Moxa Technologies EDS-528E Series Manual de usuario

P/N: 1802005280010

*1802005280010*

EDS-528E Series

Quick Installation Guide

Moxa EtherDevice™ Switch

Edition 1.0, June 2016

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Package Checklist

The EDS-528E is shipped with the following items. If any of these items

are missing or damaged, please contact your customer service

representative for assistance.

•1 EDS-528E Ethernet switch

•USB cable

•Protective caps for unused ports

•Quick installation guide (printed)

•Documentation and software CD

•Moxa product warranty statement

•Screws to fill unused screw holes to attain an IP30 rating

Features

•4 Gigabit combo Ethernet ports plus 24 Fast Ethernet ports for copper

and fiber

•Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250 switches),

RSTP/STP, and MSTP for network redundancy

•RADIUS, TACACS+, SNMPv3, IEEE 802.1x, HTTPS, and SSH to

enhance network security

•EtherNet/IP, PROFINET, and Modbus/TCP protocols supported for

device management and monitoring

- 3 -

Panel Views of EDS-528E

1. Reset button

2. USB console port

3. DIP switches for Turbo Ring,

Ring Master, and Ring Coupler

4. Grounding screw

5. 4-

pin terminal block for digital

input and power input 2

6. 4-pin terminal block for relay

output and power input 1

7. 10/100BaseT(X) port, ports 1

to 24

8. 100BaseT(X) LED indicator

9. 10BaseT(X) LED indicator

10.

System status LED:

• STATE LED indicator

• PWR1 LED indicator

• PWR2 LED indicator

• FAULT LED indicator

• MSTR/HEAD LED indicator

• CPLR/TAIL LED indicator

11.

USB storage port

12.

G1 to G4 ports LED indicator

13.

10/100/1000BaseT(X) or

100/1000BaseSFP combo port,

ports G1 to G4

14.

Model Name

15.

Screw hole for Wall Mounting

Kit

16.

DIN-Rail Kit

- 4 -

Mounting Dimensions

Unit = mm (inch)

- 5 -

DIN-Rail Mounting

The metal DIN-rail kit is fixed to the back panel of the EDS-528E when

you take it out of the box. Mount the EDS-528E on corrosion-free

mounting rails that meet the EN 60715 standard.

Installation

STEP 1: Insert the upper lip of the DIN rail into the DIN-rail mounting kit.

STEP 2: Press the EDS-528E series towards the DIN rail until it snaps into

place.

Removal

STEP 1: Pull down the latch on the mounting kit with a screwdriver.

STEPS 2 & 3: Pull the EDS-528E forward slightly and then lift up to

remove it from the DIN rail.

ATTENTION

1. These devices are open-type devices that are to be

installed

in an enclosure with tool removable cover or door suitable

for the environment at that location.

2. This equipment is suitable for use in Class I, Division 2,

Groups A, B, C, and D or non-hazardous locations only.

- 6 -

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the Moxa

EDS-528E on a wall, as shown in the following illustrations:

STEP 1: Remove the

aluminum DIN

-rail

attachment plate from the

rear panel

of the

EDS

-528E, and then

attach the wall mount

plates

with M3 screws

, as

shown

in the figure at

the

right.

STEP 2:

Mounting the EDS-528E series on a wall

requires 4 screws. Use the

EDS-528E

, with wall mount

plates attached, as a guide to mark the correct

locations of the 4 screws. The heads of the screws

should be less than 6.0 mm in diameter, and the shafts

should be less than 3.5

mm in diameter, as shown in

the figure on at the right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the wall mount plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3:

Once the screws

are fixed

to the wall, insert

the four screw heads

through the wide parts of

the keyhole

-shaped

apertures, and then slide

the

EDS-528E downwards,

as in

dicated in the figure at

the right. Tighten the four

screws for greater stability.

WARNING

1. EXPLOSION HAZARD—

Do not disconnect equipment unless

power has been removed or the area is known to be

non-hazardous.

2. EXPLOSION HAZARD—

Substitution of any components may

impair suitability for Class I, Division 2.

3. EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE

SEALING PROPERTIES OF MATERIALS USED IN THE RELAY.

- 7 -

Wiring Requirements

WARNING

Do not

disconnect modules or wires unless power has been

switched off or the area is known to be non

-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

afety Extra-Low V

oltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

afety Extra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

ATTENTION

This unit is a built

-in

type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

EDS-528E.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together

•You should separate input wiring from output wiring

•We advise that you label the wiring to all devices in the system.

- 8 -

Grounding the Moxa EDS-528E

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Wiring the Relay Contact

The EDS-528E series has one relay output. This relay contact uses two

contacts of the terminal block on the EDS-528E’s top panel. Refer to the

next section for detailed instructions on how to connect the wires to the

terminal block connector, and how to attach the terminal block connector

to the terminal block receptor. In this section, we illustrate the meaning

of the two contacts used to connect the relay contact.

FAULT:

The two contacts of the

4-pin terminal

block connector are used to detect

user

-configured events. The two wires

attached to the

fault contacts form an

open circuit when a user

-configured

event is triggered. If a user

-configured

event does not occur, the

fault circuit

remains closed.

Wiring the Redundant Power Inputs

The EDS-528E has two sets of power inputs—power input 1 and power

input 2. The top view of the terminal block connectors is shown here.

STEP 1: Insert the negative/positive DC

wires into the V

-/V+ terminals,

respectively.

STEP 2:

To keep the DC wires from

pulling loose, use a small flat

-blade

screwdriver to tighten the wire

-clamp

screws on the front of the terminal block

connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on

the

EDS-528E’s top panel.

- 9 -

Wiring the Digital Inputs

The EDS-528E has one digital input (DI). The DI consists of two contacts

of the 4-pin terminal block connector on the EDS-528E’s top panel, which

are used for the two DC inputs. The top view of the terminal block

connectors is shown here.

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴

/I terminals, respectively.

STEP 2:

To keep the DI wires from

pulling loose, use a small flat

-blade

screwdriver to tighten the wire

-clamp

screws on the front of the terminal block

connector.

STEP 3

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on

the

EDS-528E’s top panel.

Communication Connections

Each EDS-528E switch has 4 types of communication ports:

•1 USB console port (type B connector)

•1 USB storage port (type A connector)

•24 10/100BaseTX Ethernet ports

•4 Gigabit Ethernet combo ports:

4 10/100/1000BaseT(X) and 4 100/1000BaseSFP ports

USB Console Connection

The EDS-528E has one USB console port (type B connector) located on

the top panel. Use the USB cable (provided in the product package) to

connect the EDS-528E’s console port to your PC’s USB port and install the

USB driver (available on the software CD) on the PC. You may then use a

console terminal program, such as Moxa PComm Terminal Emulator, to

access the EDS-528E’s console configuration utility.

USB Console Port (Type B Connector) Pinouts

Description

D– (Data–)

VCC (+5V)

D+ (Data+)

GND (Ground)

USB Storage Connection

The EDS-528E has one USB storage port (type A connector) on the front

panel. Use the Moxa ABC-02-USB-T automatic backup configurator to

connect the EDS-528E’s USB storage port for configuration backup,

firmware upgrade, or system log file backup.

- 10 -

ABC-02-USB Installation

Plug the ABC-02-USB into the USB

storage port of the Moxa EDS-528E.

The ABC-02-USB can be secured to

the wall with an M4 screw.

USB Storage Port (Type A Connector) Pinouts

Description

VCC (+5V)

D– (Data–)

D+ (Data+)

GND (Ground)

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the EDS-528E’s front panel are

used to connect to Ethernet-enabled devices. Most users will choose to

configure these ports for Auto MDI/MDI-X mode, in which case the port’s

pinouts are adjusted automatically depending on the type of Ethernet

cable used (straight-through or cross-over), and the type of device

(NIC-type or HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

10/100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

Tabla de contenidos

Otros manuales de Cambiar de Moxa Technologies

Moxa Technologies

Moxa Technologies PT-7528 Manual

Moxa Technologies

Moxa Technologies UPORT 1200 series Manual de usuario

Moxa Technologies

Moxa Technologies RKS-G4028 Series Manual de usuario

Moxa Technologies

Moxa Technologies PowerTrans PT-7528-24TX-WV Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manual de usuario

Moxa Technologies

Moxa Technologies UPORT 1200 series Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6700A series Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-205A series Instrucciones de montaje

Moxa Technologies

Moxa Technologies PT-7528 Manual

Moxa Technologies

Moxa Technologies EDS-726 Series Manual

Moxa Technologies

Moxa Technologies IKS-6728-8PoE Manual

Moxa Technologies

Moxa Technologies TN-5508A Series Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Manual de usuario

Moxa Technologies

Moxa Technologies S9450I Series Manual de usuario

Moxa Technologies

Moxa Technologies IESH-MB205G-C2E-R Series Manual de usuario

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PN Manual de usuario

Moxa Technologies

Moxa Technologies ICS-G7526A Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-510E Series Manual de usuario

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Manual

Moxa Technologies

Moxa Technologies OnCell G3111 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-600 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario