it convenient to mount IESH-MB on

the wall, as illustrated below.

There are two options for installation: The first option

is to hook the IESH-MB DIN-rail latch on the opening

of the wall mount kit (see picture above) and then

mount the wall-mount kit on the wall with screws.

(The other option is to perform these two steps in

the other order.) The heads of the screws should be

less than 6.0 mm in diameter, and the shafts should

be less than 3.5 mm in diameter, as shown in the

figure at the right.

NOTE

Before tightening screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into

one of the keyhole-shaped apertures of the Wall Mounting

Plates.

Do not screw the screws in all the way—leave about 2 mm to allow

room for sliding the wall mount panel between the wall and the screws.

Once the screws are fixed in the

wall, insert the two screw heads

through the large parts of the

keyhole-shaped apertures, and

then slide IESH-MB downwards,

as indicated. Tighten the two

screws for added stability.

WARNING

External parts are hot. Take necessary precautions if it is

necessary to touch.

- 10 -

Wiring Requirements

WARNING

Do not disconnect modules or wires unless the power supply

has been switched off or the area is known to be non-

hazardous. The devices may only be connected to the supply

voltage shown on the type plate.

The devices are designed for operation with a Safety Extra-Low

Voltage. Thus, they may only be connected to the supply

voltage connections and to the signal contact with the Safety

Extra-Low Voltages (SELV) in compliance with

IEC950/EN60950/VDE0805/UL 61010-1/UL 61010-2-201.

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Misumi IESH-MB Switch.

Calculate the maximum possible current in each power wire

and common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring

could overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power

wiring in the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring to all devices in the

system when necessary.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Moxa Technologies

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE Manual

Moxa Technologies

Moxa Technologies EDS-516A Series Manual

Moxa Technologies

Moxa Technologies SPL-24 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-528E Series Manual de usuario

Moxa Technologies

Moxa Technologies ICS-G7748A Series Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manual

Moxa Technologies

Moxa Technologies MDS-G4000-4XGS Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506E-4PoE Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 1220 Manual de usuario

Moxa Technologies

Moxa Technologies UPort 400A Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-305-T Manual

Moxa Technologies

Moxa Technologies PT-7528 Manual

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manual

Moxa Technologies

Moxa Technologies EDS-408A Manual de usuario

Moxa Technologies

Moxa Technologies TN-5305-T Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G308 Series Manual de usuario

Moxa Technologies

Moxa Technologies TRC-190 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-510E Series Manual de usuario

Moxa Technologies

Moxa Technologies TN-5308 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 1220 Manual de usuario

Moxa Technologies

Moxa Technologies PT-7728 Series Manual de usuario

Moxa Technologies

Moxa Technologies PT-G7509 Manual

Moxa Technologies

Moxa Technologies PT-508 Series Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario